{"title":"Proximity Probes \u0026 Cables","description":"\u003cp\u003e\u003cstrong\u003eProximity Probes \u0026amp; Extension Cables\u003c\/strong\u003e are key components of eddy current-based displacement measurement systems used in industrial condition monitoring and protection applications. A typical system consists of a proximity probe, extension cable, and proximitor sensor, forming a calibrated chain that converts shaft vibration or axial position into a stable electrical signal. The probe contains a coil and tip assembly that generates an electromagnetic field, while the extension cable ensures low-loss signal transmission between the probe and monitoring module. These systems support non-contact measurement of vibration, gap, and thrust in rotating machinery such as turbines, compressors, and pumps. Designed for high accuracy and signal stability, they operate reliably in high-temperature and electrically noisy environments. Key technical characteristics include linear response range, temperature compensation, shielded cabling, and precise impedance matching, ensuring consistent performance in long-term industrial monitoring setups.\u003c\/p\u003e","products":[{"product_id":"bently-nevada-330910-05-11-10-02-00-3300-nsv-proximity-probe-m10x1-thread-with-armor","title":"Bently Nevada 330910-05-11-10-02-00 3300 NSv Proximity Probe, M10X1 thread, with  armor","description":"\u003ch3\u003eProduct Overview\u003c\/h3\u003e\n\u003cp\u003eThe\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003e330910-05-11-10-02-00\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eis a rugged, high-reliability eddy-current displacement sensor engineered by Bently Nevada for the specialized\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003e3300 NSv\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eMachinery Diagnostic suite. Featuring standard M10X1 metric casing threads, this non-contacting proximity probe measures precise micro-level radial vibration, shaft axial position, and structural thrust clearances. Heavy-duty rotating assets operating in continuous process environments—including high-speed centrifugal compressors in chemical refining lines, severe-duty industrial refrigeration loops, and process lubrication pumps in power plants—rely on this sensor configuration to capture fast-moving mechanical rotor anomalies. Built with advanced chemical-resistant compounds and a flexible stainless steel armor jacket, the probe survives continuous exposure to volatile hydrocarbons, corrosive gases, and aggressive turbine oils. By transferring clean, high-frequency radio frequency (RF) waveforms directly to an adjacent conditioning Proximitor sensor, this transducer prevents sudden shaft divergence and cuts down on unexpected plant unprogrammed downtime.\u003c\/p\u003e\n\u003ch3\u003ePart Number Suffix Breakdown\u003c\/h3\u003e\n\u003cp\u003eThe specific physical thread engagement dimensions, overall casing length, cable parameters, and safety agency certifications for the\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003e330910-05-11-10-02-00\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003emetric proximity probe are fully mapped via the following factory alphanumeric options.\u003c\/p\u003e\n\u003cul class=\"list-paddingleft-2\"\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e330910 Product Root:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eIdentifies the fundamental hardware platform for the 3300 NSv high-accuracy metric proximity probe with an M10X1 thread specification.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e-05 Unthreaded Length Option:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eSpecifies an unthreaded sleeve length of 50 mm. This smooth upper shaft segment allows precise placement adjustments within thick machine casings or internal compression frames.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e-11 Overall Case Length Option:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eEstablishes a total threaded and unthreaded mechanical case length of 110 mm, measured from the sensing face to the armored transition collar.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e-10 Total Length Option:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eDesignates a continuous 1.0-meter (39 inches) integrated probe cable length from the sensing core to the rear interface point.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e-02 Connector and Cable Type Option:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eEquips the module with a miniature coaxial ClickLoc terminal finished with gold-plated brass pins, paired with a standard-diameter cable wrapped in a rugged, flexible stainless steel armor shield.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e-00 Agency Approval Option:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eIndicates a standard baseline build configuration intended for general industrial deployment zones where localized hazardous-area explosion-proof certifications are not required.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eTechnical Specifications \u0026amp; Operating Thresholds\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr class=\"firstRow\"\u003e\n\u003ctd\u003e\u003cstrong\u003eMechanical Protection Parameter\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cstrong\u003eIndustrial Transducer Engineering Value\u003c\/strong\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eModel Identity\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e330910-05-11-10-02-00\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eBrand Manufacturer\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eBently Nevada (Baker Hughes Business Unit)\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eControl System Line\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e3300 NSv Proximity Transducer Series\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eThread Mounting Profile\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eM10X1 Metric Thread with Integrated Protective Armor\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eInterchangeable Ancestry\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eFully compatible with legacy 3300 RAM series components\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eTerminal Connector Type\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eGold-Plated Brass Miniature Coaxial ClickLoc Connector\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eSensing Structural Joins\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003ePatented TipLoc Mold Core \/ CableLoc 220 N Pull Joint\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eThread Engagement Bound\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e15 mm Maximum Thread Structural Engagement Limit\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eLinear Target Calibration\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eFactory optimized to AISI 4140 Steel substrate lines\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eOperating Thermal Window\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e-52 to +177 deg C Continuous Ambient Range\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eStorage Temperature Bounds\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e-52 to +177 deg C Structural Storage Envelope\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003ePower Consumption Parameters\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003ePassive sensor matrix powered via external Proximitor\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eMachinery Telemetry \u0026amp; Diagnostics FAQs\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eWhat specific operational advantages does the 3300 NSv probe offer over the legacy 3000-series 190 probe?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe 3300 NSv probe features superior side-view characteristics compared to older 3000-series 190 models when gapped at identical distances from the machine target. This geometric optimization prevents adjacent housing metals from distorting the electromagnetic field, delivering a much cleaner proximity reading with minimal cross-talk or side-wall interference.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan this metric probe be used interchangeably in an existing 3300 RAM system configuration?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eYes. The 3300 NSv probe and its corresponding extension cables are mechanically and electrically backward-compatible with Bently Nevada's legacy 3300 RAM series. However, the NSv series is built with superior chemical resistance, making it much better suited for process compressor environments where aggressive chemical mixtures could degrade older probe tips.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat happens if the 3300 NSv probe is exposed to temperatures below -34 deg C for extended periods?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eWhile the probe is rated to an absolute thermal floor of -52 deg C, exposing the assembly to temperatures below -34 deg C for long periods can cause the internal pressure seals to age prematurely. In high-pressure compressor casings, this degradation can compromise the seal integrity, potentially leading to process gas leaks through the probe body.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch3\u003eEngineering \u0026amp; Installation Guide\u003c\/h3\u003e\n\u003cul class=\"list-paddingleft-2\"\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003eClickLoc Terminal Seating and Connector Insulation:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eConnect the probe's miniature coaxial ClickLoc fitting to the extension cable by pushing until the gold-plated contacts click into place. To protect the high-frequency RF signal from moisture, dust, or oil contamination, always install a dedicated connector protector over the junction. If connector protectors are unavailable, wrap the junction securely with self-fusing silicone tape. However, do not use silicone tape if the connection will be directly exposed to turbine oil, as hydrocarbons will dissolve the tape adhesive over time.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003eMechanical Torque Constraints and Cable Strain Relief:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThread the M10X1 casing carefully into the machine bracket, ensuring total thread engagement does not exceed the 15 mm structural limit. Tighten the locking nut to standard engineering torque specifications to prevent the assembly from backing out under severe machinery vibration. The integrated CableLoc design provides up to 220 N (50 lbs) of continuous pull strength, but engineers should still secure the armored run to the machine casing using rigid clips to prevent whip damage.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003eTarget Clearance Voltage Alignment Protocols:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eSet the physical gap clearance by monitoring the raw DC voltage output at the Proximitor sensor terminals with a digital multimeter. Adjust the depth of the M10X1 casing until the meter reads the exact target voltage specified by the loop calibration framework. This alignment ensures the probe tip sits precisely within its linear measuring range, keeping the signal clear of low-end or high-end voltage saturation zones.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666515358059,"sku":"330910-05-11-10-02-00","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330910-05-11-10-02-00-nsv-proximity-probes-otahhoabrmu_a7181322-b1ed-4090-b09e-a46e2ccb787e.jpg?v=1765440076"},{"product_id":"bently-nevada-330910-014-19-10-02-00-3300-nsv-proximity-probe","title":"Bently Nevada 330910-014-19-10-02-00 3300 NSv Proximity Probe","description":"\u003ch3\u003eProduct Overview\u003c\/h3\u003e\n\u003cp\u003eThe\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003e330910-014-19-10-02-00\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eis a high-precision, non-contacting eddy-current displacement sensor engineered by Bently Nevada for the specialized\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003e3300 NSv\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eMachinery Diagnostic platform. This metric-threaded M10X1 probe monitors fine radial vibration, axial thrust position, and dynamic fluid-film bearing constraints under high-velocity conditions. Critical process infrastructure installations—including high-speed centrifugal gas compressors in petrochemical refineries, severe-duty industrial refrigeration loops, and process water pumps in power generation plants—rely on this sensor array to detect micro-level rotor instabilities. Featuring patented TipLoc structural molding and robust stainless steel armor plating, the probe stands up to volatile chemical environments and turbulent oil shear. By sending stable analog waveforms directly to a companion Proximitor conditioning device, the probe catches early mechanical imbalance, preventing catastrophic rotor lockups and significantly lowering unprogrammed operational downtime.\u003c\/p\u003e\n\u003ch3\u003ePart Number Suffix Breakdown\u003c\/h3\u003e\n\u003cp\u003eThe mechanical dimensions, case variations, structural shield layers, and safety certifications for the\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003e330910-014-19-10-02-00\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003etransducer probe can be broken down using the following engineering suffix definitions.\u003c\/p\u003e\n\u003cul class=\"list-paddingleft-2\"\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e330910 Part Root:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eDesignates the primary platform for the 3300 NSv high-precision metric proximity probe with an M10X1 thread profile.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e-014 Unthreaded Length:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eDefines a specific unthreaded case length of 140 mm. This smooth upper shaft provides deep clearance adjustments through external machinery casing walls.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e-19 Overall Case Length:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eEstablishes a total mechanical case length of 190 mm from the base of the sensing tip to the back of the armored cable transition collar.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e-10 Total Cable Length:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eSpecifies a 1.0-meter (39 inches) continuous integrated probe cable length, measured from tip to connector pin.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e-02 Connector and Cable Type:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eEquips the module with a miniature coaxial ClickLoc terminal finished with heavy gold-plated brass contacts, paired with a standard-diameter cable protected by rugged, flexible stainless steel armor.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e-00 Agency Approval Selection:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eIndicates standard uncertified hardware configuration where localized hazardous location safety approvals are not required for the mounting zone.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eTechnical Specifications \u0026amp; Operating Thresholds\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr class=\"firstRow\"\u003e\n\u003ctd\u003e\u003cstrong\u003eMechanical Protection Parameter\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cstrong\u003eIndustrial Transducer Engineering Value\u003c\/strong\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eModel Designation\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e330910-014-19-10-02-00\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eBrand Manufacturer\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eBently Nevada (Baker Hughes Business Unit)\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eControl System Line\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e3300 NSv Proximity Transducer Series\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eThread Mounting Profile\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eM10X1 Metric Thread with Integrated Protective Armor\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eInterchangeable Ancestry\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eFully compatible with legacy 3300 RAM series components\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eTerminal Connector Type\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eGold-Plated Brass Miniature Coaxial ClickLoc Connector\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eSensing Structural Joins\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003ePatented TipLoc Mold Core \/ CableLoc 220 N Pull Joint\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003ePhysical Hardware Weight\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eApproximately 14 g to 150 g based on armor options\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eThread Engagement Bound\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e15 mm Maximum Thread Structural Engagement Limit\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eLinear Target Calibration\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eFactory optimized to AISI 4140 Steel substrate lines\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eOperating Thermal Window\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e-52 to +177 deg C Continuous Ambient Range\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eStorage Temperature Bounds\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e-52 to +177 deg C Structural Storage Envelope\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003ePower Consumption Parameters\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003ePassive sensor matrix powered via external Proximitor\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eMachinery Telemetry \u0026amp; Diagnostics FAQs\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eWhat specific operational advantages does the 3300 NSv probe offer over the legacy 3000-series 190 probe?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe 3300 NSv probe features superior side-view characteristics compared to older 3000-series 190 models when gapped at identical distances from the machine target. This geometric optimization prevents adjacent housing metals from distorting the electromagnetic field, delivering a much cleaner proximity reading with minimal cross-talk or side-wall interference.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan this metric probe be used interchangeably in an existing 3300 RAM system configuration?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eYes. The 3300 NSv probe and its corresponding extension cables are mechanically and electrically backward-compatible with Bently Nevada's legacy 3300 RAM series. However, the NSv series is built with superior chemical resistance, making it much better suited for process compressor environments where aggressive chemical mixtures could degrade older probe tips.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat happens if the 3300 NSv probe is exposed to temperatures below -34 deg C for extended periods?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eWhile the probe is rated to an absolute thermal floor of -52 deg C, exposing the assembly to temperatures below -34 deg C for long periods can cause the internal pressure seals to age prematurely. In high-pressure compressor casings, this degradation can compromise the seal integrity, potentially leading to process gas leaks through the probe body.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch3\u003eEngineering \u0026amp; Installation Guide\u003c\/h3\u003e\n\u003cul class=\"list-paddingleft-2\"\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003eClickLoc Terminal Seating and Connector Insulation:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eConnect the probe's miniature coaxial ClickLoc fitting to the extension cable by pushing until the gold-plated contacts click into place. To protect the high-frequency RF signal from moisture, dust, or oil contamination, always install a dedicated connector protector over the junction. If connector protectors are unavailable, wrap the junction securely with self-fusing silicone tape. However, do not use silicone tape if the connection will be directly exposed to turbine oil, as hydrocarbons will dissolve the tape adhesive over time.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003eMechanical Torque Constraints and Cable Strain Relief:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThread the M10X1 casing carefully into the machine bracket, ensuring total thread engagement does not exceed the 15 mm structural limit. Tighten the locking nut to standard engineering torque specifications to prevent the assembly from backing out under severe machinery vibration. The integrated CableLoc design provides up to 220 N (50 lbs) of continuous pull strength, but engineers should still secure the armored run to the machine casing using rigid clips to prevent whip damage.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003eTarget Clearance Voltage Alignment Protocols:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eSet the physical gap clearance by monitoring the raw DC voltage output at the Proximitor sensor terminals with a digital multimeter. Adjust the depth of the M10X1 casing until the meter reads the exact target voltage specified by the loop calibration framework. This alignment ensures the probe tip sits precisely within its linear measuring range, keeping the signal clear of low-end or high-end voltage saturation zones.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666515456363,"sku":"330910-014-19-10-02-00","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330910-014-19-10-02-00-8mm-proximity-probe-c3pcvvxmr2m_37a075a4-b569-4d09-993e-143dcd278d87.jpg?v=1765440077"},{"product_id":"bently-nevada-330910-00-05-10-02-00-3300-nsv-proximity-probe","title":"Bently Nevada 330910-00-05-10-02-00 3300 NSv Proximity Probe","description":"\u003ch3\u003eProduct Overview\u003c\/h3\u003e\n\u003cp\u003eThe\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003e330910-00-05-10-02-00 (3300 NSv)\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eis a high-precision industrial eddy-current sensor designed for machinery with restrictive installation requirements. Belonging to the Narrow Side View (NSv) series, this probe is specifically engineered for centrifugal air compressors, refrigeration compressors, and small-bore process pumps where standard 8 mm sensors would suffer from signal interference. The\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003e330910-00-05-10-02-00\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eexcels in measuring radial vibration and axial position on small shafts (under 51 mm) or narrow targets (under 15 mm). Utilizing Bently Nevada's patented\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003eTipLoc\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eand\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003eCableLoc\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003etechnologies, the probe ensures a robust bond between the tip and body and provides 220 N of pull strength, making it ideal for the aggressive process environments of power plants and chemical refineries.\u003c\/p\u003e\n\u003ch3\u003eSuffix Configuration Breakdown\u003c\/h3\u003e\n\u003cp\u003eAccording to the technical specifications in Datasheet 147385, the model\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003e330910-00-05-10-02-00\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003efollows this mechanical and electrical build:\u003c\/p\u003e\n\u003cul class=\"list-paddingleft-2\"\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e330910:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e3300 NSv Proximity Probe with M10X1 metric threading.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e00 (Unthreaded Length Option):\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e0 mm unthreaded case length.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e05 (Overall Case Length Option):\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e50 mm total case length.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e10 (Total Length Option):\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e1.0 meter (3.3 feet) integrated probe lead.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e02 (Connector and Cable-Type Option):\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eEquipped with a miniature coaxial ClickLoc connector and standard cable (without armor).\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e00 (Agency Approval Option):\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eStandard version with no specific hazardous area certifications required.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr class=\"firstRow\"\u003e\n\u003ctd\u003e\u003cstrong\u003eFeature\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eModel\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e330910-00-05-10-02-00\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eBrand\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eBently Nevada\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eThread Type\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eM10X1 (Metric)\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eLinear Range\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e1.5 mm (60 mils)\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eScale Factor\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e7.87 V\/mm (200 mV\/mil)\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eOperating Temp\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e-52 to +177 deg C\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eCable Jacket\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eFluorinated Ethylene Propylene (FEP)\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eTarget Material\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eAISI 4140 Steel (Standard)\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eConnector\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eGold-plated brass ClickLoc\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003ePressure Sealing\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eViton O-ring between tip and body\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eEngineering FAQs\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eWhat are the primary benefits of the NSv Narrow Side View design?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eStandard 8 mm probes have a wide magnetic field that \"sees\" the sides of a mounting hole, creating an offset error. The NSv design focuses the field at the tip, allowing installation in much smaller counterbores and making it the superior choice for monitoring vibration on small-diameter shafts where side-view interference is a concern.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIs the ClickLoc connector reliable in high-vibration applications?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eYes. The ClickLoc is a patented locking mechanism. Unlike standard threaded connectors that can vibrate loose over time, the ClickLoc \"clicks\" into a secured mechanical state, ensuring a constant electrical connection and stable signal impedance for the 3500 monitoring system.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I use this probe with a standard 3300 XL extension cable?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eNo. The 3300 NSv series is electrically distinct from the standard 3300 XL 8 mm series. This probe must be paired with a 3300 NSv extension cable and a 3300 XL NSv Proximitor Sensor. Mixing components will lead to incorrect scale factors and inaccurate machinery data.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch3\u003eField Installation and Maintenance Directives\u003c\/h3\u003e\n\u003cul class=\"list-paddingleft-2\"\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003eTorque Specifications:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eFor M10X1 probe cases, the recommended installation torque is\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003e7.5 N-m (66 in-lb)\u003c\/strong\u003e. Never exceed the maximum rated torque of 22.6 N-m (200 in-lb). Over-tightening can cause case elongation and permanently shift the internal coil's calibration point.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003eGap Voltage Setting:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eFor standard AISI 4140 steel, set the probe gap to achieve a bias voltage of\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003e-10 Vdc\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eat the Proximitor Sensor output. This represents the center of the 1.5 mm linear range, ensuring the monitor can capture both positive and negative vibration peaks without clipping.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003eEnvironmental Sealing:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eWhile the probe is rated for high temperatures, exposure below\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003e-34 deg C (-30 deg F)\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003efor sustained periods may cause the pressure seal to fail. Always use the provided self-fusing silicone tape to wrap the probe-to-extension cable connection to prevent moisture or oil ingress from affecting the ClickLoc signal.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003eCable Routing:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eSince this model (\u003cstrong\u003eOption 02\u003c\/strong\u003e) does not have stainless steel armor, the cable must be protected within a rigid or flexible conduit if it is routed through areas where it may be stepped on, crushed, or exposed to sharp edges. Maintain a minimum bend radius of\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003e25.4 mm (1 inch)\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eat all times.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003e\u003c\/h3\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666515751275,"sku":"330910-00-05-10-02-00","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330910-00-05-10-02-00-nsv-proximity-probes-b0elfrnkzmo_edd5ce75-b668-4b93-a723-8bcf99b489af.jpg?v=1765440082"},{"product_id":"bently-nevada-330905-14-19-10-02-05-3300-nsv-proximity-probe","title":"Bently Nevada 330905-14-19-10-02-05 3300 NSv Proximity Probe","description":"\u003ch3\u003eProduct Overview\u003c\/h3\u003e\n\u003cp\u003eThe\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003e330905-14-19-10-02-05 (3300 NSv)\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eis a high-precision eddy-current displacement sensor designed for industrial machinery with extreme space constraints. Specifically engineered for use in centrifugal air compressors, refrigeration units, and high-speed process gas compressors, this probe excels where standard 8 mm sensors face physical limitations. The\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003e330905-14-19-10-02-05\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eutilizes Narrow Side View (NSv) technology to provide accurate radial vibration and axial position measurements on small-diameter shafts (under 51 mm) or restricted thrust targets. By focusing the electromagnetic field at the tip, it eliminates signal interference caused by counterbore walls or adjacent metallic surfaces. This sensor is a vital component in machinery protection systems, offering the reliability needed to prevent catastrophic failures and optimize asset uptime in aggressive chemical and thermal environments.\u003c\/p\u003e\n\u003ch3\u003eSuffix Configuration Breakdown\u003c\/h3\u003e\n\u003cp\u003eThe ordering suffix for the\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003e330905-14-19-10-02-05\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003edefines a highly specific mechanical and regulatory build:\u003c\/p\u003e\n\u003cul class=\"list-paddingleft-2\"\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e330905:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e3300 NSv Proximity Probe, Metric (M10X1 thread).\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e14 (Unthreaded Length):\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e140 mm unthreaded case length.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e19 (Overall Case Length):\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e190 mm total case length.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e10 (Total Length):\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e1.0 meter (39 inches) integrated lead cable.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e02 (Connector\/Cable):\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eEquipped with a miniature coaxial ClickLoc connector and standard cable (without armor).\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e05 (Agency Approval):\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eMultiple Approvals (ATEX, IECEx, CSA) for use in intrinsically safe and hazardous area installations.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr class=\"firstRow\"\u003e\n\u003ctd\u003e\u003cstrong\u003eAttribute\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eModel\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e330905-14-19-10-02-05\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eBrand\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eBently Nevada\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eThread Size\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eM10X1 (Metric)\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eLinear Range\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e1.5 mm (60 mils)\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eScale Factor\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e7.87 V\/mm (200 mV\/mil)\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eOperating Temp\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e-52 deg C to +177 deg C\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eConnector Type\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eGold-plated ClickLoc\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eTensile Strength\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e220 N (50 lb) cable-to-tip\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eJacket Material\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eFluorinated Ethylene Propylene (FEP)\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eTypical Weight\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e14 g to 150 g (Probe dependent)\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eCalibration Target\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eAISI 4140 Steel (Standard)\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eEngineering FAQs\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eWhat distinguishes the NSv series from standard 3300 XL probes?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe NSv (Narrow Side View) series uses a smaller coil and a more focused magnetic field. This allows it to monitor vibration on shafts as small as 51 mm (2 in) without the signal distortion that occurs when a standard probe's field \"spills\" over the side of a narrow shaft.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I install this probe without a protective conduit?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eSince this specific model (\u003cstrong\u003eOption 02\u003c\/strong\u003e) is \"without armor,\" the coaxial cable is exposed. While the FEP jacket provides excellent chemical resistance, it is vulnerable to mechanical crushing or cutting. For unprotected runs, we recommend routing the cable through dedicated rigid or flexible conduit.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow does the ClickLoc connector handle high-vibration environments?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe ClickLoc is a patented self-locking connector. Unlike standard threaded SMA or BNC connectors that may loosen over time due to machine resonance, the ClickLoc \"clicks\" into a fixed mechanical state, ensuring a constant electrical connection and stable impedance.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch3\u003eField Installation and Maintenance Directives\u003c\/h3\u003e\n\u003cul class=\"list-paddingleft-2\"\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003eTorque and Mounting Safety:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eFor M10X1 probe cases, the recommended installation torque is\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003e7.5 N-m (66 in-lb)\u003c\/strong\u003e. Never exceed the absolute maximum of 22.6 N-m (200 in-lb). Over-torquing can lead to case elongation, which shifts the internal coil and permanently alters the sensor's calibration.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003eGap Voltage Calibration:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eFor standard AISI 4140 steel, set the probe gap to achieve a bias voltage of\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003e-10 Vdc\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eat the Proximitor Sensor output. This voltage indicates the probe is at the center of its 1.5 mm linear range, allowing for equal measurement of positive and negative vibration peaks.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003eEnvironmental Sealing:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eThe probe is rated for high temperatures, but exposure below\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003e-34 deg C (-30 deg F)\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003efor extended periods can damage the internal pressure seal. Ensure that the ClickLoc connector is kept clean and dry; if the connection is made in an area with potential fluid ingress, seal it with the provided self-fusing silicone tape.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003eSystem Matching:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eThe 3300 NSv is a specialized system. The\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003e330905\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eprobe must be used with a 3300 NSv extension cable and a 3300 XL NSv Proximitor Sensor. Mixing these components with standard 3300 XL 8mm parts will result in a \"Not OK\" status or incorrect scale factors.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003e\u003c\/h3\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666515784043,"sku":"330905-14-19-10-02-05","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330905-14-19-10-02-05-proximity-probes-pb2vquexk5e_88cb443c-9def-4895-822c-d2514228d0f1.jpg?v=1765440083"},{"product_id":"bently-nevada-330910-10-22-10-01-cn-3300-nsv-proximity-probe","title":"Bently Nevada 330910-10-22-10-01-CN 3300 NSv Proximity Probe","description":"\u003ch3\u003eProduct Overview\u003c\/h3\u003e\n\n\u003cp\u003eThe \u003cstrong\u003e330910-10-22-10-01-CN (3300 NSv)\u003c\/strong\u003e is a specialized eddy-current proximity sensor engineered for high-precision displacement monitoring in restricted industrial spaces. As part of the Bently Nevada 3300 XL NSv series, this probe is specifically designed for centrifugal air compressors and refrigeration units where small shaft diameters (under 51 mm) or tight side-view clearances are present. The \u003cstrong\u003e330910-10-22-10-01-CN\u003c\/strong\u003e provides critical radial vibration and axial position data, utilizing a focused Narrow Side View (NSv) field that prevents interference from counterbore walls. This specific \"-CN\" variant is fully localized for the Chinese market, ensuring compliance with domestic safety and environmental regulations while maintaining the world-class machinery protection standards required to prevent catastrophic failure and reduce plant downtime.\u003c\/p\u003e\n\n\u003ch3\u003eSuffix Configuration Breakdown\u003c\/h3\u003e\n\n\u003cp\u003eThe alphanumeric code \u003cstrong\u003e330910-10-22-10-01-CN\u003c\/strong\u003e defines the exact mechanical and regulatory build of the transducer:\u003c\/p\u003e\n\n\u003cul class=\"list-paddingleft-2\"\u003e\n\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e330910:\u003c\/strong\u003e 3300 NSv Proximity Probe with M10X1 metric threading.\u003c\/p\u003e\n\u003c\/li\u003e\n\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e10 (Unthreaded Length):\u003c\/strong\u003e 10 mm unthreaded length on the probe case.\u003c\/p\u003e\n\u003c\/li\u003e\n\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e22 (Overall Case Length):\u003c\/strong\u003e 220 mm total case length for deep mounting requirements.\u003c\/p\u003e\n\u003c\/li\u003e\n\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e10 (Total Length):\u003c\/strong\u003e 1.0 meter (3.3 feet) integrated probe lead length.\u003c\/p\u003e\n\u003c\/li\u003e\n\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e01 (Connector\/Cable):\u003c\/strong\u003e Miniature coaxial ClickLoc connector with integrated stainless steel armor for mechanical protection.\u003c\/p\u003e\n\u003c\/li\u003e\n\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003eCN (China Specific Approval):\u003c\/strong\u003e Mandatory certification suffix for the People's Republic of China, covering \u003cstrong\u003eNEPSI\u003c\/strong\u003e, \u003cstrong\u003eCCC\u003c\/strong\u003e, \u003cstrong\u003eSRRC\u003c\/strong\u003e, and \u003cstrong\u003eChina RoHS\u003c\/strong\u003e (50-year environment-friendly use period).\u003c\/p\u003e\n\u003c\/li\u003e\n\n\u003c\/ul\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\n\u003ctable\u003e\n\n\u003cthead\u003e\n\n\u003ctr class=\"firstRow\"\u003e\n\u003cth\u003eAttribute\u003c\/th\u003e\n\u003cth\u003eSpecification\u003c\/th\u003e\n\u003c\/tr\u003e\n\n\u003c\/thead\u003e\n\n\u003ctbody\u003e\n\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eModel\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e330910-10-22-10-01-CN\u003c\/td\u003e\n\u003c\/tr\u003e\n\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eBrand\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eBently Nevada\u003c\/td\u003e\n\u003c\/tr\u003e\n\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eThread Size\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eM10X1\u003c\/td\u003e\n\u003c\/tr\u003e\n\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eCertifications\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eNEPSI, CCC, SRRC, China RoHS (50 years)\u003c\/td\u003e\n\u003c\/tr\u003e\n\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eLinear Range\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e1.5 mm (60 mils)\u003c\/td\u003e\n\u003c\/tr\u003e\n\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eScale Factor\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e7.87 V\/mm (200 mV\/mil)\u003c\/td\u003e\n\u003c\/tr\u003e\n\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOperating Temp\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e-52 to +177 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eTensile Strength\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e220 N (50 lb) probe to cable\u003c\/td\u003e\n\u003c\/tr\u003e\n\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eArmor Material\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eFlexible AISI 302 Stainless Steel\u003c\/td\u003e\n\u003c\/tr\u003e\n\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePressure Sealing\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eViton O-ring between tip and case\u003c\/td\u003e\n\u003c\/tr\u003e\n\n\u003c\/tbody\u003e\n\n\u003c\/table\u003e\n\n\u003ch3\u003eIndustrial Engineering FAQs\u003c\/h3\u003e\n\n\u003cp\u003e\u003cstrong\u003eWhat is the significance of the -CN suffix for my project?\u003c\/strong\u003e The -CN suffix ensures the device is legally compliant for installation within the People's Republic of China. It verifies that the probe meets local explosive safety (NEPSI) and mandatory certification (CCC) laws. Functionally, it is identical to global 3300 XL sensors but includes the necessary local labeling and documentation required by Chinese inspectors.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eHow does the NSv technology handle \"Side-View\" interference?\u003c\/strong\u003e Standard probes have a wider magnetic field that can \"see\" the sides of a mounting hole, causing false readings. The NSv (Narrow Side View) technology focuses the field at the tip, allowing the probe to be installed in much tighter counterbores or closer to adjacent metal surfaces without signal distortion.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eIs the stainless steel armor necessary for all applications?\u003c\/strong\u003e While not mandatory for signal transmission, the armor (Option 01) is highly recommended in heavy industrial environments where cables are exposed to foot traffic, falling tools, or mechanical abrasion. The armor also provides an additional layer of protection against RF interference when properly grounded.\u003c\/p\u003e\n\n\u003chr\u003e\n\n\u003ch3\u003eField Installation and Maintenance Directives\u003c\/h3\u003e\n\n\u003cul class=\"list-paddingleft-2\"\u003e\n\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003eTorque and Engagement:\u003c\/strong\u003e For the M10X1 probe case, the recommended installation torque is \u003cstrong\u003e7.5 N-m (66 in-lb)\u003c\/strong\u003e. To preserve the integrity of the case and the internal coil, never exceed the maximum rated torque of 22.6 N-m (200 in-lb). Ensure at least 15 mm of thread engagement for a secure mount.\u003c\/p\u003e\n\u003c\/li\u003e\n\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003eGap Voltage Calibration:\u003c\/strong\u003e For standard AISI 4140 steel targets, set the probe gap to achieve approximately \u003cstrong\u003e-10 Vdc\u003c\/strong\u003e at the Proximitor Sensor output. This represents the center of the 1.5 mm linear range. Always verify this voltage with a calibrated digital multimeter before locking the mounting nut.\u003c\/p\u003e\n\u003c\/li\u003e\n\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003eEnvironmental Sealing:\u003c\/strong\u003e Although the probe is rated for high temperatures, long-term exposure to temperatures below -34 deg C (-30 deg F) can cause the pressure seal to fail prematurely. For installations in chemical or oil-heavy areas, use the provided silicone tape or dedicated connector protectors to prevent fluid ingress into the ClickLoc connector.\u003c\/p\u003e\n\u003c\/li\u003e\n\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003eRegulatory Compliance in China:\u003c\/strong\u003e When installing the -CN version, ensure the NEPSI and CCC labels remain visible and undamaged. These markings are required for the facility's safety audit and confirm the 50-year China RoHS compliance for environmental safety.\u003c\/p\u003e\n\u003c\/li\u003e\n\n\u003c\/ul\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666516177259,"sku":"330910-10-22-10-01-CN","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330910-10-22-10-01-cn-3300-nsv-proximity-probe-n53vu5tpjqv_47b60ae9-d079-4d0e-9487-a090f64e7020.jpg?v=1765440086"},{"product_id":"bently-nevada-330909-00-99-10-02-00-3300-nsv-proximity-probe","title":"Bently Nevada 330909-00-99-10-02-00 3300 NSv Proximity Probe","description":"\u003ch3\u003eProduct Overview\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003e330909-00-99-10-02-00 (3300 NSv)\u003c\/strong\u003e is a specialized eddy-current proximity transducer designed for industrial machinery with high-density installation requirements, such as centrifugal air compressors and refrigeration units. As part of the Narrow Side View (NSv) family, this probe is engineered for applications where standard sensors encounter physical restrictions like counterbores or limited side-view clearance. The \u003cstrong\u003e330909-00-99-10-02-00\u003c\/strong\u003e provides critical radial vibration and axial position data for fluid-filmed bearing machines, featuring enhanced chemical resistance and superior side-view characteristics compared to legacy RAM and 3000-series sensors. Its robust construction, including integrated stainless steel armor, ensures long-term reliability in harsh environments, effectively reducing unplanned downtime through high-fidelity machinery diagnostics.\u003c\/p\u003e\n\n\u003ch3\u003eSuffix Configuration Breakdown\u003c\/h3\u003e\n\u003cp\u003eThe model number \u003cstrong\u003e330909-00-99-10-02-00\u003c\/strong\u003e specifies a highly customized hardware configuration:\u003c\/p\u003e\n\n\u003cul class=\"list-paddingleft-2\"\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e330909:\u003c\/strong\u003e Identifies the 3300 NSv Proximity Probe with 3\/8-24 UNF threads and integrated stainless steel armor.\u003c\/p\u003e\n\u003c\/li\u003e\n\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e00 (Unthreaded Length Option):\u003c\/strong\u003e Specifies a 0.0 inch unthreaded length.\u003c\/p\u003e\n\u003c\/li\u003e\n\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e99 (Overall Case Length Option):\u003c\/strong\u003e Indicates a maximum case length of 9.9 inches.\u003c\/p\u003e\n\u003c\/li\u003e\n\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e10 (Total Length Option):\u003c\/strong\u003e Specifies a 1.0 meter (39 inch) total probe length.\u003c\/p\u003e\n\u003c\/li\u003e\n\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e02 (Connector and Cable-Type Option):\u003c\/strong\u003e Equipped with a miniature coaxial ClickLoc connector and standard cable.\u003c\/p\u003e\n\u003c\/li\u003e\n\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e00 (Agency Approval Option):\u003c\/strong\u003e Standard version with no specific hazardous area approvals required.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr class=\"firstRow\"\u003e\n\u003ctd\u003e\u003cstrong\u003eFeature\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eModel\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e330909-00-99-10-02-00\u003c\/td\u003e\n\u003c\/tr\u003e\n\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eBrand\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eBently Nevada\u003c\/td\u003e\n\u003c\/tr\u003e\n\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eThread Type\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e3\/8-24 UNF-2A\u003c\/td\u003e\n\u003c\/tr\u003e\n\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eArmor Type\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eFlexible AISI 302 SST\u003c\/td\u003e\n\u003c\/tr\u003e\n\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eLinear Range\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e1.5 mm (60 mils)\u003c\/td\u003e\n\u003c\/tr\u003e\n\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eScale Factor\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e7.87 V\/mm (200 mV\/mil)\u003c\/td\u003e\n\u003c\/tr\u003e\n\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOperating Temperature\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e-52 to +177 deg C (-62 to +351 deg F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePressure Sealing\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eViton O-ring (tip to case)\u003c\/td\u003e\n\u003c\/tr\u003e\n\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eTensile Strength\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e220 N (50 lb) probe case to lead\u003c\/td\u003e\n\u003c\/tr\u003e\n\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eRecommended Gap\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e1.0 mm (40 mils)\u003c\/td\u003e\n\u003c\/tr\u003e\n\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eMaterial (Tip)\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003ePolyphenylene sulfide (PPS)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eAsset Reliability FAQs\u003c\/h3\u003e\n\n\u003cp\u003e\u003cstrong\u003eCan this NSv probe replace my older 3000-series 190 transducer?\u003c\/strong\u003e Yes. The 3300 XL NSv system is designed to replace both 3300 RAM and 3000-series\/7000-series 190 systems. Note that when upgrading from a 3000-series system, you must replace the probe, extension cable, and Proximitor Sensor simultaneously.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eWhat are the limitations of the \"Narrow Side View\" design?\u003c\/strong\u003e While superior in tight spaces, the NSv series has a shorter linear range (1.5 mm) compared to standard Bently Nevada 3300 XL 5 mm or 8 mm systems. It is specifically optimized for targets smaller than 15 mm or shafts smaller than 51 mm.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eIs it necessary to use connector protectors with the ClickLoc system?\u003c\/strong\u003e Connector protectors are highly recommended as they prevent liquids and environmental contaminants from entering the ClickLoc interface, which could otherwise degrade the electrical signal. For applications involving turbine oil, silicone tape is not a suitable substitute for these protectors.\u003c\/p\u003e\n\n\u003chr\u003e\n\n\u003ch3\u003eField Engineering and Installation Directives\u003c\/h3\u003e\n\n\u003cul class=\"list-paddingleft-2\"\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003eTorque Specifications:\u003c\/strong\u003e For 3\/8-24 threaded cases, the maximum rated torque is 33.9 N-m (300 in-lb). For the first three threads of engagement, use a reduced recommended torque of 7.5 N-m (66 in-lb) to avoid stripping.\u003c\/p\u003e\n\u003c\/li\u003e\n\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003eMounting Depth Limits:\u003c\/strong\u003e The maximum length of thread engagement for a 3\/8-24 probe is 0.563 inches. Exceeding this limit can cause mechanical binding during installation and will void the Bently Nevada warranty.\u003c\/p\u003e\n\u003c\/li\u003e\n\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003eSignal Integrity:\u003c\/strong\u003e Ensure the ClickLoc connectors are \"clicked\" firmly into place. The gold-plated contacts and patented CableLoc design provide 220 N of pull strength to prevent accidental disconnection during high-vibration operation.\u003c\/p\u003e\n\u003c\/li\u003e\n\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003eGap Voltage Target:\u003c\/strong\u003e Proximitor Sensors are factory-calibrated to AISI 4140 steel. For precise measurement, the probe should be gapped at 1.0 mm (40 mils), typically resulting in a -10 Vdc bias point in the center of the linear range.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666516439403,"sku":"330909-00-99-10-02-00","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330909-00-99-10-02-00-nsv-proximity-sensor-jcvvqwmikny_0be8fad0-00f2-4633-b7a3-e282747dd0a7.jpg?v=1765440091"},{"product_id":"bently-nevada-330910-00-05-50-02-00-3300-nsv-proximity-probe","title":"Bently Nevada 330910-00-05-50-02-00 3300 NSv Proximity Probe","description":"\u003ch3\u003eProduct Overview\u003c\/h3\u003e\n\u003cp\u003eThe\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003e330910-00-05-50-02-00\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eis a high-precision eddy-current displacement sensor belonging to the 3300 NSv (Narrow Side View) series. Engineered specifically for confined industrial spaces where standard probes encounter side-view interference, this model is a critical component in the vibration monitoring of centrifugal compressors, high-speed pumps, and small-bore turbines. The\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003e330910-00-05-50-02-00\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eprovides superior chemical resistance compared to legacy RAM probes, ensuring stable performance in aggressive process media found in oil refineries and chemical plants. By delivering high-fidelity shaft vibration and position data, it enables predictive maintenance strategies that significantly reduce unplanned downtime and protect high-value rotating assets from catastrophic failure.\u003c\/p\u003e\n\u003ch3\u003eSuffix Configuration Breakdown\u003c\/h3\u003e\n\u003cp\u003eThe alphanumeric string for the\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003e330910-00-05-50-02-00\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003edefines the following mechanical and electrical specifications:\u003c\/p\u003e\n\u003cul class=\"list-paddingleft-2\"\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e00 (Unthreaded Length):\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e0 mm unthreaded case section.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e05 (Overall Case Length):\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e50 mm total case length, providing a compact footprint for shallow casing penetrations.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e50 (Total Length):\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e5.0 meters (16.4 feet) system length, eliminating the need for separate extension cables in specific configurations.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e02 (Connector\/Cable):\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eEquipped with miniature coaxial ClickLoc connectors and standard cable with integrated stainless steel armor for maximum physical protection.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e00 (Agency Approval):\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eNo specific hazardous area certification required for this specific variant.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr class=\"firstRow\"\u003e\n\u003ctd\u003e\u003cstrong\u003eFeature\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eModel\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e330910-00-05-50-02-00\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eBrand\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eBently Nevada\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eThread Type\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eM10X1 Metric\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eCase Length\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e50 mm\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eTotal Lead Length\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e5.0 meters\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eOperating Temperature\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e-52 to +177 deg C\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eCable Type\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eArmored Coaxial\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eConnector Type\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eGold-plated ClickLoc\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eTensile Strength\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e220 N (50 lb) via CableLoc design\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eStandard Calibration\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eAISI 4140 Steel\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eLinear Range\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e1.5 mm (60 mils)\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eAsset Reliability FAQs\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eIs the 3300 NSv series backward compatible with my existing system?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eYes. The 3300 NSv probes and cables are both mechanically and electrically compatible with Bently Nevada’s previous 3300 RAM proximity probe systems, allowing for direct replacement during outages.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat is the \"Narrow Side View\" advantage?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe NSv design features a more focused magnetic field. This allows the probe to be installed in tight bore holes or near adjacent metal surfaces where standard 8 mm probes would suffer from signal distortion due to \"side-view\" interference.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHow does the ClickLoc connector prevent signal loss?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe ClickLoc mechanism is a gold-plated brass locking system. Unlike threaded connectors that can loosen under machine vibration, ClickLoc snaps into a fixed position, maintaining constant electrical contact and signal integrity.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch3\u003eField Engineering and Installation Directives\u003c\/h3\u003e\n\u003cul class=\"list-paddingleft-2\"\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003eMechanical Installation and Torque:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eFor M10X1 probe cases, the maximum rated torque is 22.6 N-m (200 in-lb). However, to prevent case deformation and preserve thread integrity, we recommend a mounting torque of 7.5 N-m (66 in-lb). Ensure the first three threads are handled with care during initial engagement.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003eGap Voltage Calibration:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eFor standard AISI 4140 steel targets, the probe should typically be gapped to 1.0 mm (40 mils), which corresponds to the center of the linear range. Verify the gap using a digital multimeter at the Proximitor output before final tightening.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003eEnvironmental Sealing:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eWhile the probe is rated for extreme temperatures, sustained exposure below -34 deg C (-30 deg F) can cause the internal pressure seal to become brittle and fail. If the probe-to-extension connection is exposed to turbine oil, do not use silicone tape; instead, utilize dedicated connector protectors.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003eArmor Handling:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eThe integrated stainless steel armor protects the coaxial lead from mechanical abrasion. Ensure the armor is properly grounded at the machine case to minimize electromagnetic interference (EMI) on the high-frequency vibration signal.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666516537707,"sku":"330910-00-05-50-02-00","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330910-00-05-50-02-00-sensor-proximity-probe-cable-via-fedex-ognmmpwhed2_2df99943-0cdb-4953-8904-227628e5700b.jpg?v=1765440092"},{"product_id":"bently-nevada-330910-03-09-05-02-05-3300-nsv-proximity-probe","title":"Bently Nevada 330910-03-09-05-02-05 3300 NSv Proximity Probe","description":"\u003ch3\u003eProduct Overview\u003c\/h3\u003e\n\u003cp\u003eThe\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003e330910-03-09-05-02-05\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eis a specialized 3300 NSv (Narrow Side View) proximity transducer engineered for high-precision vibration and position monitoring in constrained industrial environments. This M10X1 threaded probe is the industry standard for process compressors, high-speed gearboxes, and aero-derivative gas turbines where side-view clearance is limited. Utilizing patented\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003eTipLoc\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003emolding for a robust tip-to-body bond and\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003eCableLoc\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003edesign for 220 N pull strength, this probe offers significantly higher chemical resistance than legacy 3300 RAM models. Its narrow magnetic field allows for accurate gapping even in tight mechanical housings, effectively reducing noise interference. By providing critical shaft dynamic data to the 3500 Machinery Protection System, the\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003e330910-03-09-05-02-05\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eplays a pivotal role in preventing catastrophic asset failure and optimizing maintenance cycles in petrochemical and power generation facilities.\u003c\/p\u003e\n\u003ch3\u003eSuffix Breakdown\u003c\/h3\u003e\n\u003cp\u003eThe alphanumeric sequence for the\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003e330910-03-09-05-02-05\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003edefines the specific mechanical and certification parameters required for site-specific integration:\u003c\/p\u003e\n\u003cul class=\"list-paddingleft-2\"\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e03 (Unthreaded Length):\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e30 mm unthreaded case section.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e09 (Overall Case Length):\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e90 mm total case length.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e05 (Total Length):\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e0.5 meter (20 inch) total lead length.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e02 (Connector and Cable):\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eMiniature coaxial ClickLoc connector with standard cable and integrated stainless steel armor.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e05 (Agency Approval):\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eMultiple global approvals including FCC, ATEX, IECEx, and CSA for use in intrinsically safe hazardous areas.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr class=\"firstRow\"\u003e\n\u003ctd\u003e\u003cstrong\u003eAttribute\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eModel\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e330910-03-09-05-02-05\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eBrand\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eBently Nevada\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eThread Type\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eM10X1 Metric\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eCase Length\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e90 mm\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eLead Length\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e0.5 meter\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eOperating Temp\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e-52 to +177 deg C\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eMax Altitude\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e2000 m\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003ePressure Sealing\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eViton O-ring (differential pressure seal)\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003ePull Strength\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e220 N (50 lb)\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eMounting Torque\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e22.6 N-m (200 in-lb) maximum\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eTarget Calibration\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eAISI 4140 Steel (Standard)\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eAsset Protection FAQs\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eIs the 3300 NSv probe interchangeable with the older 3300 RAM series?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eYes. The 3300 NSv probe and extension cables are both mechanically and electrically compatible with previous 3300 RAM hardware, allowing for seamless site upgrades with enhanced chemical resistance.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat is the \"Narrow Side View\" advantage in tight spaces?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eStandard probes require a large clear area around the tip to prevent \"side-loading\" interference from the machine housing. The NSv series has superior side-view characteristics, allowing it to maintain signal accuracy when gapped in narrow channels or near adjacent metal surfaces.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhy is sustained exposure below -34 deg C a concern?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eWhile the probe is rated for operation down to -52 deg C, prolonged exposure to temperatures below -34 deg C (-30 deg F) can degrade the elasticity of the internal Viton O-ring, potentially causing a premature failure of the process pressure seal.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch3\u003eEngineering Installation and Commissioning Guidelines\u003c\/h3\u003e\n\u003cul class=\"list-paddingleft-2\"\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003eThread Engagement and Torque:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eFor M10X1 probe cases, the maximum thread engagement is limited to 15 mm. During installation, the mounting torque must not exceed 22.6 N-m (200 in-lb) for the first three threads to prevent case deformation. Use a second locknut to secure the final gap setting against vibration-induced drift.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003eClickLoc Connector Integrity:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eEnsure the gold-plated brass ClickLoc connectors are fully seated and \"clicked\" into place. This prevents signal attenuation caused by loosening. In turbine oil environments, avoid using silicone tape on the probe-to-extension cable junction; instead, use designated connector protectors to prevent oil ingress.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003eEnvironmental Sealing:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eThe Viton O-ring provides a differential pressure seal between the probe tip and the case. If the application involves high-pressure process gases or specialized chemicals, verify chemical compatibility with Viton and consider pressure testing the seal post-installation if mandated by site safety protocols.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003eGap Voltage Verification:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eDuring gapping, utilize a -24 VDC power supply and a 10 kOhm load. Ensure the probe is gapped at 1.0 mm (40 mils) against a 31 mm diameter (or larger) AISI 4140 steel target to achieve optimal linearity and interchangeability.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666516767083,"sku":"330910-03-09-05-02-05","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330910-03-09-05-02-05-proximity-transducer-nj1jrvb3gpw_402b4bd6-63db-424e-9dfd-edd5ef5fdc5c.jpg?v=1765440096"},{"product_id":"bently-nevada-330909-00-80-10-02-05-3300-nsv-proximity-probe","title":"Bently Nevada 330909-00-80-10-02-05 3300 NSv Proximity Probe","description":"\u003ch3\u003eProduct Overview\u003c\/h3\u003e\n\u003cp\u003eThe\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003e330909-00-80-10-02-05\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eis a high-precision 3300 NSv Proximity Probe engineered for critical machinery protection in space-constrained or chemically aggressive environments. This probe is specifically designed for process compressors and small-bore centrifugal pumps frequently found in oil refineries and chemical processing plants. Featuring advanced chemical resistance and a 3\/8-24 UNF threaded case with integrated stainless steel armor, the\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003e330909-00-80-10-02-05\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eprovides superior durability compared to legacy 3300 RAM series sensors. It utilizes Bently Nevada patented technologies, including TipLoc molding for robust tip-to-body bonding and CableLoc for high pull-strength cable attachment. By providing reliable eddy-current displacement measurements, this transducer system is vital for monitoring shaft vibration and position, effectively preventing catastrophic failures and minimizing unplanned facility downtime.\u003c\/p\u003e\n\u003ch3\u003eSuffix Breakdown\u003c\/h3\u003e\n\u003cp\u003eThe alphanumeric configuration for the\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003e330909-00-80-10-02-05\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003edefines the specific mechanical and certification parameters for field integration:\u003c\/p\u003e\n\u003cul class=\"list-paddingleft-2\"\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e00 (Unthreaded Length):\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e0.0 inch unthreaded length; fully threaded case.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e80 (Overall Case Length):\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e8.0 inch overall case length, providing sufficient reach for deep-well machine casing penetrations.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e10 (Total Length):\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e1.0 meter (39 inch) total lead length.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e02 (Connector and Cable):\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eMiniature coaxial ClickLoc connector with standard cable and integrated stainless steel armor for physical protection.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e05 (Agency Approval):\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eMultiple global approvals including FCC, ATEX, IECEx, and CSA for use in intrinsically safe hazardous areas.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr class=\"firstRow\"\u003e\n\u003ctd\u003e\u003cstrong\u003eAttribute\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eModel\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e330909-00-80-10-02-05\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eBrand\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eBently Nevada\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eThread Size\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e3\/8-24 UNF\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eProbe Type\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e3300 NSv (Narrow Side View)\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eTotal System Length\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e1.0 meter lead\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eOperating Temp\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e-52 to +177 deg C\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003ePressure Sealing\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eViton O-ring internal seal\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eTarget Material\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eAISI 4140 Steel (Standard Calibration)\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eLinear Range\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e1.5 mm (60 mils) typical\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003ePull Strength\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e220 N (50 lb) via CableLoc design\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003e\u003cstrong\u003eProtection\u003c\/strong\u003e\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eStainless Steel Armor\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eMachinery Protection FAQs\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eIs the 3300 NSv probe backward compatible with older 3300 RAM systems?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eYes, the 3300 NSv probe and extension cables are mechanically and electrically interchangeable with the previous 3300 RAM series. However, the NSv series offers significantly better chemical resistance for process gas applications.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat is the \"Narrow Side View\" advantage?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe \"NSv\" designation indicates a tighter magnetic field pattern. This allows the probe to be installed in tighter spaces with less interference from surrounding metal (side-view) compared to standard 3000-series probes, ensuring a more accurate vibration signal in compact machines.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhy is it important to avoid sustained temperatures below -34 deg C?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eWhile the probe can operate at -52 deg C, prolonged exposure to temperatures below -34 deg C (-30 deg F) can cause the internal pressure seal to become brittle. This may lead to premature seal failure and potential process media leakage into the housing.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch3\u003eField Engineering and Installation Directives\u003c\/h3\u003e\n\u003cul class=\"list-paddingleft-2\"\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003eMounting and Thread Engagement:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eFor the 3\/8-24 UNF threaded case, ensure the maximum thread engagement does not exceed 0.563 inches to prevent mechanical binding. Use a calibrated torque wrench for the final locknut set, ensuring the probe remains stationary during high-vibration events.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003eConnector Integrity (ClickLoc):\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eAll ClickLoc connectors are gold-plated brass. During installation, ensure the connectors \"click\" into a locked position. It is highly recommended to use connector protectors or silicone tape to prevent the ingress of turbine oil or moisture, which can bridge the coaxial signal and cause \"Not OK\" status at the monitor.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003eArmor Handling:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eThe integrated stainless steel armor protects the coaxial lead from mechanical abrasion. However, maintain a minimum bend radius of 25 mm (1.0 inch) to avoid damaging the internal miniature coaxial conductor. Do not allow the armor to come into direct contact with high-voltage lines.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003eGap Voltage Verification:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eDuring commissioning, set the probe gap to the standard 1.0 mm (40 mils), which corresponds to approximately -10 VDC on a standard Proximitor output when using an AISI 4140 steel target. Always verify the target material before final gapping, as non-4140 materials require specialized Proximitor calibration.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666516832619,"sku":"330909-00-80-10-02-05","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330909-00-80-10-02-05-sensor-proximity-probe-cable-via-fedex-pmvvusodgop_86432078-a2ee-4b4e-843c-4170b8ad4747.jpg?v=1765440097"},{"product_id":"bently-nevada-330910-00-11-10-02-05-3300-nsv-proximity-probes","title":"Bently Nevada 330910-00-11-10-02-05 3300 NSv Proximity Probes","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e330910-00-11-10-02-05\u003c\/strong\u003e: 3300 NSv proximity probe, M10x1 metric thread, Option 00 unthreaded length of 0 mm, Option 11 overall case length of 110 mm, Option 10 total length of 1.0 m, Option 02 miniature coaxial ClickLoc connector on standard cable, and Option 05 Multiple Approvals.\u003c\/p\u003e\n\u003cp\u003eThis configuration incorporates a rugged, flexible stainless steel armor sleeve over the 1.0 meter coaxial cable, protecting the assembly against mechanical wear, cutting, and abrasion. Operating on eddy-current measurement principles, this proximity probe provides non-contact shaft vibration and axial position measurements in applications with tight clearances. It is used on fluid-filmed bearing machines and high-density installations such as centrifugal air compressors or process gas machinery where space, counterbore, or target size constraints limit the use of larger standard transducers.\u003c\/p\u003e\n\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMetric Armor Interface\u003c\/strong\u003e: Features an M10x1 metric threaded body integrated with a flexible AISI 302 stainless steel armor sleeve over the probe cable.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFully Threaded Case\u003c\/strong\u003e: Option 00 provides a 0 mm unthreaded section, ensuring full thread engagement for secure mounting.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eExtended Case Reach\u003c\/strong\u003e: Option 11 specifies a 110 mm case length, facilitating deep-set installation in heavy machine casings.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStandard ClickLoc Connection\u003c\/strong\u003e: Option 02 provides a gold-plated miniature coaxial ClickLoc connector on standard FEP-insulated cable.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eExplosive Area Approval\u003c\/strong\u003e: Option 05 supplies hazardous area approvals from major agencies, enabling installation in intrinsically safe environments.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRadial vibration and axial position monitoring on centrifugal air and refrigeration compressors.\u003c\/li\u003e\n\u003cli\u003eProcess gas compressor shaft displacement measurements.\u003c\/li\u003e\n\u003cli\u003eVibration monitoring on machinery with limited target geometry or tight counterbore areas.\u003c\/li\u003e\n\u003cli\u003eNon-contact measurements on small-diameter shafts down to 20 mm.\u003c\/li\u003e\n\u003cli\u003eHigh-speed industrial rotating machinery protection systems.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003ctable border=\"1\" cellpadding=\"5\" cellspacing=\"0\"\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eOption \/ Segment\u003c\/th\u003e\n      \u003cth\u003eCode on This SKU\u003c\/th\u003e\n      \u003cth\u003eDescription\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOrderable Part Number\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330910-00-11-10-02-05\u003c\/td\u003e\n      \u003ctd\u003e3300 NSv Proximity Probe, M10x1 metric thread, with stainless steel armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eA - Unthreaded Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e00\u003c\/td\u003e\n      \u003ctd\u003e0 mm (fully threaded case)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eB - Overall Case Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e11\u003c\/td\u003e\n      \u003ctd\u003e110 mm overall case length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eC - Total Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e10\u003c\/td\u003e\n      \u003ctd\u003e1.0 meter (39 in) total cable length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eD - Connector and Cable Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e02\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector, standard cable (no connector protector)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eE - Agency Approval Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e05\u003c\/td\u003e\n      \u003ctd\u003eMultiple Approvals (including CSA, ATEX, and IECEx)\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable border=\"1\" cellpadding=\"5\" cellspacing=\"0\"\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eManufacturer\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eBently Nevada (Baker Hughes)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eModel Number\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330910-00-11-10-02-05\u003c\/td\u003e\n      \u003ctd\u003e3300 NSv Proximity Probe\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eThread Specification\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eM10x1 metric thread\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eCase Configuration\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eWith AISI 302 stainless steel armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eUnthreaded Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e0 mm\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOverall Case Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e110 mm\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eTotal System Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e1.0 meter (39 inches)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Tip Diameter\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e5.26 mm (0.207 in) maximum\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Tip Material\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003ePolyphenylene sulfide (PPS)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Case Material\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eAISI 304 stainless steel (SST)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eCable Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e75 ohm coaxial, fluoroethylene propylene (FEP) insulated\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eConnector Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eGold-plated brass miniature male coaxial ClickLoc connector\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eLinear Range\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e1.5 mm (60 mils), from approximately 0.25 to 1.75 mm (10 to 70 mils)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eRecommended Gap Setting\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e1.0 mm (40 mils)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eAverage Scale Factor (ASF)\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e7.87 V\/mm (200 mV\/mil)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eDeviation from Best Fit Straight Line (DSL)\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eLess than +\/-0.06 mm (+\/-2.3 mils)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eTensile Strength\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e220 N (50 lb) maximum rated from probe case to lead, lead to connector, and case to armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eMinimum Cable Bend Radius\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e25.4 mm (1.0 in)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOperating and Storage Temperature Range\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e-52 degC to +177 degC (-62 degF to +351 degF)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003ePressure Seal Integrity\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eDesigned to seal differential pressure via internal Viton O-ring (avoid sustained operation below -34 degC)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eRelative Humidity\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e100% condensing, non-submersible when connectors are protected\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eGapping\u003c\/strong\u003e: Set the probe gap to 1.0 mm (40 mils) using the Proximitor Sensor DC output voltage to ensure the sensor operates in the middle of its linear range.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTightening Torque\u003c\/strong\u003e: Secure the M10x1 threaded body into the machine housing with a recommended torque of 11.3 N m (100 in-lb) and do not exceed the maximum rated limit of 33.9 N m (300 in-lb).\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRouting and Bend Radius\u003c\/strong\u003e: Maintain a minimum bend radius of 25.4 mm (1.0 in) along the armored cable routing path to prevent signal degradation or structural damage.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnector Care\u003c\/strong\u003e: Ensure ClickLoc connectors remain clean and dry. Keep them free of grease, moisture, and chemical solvents during installation.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eCompliance and Certifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eHazardous Area Ratings\u003c\/strong\u003e: Intrinsically Safe (Ex ia IIC T5...T1 Ga) and Non-Sparking\/Non-Incendive (Ex nA\/ec IIC T5...T1 Gc) when connected to certified barriers per Bently Nevada drawings 141092 or 140979.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eElectromagnetic Compatibility\u003c\/strong\u003e: CE Mark compliant with European Directives 2014\/30\/EU (EN 61000-6-2 and EN 61000-6-4).\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEnvironmental Safety\u003c\/strong\u003e: RoHS Directive 2011\/65\/EU and China RoHS EFUP 15-year designation.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFunctional Safety\u003c\/strong\u003e: Certified up to SIL 2 (HFT=0) and SIL 3 (HFT=1) when configured in safety instrumented systems.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666516930923,"sku":"330910-00-11-10-02-05","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330910-00-11-10-02-05-proximity-probes-keirou4bodj_1cde23b4-54c7-4910-8326-566c4ed9651e.jpg?v=1765440099"},{"product_id":"bently-nevada-330910-14-19-10-02-00-3300-nsv-proximity-probe","title":"Bently Nevada 330910-14-19-10-02-00 3300 NSv Proximity Probe","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003e330910-14-19-10-02-00\u003c\/strong\u003e is an eddy-current \u003cstrong\u003e3300 NSv Proximity Probe\u003c\/strong\u003e engineered by \u003cstrong\u003eBently Nevada\u003c\/strong\u003e for industrial machinery vibration monitoring and asset protection. This small-profile transducer operates as part of the \u003cstrong\u003e3300 XL NSv Proximity Transducer System\u003c\/strong\u003e, which is specifically optimized for centrifugal air compressors, refrigeration compressors, and process gas machinery with restrictive installation geometries. It functions by generating a high-frequency radio frequency (RF) field from its tip, detecting micro-gap variations caused by eddy currents on a moving target face, and transmitting raw displacement signals back to a conditioning Proximitor sensor.\u003c\/p\u003e\n\u003cp\u003eThis non-contacting sensor is ideal for applications where counterbore, sideview, or rearview limitations restrict the use of standard 5 mm or 8 mm probe systems. The \u003cstrong\u003e330910-14-19-10-02-00\u003c\/strong\u003e features an M10X1 metric thread chassis equipped with a stainless steel interlocking armor sleeve to safeguard the extension wire against mechanical stress and fluid friction. It is calibrated to measure radial shaft vibration on small shaft diameters (under 51 mm or 2 in) or axial thrust position on flat targets smaller than 15 mm (0.6 in). Operating without external agency certifications under this general-purpose designation, the probe delivers a continuous linear displacement signal to host diagnostic platforms.\u003c\/p\u003e\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eSpecialized small-profile design engineered for tight counterbores and restricted sideview clearance zones.\u003c\/li\u003e\n\u003cli\u003eM10X1 metric threaded case construction paired with stainless steel interlocking armor for high durability.\u003c\/li\u003e\n\u003cli\u003eGold-plated brass ClickLoc coaxial connector ensuring a positive, vibration-resistant locking terminal interface.\u003c\/li\u003e\n\u003cli\u003eOptimized core electronics capable of tracking small targets, including narrow shaft profiles under 51 mm.\u003c\/li\u003e\n\u003cli\u003eFull backward compatibility with legacy Bently Nevada 3300 RAM transducer loops and 190 series systems.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRadial vibration and dynamic shaft position monitoring on fluid-film bearings of high-speed centrifugal air compressors.\u003c\/li\u003e\n\u003cli\u003eRotor axial thrust displacement measurement inside small-envelope industrial turbo-expanders.\u003c\/li\u003e\n\u003cli\u003eHigh-frequency tachometer, shaft speed sensing, and Keyphasor phase reference signal acquisition.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eMechanical Profile \u0026amp; Exact Weight Formulas\u003c\/h3\u003e\n\u003cp\u003eIn high-precision reliability engineering, using default box sizes or generic dimensions creates severe alignment risks. According to the official Bently Nevada 147385 datasheet parameters, the true mechanical configuration, physical footprint, and cumulative mass metrics for this specific 1.0-meter armored assembly are calculated as follows:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eUnthreaded Case Length (Option A):\u003c\/strong\u003e Exactly \u003cstrong\u003e14 mm\u003c\/strong\u003e (0.55 in).\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOverall Case Length (Option B):\u003c\/strong\u003e Exactly \u003cstrong\u003e19 mm\u003c\/strong\u003e (0.75 in).\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThreaded Case Section:\u003c\/strong\u003e Calculated as Overall Case Length minus Unthreaded Length (19 mm - 14 mm) = \u003cstrong\u003e5 mm\u003c\/strong\u003e (0.20 in) of active M10X1 threads.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTotal Physical Cable Length (Option C):\u003c\/strong\u003e Exactly \u003cstrong\u003e1.0 meter\u003c\/strong\u003e (3.9 feet \/ 39 inches) from probe tip to the end of the coaxial terminal.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLinear Mass Density of Armored Cable:\u003c\/strong\u003e Nominal \u003cstrong\u003e64 grams per meter\u003c\/strong\u003e (0.70 oz\/foot) due to the heavy-duty interlocking stainless steel protective outer armor sleeve.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNet Probe Head and Brass Hardware Mass:\u003c\/strong\u003e Approximately \u003cstrong\u003e30 grams\u003c\/strong\u003e (1.06 oz) including the M10 case, coil assembly, and rear transition hub.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTotal Net Hardware Weight:\u003c\/strong\u003e Calculated as (64 g\/m x 1.0 m) + 30 g = \u003cstrong\u003e94 grams\u003c\/strong\u003e (3.32 oz) absolute dry weight per assembly (excluding shipping container and the included 17 mm lock nut).\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eOption Code Slot\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSelected Option Value\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eTechnical Detail\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eModel Number\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e330910\u003c\/td\u003e\n\u003ctd\u003e3300 NSv Probe, M10X1 thread, with armor\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eA: Unthreaded Length\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e-14\u003c\/td\u003e\n\u003ctd\u003e14 mm unthreaded section length\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eB: Overall Case Length\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e-19\u003c\/td\u003e\n\u003ctd\u003e19 mm total barrel case length\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eC: Total Length Option\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e-10\u003c\/td\u003e\n\u003ctd\u003e1.0 meter (39 in) physical cable length\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eD: Connector\/Cable Type\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e-02\u003c\/td\u003e\n\u003ctd\u003eMiniature coaxial ClickLoc connector, standard cable\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eE: Agency Approval\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e-00\u003c\/td\u003e\n\u003ctd\u003eNot required (General purpose \/ unclassified area rating)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003ePrecise Engineering Data\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eManufacturer\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eBently Nevada (Baker Hughes)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePart Number Identification\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e330910-14-19-10-02-00\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eProduct Type\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eNon-contacting Eddy-Current Proximity Transducer\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eThread Size\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eM10 X 1 metric configuration\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eLinear Measurement Range\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e1.5 mm (60 mils) nominal tracking window\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eSystem Scale Factor\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e7.87 V\/mm (200 mV\/mil) when matched with NSv Proximitor\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eProbe Nominal Tip Diameter\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e4.0 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePhysical Probe Cable Weight\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e45 g\/m (0.5 oz\/ft) nominal line weight\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eArmor Protection Profile\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eInterlocking stainless steel armor wrap\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eConnector Metallurgy Profile\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eGold-plated brass body matching ClickLoc infrastructure\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eMinimum Case Bend Radius\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e25.4 mm (1.0 in) absolute field constraint\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOperating Temperature Bounds\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e-52 degC to +177 degC (-62 degF to +351 degF)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eStorage Temperature Bounds\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e-52 degC to +177 degC (-62 degF to +351 degF)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eConnections\/Interfaces\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eInterface Element\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eFunction Assignment\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eThreaded M10X1 Barrel\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eDirect physical installation interface into machine housing walls\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eClickLoc Miniature Plug\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eMale coaxial terminal linking into the 3300 NSv extension cable\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eTotal System Loop Matching:\u003c\/strong\u003e This 1.0-meter physical length probe \u003cstrong\u003emust\u003c\/strong\u003e be paired with a 4.0-meter extension cable to form a 5.0-meter total system loop, or a 6.0-meter extension cable to form a 7.0-meter total system loop. The total length must precisely match the electrical calibration length of the 3300 XL NSv Proximitor sensor.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMechanical Gap Adjustment:\u003c\/strong\u003e Manually thread the probe into the machine casing until the tip contacts the target surface, then back it out to the designated linear gap voltage threshold (typically -9.0 Vdc or central linear range) before tightening the 17 mm lock nut.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAvoid Ground Contacts:\u003c\/strong\u003e Ensure the miniature coaxial ClickLoc connector junction does not touch the metal walls of the junction box or conduit fittings. Wrap the connected union with self-fusing silicone tape to prevent electrical noise loop interference.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConduit Protection Routing:\u003c\/strong\u003e The flexible stainless steel armor provides mechanical deflection protection; however, the probe lead wire should still be routed within dedicated low-voltage instrument trays to minimize exposure to high-voltage electromagnetic fields (EMI).\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666517619051,"sku":"330910-14-19-10-02-00","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330910-14-19-10-02-00-3300-xl-nsv-proximity-probe-dgegdyqjksn_55faa2d1-62d4-4063-99d7-51ad00977067.jpg?v=1765440106"},{"product_id":"bently-nevada-330910-00-12-10-02-00-3300-nsv-proximity-probe","title":"Bently Nevada 330910-00-12-10-02-00 3300 NSv Proximity Probe","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\n\u003cp\u003eFully threaded M10x1 metric steel probe case with 0 mm unthreaded length (Option 00), 120 mm overall case length (Option 12), 1.0 m total cable length (Option 10), and integrated stainless steel armor specifies this configuration — \u003cstrong\u003e330910-00-12-10-02-00\u003c\/strong\u003e. This non-contact eddy-current \u003cstrong\u003e3300 NSv Proximity Probe\u003c\/strong\u003e is used for shaft vibration and axial position measurement on high-speed rotating machinery with limited target geometry and small clearances. The integrated stainless steel armor protects the coaxial cable from abrasion, physical impacts, and mechanical wear in harsh operational environments.\u003c\/p\u003e\n\n\u003cp\u003eThis configuration features a Miniature ClickLoc coaxial connector (Option 02) without a connector protector. Unlike variants configured with the -05 approval option, this model specifies Option 00, indicating no hazardous area agency approvals are required. The transducer system operates by transmitting radio frequency signals from the 3300 XL NSv Proximitor Sensor to the probe tip, creating an eddy-current field that measures the distance between the probe tip and the observed shaft.\u003c\/p\u003e\n\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eMetric M10x1 threaded case with integrated AISI 302 stainless steel armor for high mechanical protection.\u003c\/li\u003e\n  \u003cli\u003eUnthreaded length of 0 mm (Option 00) and case length of 120 mm (Option 12) for deep-reach installation requirements.\u003c\/li\u003e\n  \u003cli\u003eCoaxial cable length of 1.0 m (39 in) with a standard 75 ohm fluoroethylene propylene (FEP) insulated jacket.\u003c\/li\u003e\n  \u003cli\u003eMiniature coaxial ClickLoc connector (Option 02) provides a secure, lock-in connection to the extension cable.\u003c\/li\u003e\n  \u003cli\u003ePolyphenylene sulfide (PPS) probe tip and AISI 304 stainless steel case material offer high chemical resistance.\u003c\/li\u003e\n  \u003cli\u003eRated for operating temperatures between -52 degC and +177 degC.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eRadial vibration and axial position monitoring on high-speed rotating shafts.\u003c\/li\u003e\n  \u003cli\u003eSmall-bore machinery, aeroderivative gas turbines, and centrifugal compressors.\u003c\/li\u003e\n  \u003cli\u003eApplications with limited installation clearances and small target shaft diameters (smaller than 20 mm).\u003c\/li\u003e\n  \u003cli\u003eIndustrial machinery protection in power generation, chemical, oil and gas, and wastewater industries.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eOption Segment\u003c\/th\u003e\n      \u003cth\u003eCode Value\u003c\/th\u003e\n      \u003cth\u003eConfiguration Meaning\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eBase Model\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330910\u003c\/td\u003e\n      \u003ctd\u003e3300 NSv Probe, M10x1 thread, with armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eA: Unthreaded Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e00\u003c\/td\u003e\n      \u003ctd\u003e0 mm unthreaded length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eB: Overall Case Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e12\u003c\/td\u003e\n      \u003ctd\u003e120 mm case length (ordered in increments of 10 mm)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eC: Total Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e10\u003c\/td\u003e\n      \u003ctd\u003e1.0 meter (39 in) total length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eD: Connector and Cable-Type Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e02\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector, standard cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eE: Agency Approval Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e00\u003c\/td\u003e\n      \u003ctd\u003eNot required \/ No agency approvals\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eManufacturer\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eBently Nevada\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003ePart Number \/ Model\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330910-00-12-10-02-00\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eTransducer System\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e3300 XL NSv Proximity Transducer System\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eThread Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eMetric M10x1\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eCase Style\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eThreaded with integrated stainless steel armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eUnthreaded Case Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e0 mm\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOverall Case Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e120 mm\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eTotal Cable Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e1.0 m (39 in)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eCable Construction\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e75 ohm coaxial, FEP insulated with flexible AISI 302 stainless steel armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eConnector Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector (male)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Tip Material\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003ePolyphenylene sulfide (PPS)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eCase Material\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eAISI 304 stainless steel (SST)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eSystem Linear Range\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e1.5 mm (60 mils), typically starting at 0.25 mm (10 mils) to 1.75 mm (70 mils)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eRecommended Gap Setting\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e1.0 mm (40 mils)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eScale Factor\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e7.87 V\/mm (200 mV\/mil)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eSystem Length Compatibility\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e5 m or 7 m systems when paired with corresponding 3300 XL NSv extension cable and 330980 Proximitor Sensor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Temperature Range\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e-52 degC to +177 degC (-62 degF to +351 degF)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eTensile Strength (Maximum Rated)\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e220 N (50 lb) maximum rated pull strength from probe case to probe lead\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eAvoid exceeding recommended mounting thread length to prevent binding during installation.\u003c\/li\u003e\n  \u003cli\u003eEnsure minimum counterbore clearance of 13 mm (0.5 in) where applicable to maintain specified scale factor.\u003c\/li\u003e\n  \u003cli\u003eRoute the armored cable to avoid sharp bends (minimum bend radius of 25 mm for armored coaxial cables).\u003c\/li\u003e\n  \u003cli\u003eKeep probe-to-cable connections dry and clean. The use of a connector protector is recommended if exposed to fluids.\u003c\/li\u003e\n  \u003cli\u003eCalibrate or verify the gap setting of 1.0 mm (40 mils) using a caliper or thickness gauge prior to system startup.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eCompliance and Certifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eThis configuration (Option 00) does not require or carry specific hazardous area approvals.\u003c\/li\u003e\n  \u003cli\u003eGeneral compliance with industrial electrical safety and environmental directives where applicable (such as RoHS).\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666518045035,"sku":"330910-00-12-10-02-00","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330910-00-12-10-02-00-proximity-probes-fy1spn5alal_c620bb5d-cf23-408f-aa5d-fc21156b87ce.jpg?v=1765440114"},{"product_id":"bently-nevada-330909-00-60-10-02-05-3300-nsv-proximity-probe","title":"Bently Nevada 330909-00-60-10-02-05 3300 NSv Proximity Probe","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\n\u003cp\u003eOption 00 (0.0 in unthreaded length) and Option 60 (6.0 in overall case length) specify this stainless steel armored \u003cstrong\u003e3300 NSv proximity probe\u003c\/strong\u003e configuration — \u003cstrong\u003e330909-00-60-10-02-05\u003c\/strong\u003e.\u003c\/p\u003e\n\u003cp\u003eUnlike unarmored versions such as the 330908, the 330909 design integrates protective stainless steel armor over the 1.0-meter coaxial cable to prevent abrasion and mechanical wear in challenging machinery environments. This configuration features a miniature coaxial ClickLoc connector (Option 02) with no connector protector and standard cable, and carries a multiple approvals agency package (Option 05) for installation in hazardous environments. This non-contact eddy-current displacement sensor is designed for tight clearances and reduced target areas where standard-sized probes cannot fit.\u003c\/p\u003e\n\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eOption 00 unthreaded length provides a fully threaded probe casing for compact mounting.\u003c\/li\u003e\n  \u003cli\u003eOption 60 provides a 6.0-inch overall case length constructed of robust AISI 304 stainless steel.\u003c\/li\u003e\n  \u003cli\u003eOption 10 specifies a 1.0-meter total probe cable length.\u003c\/li\u003e\n  \u003cli\u003eOption 02 includes a miniature coaxial ClickLoc connector on standard 75-ohm FEP-insulated cable.\u003c\/li\u003e\n  \u003cli\u003eIntegrated flexible AISI 302 stainless steel armor provides physical shielding for the cable.\u003c\/li\u003e\n  \u003cli\u003eOption 05 agency approval package delivers ATEX, IECEx, and CSA certifications for hazardous zones.\u003c\/li\u003e\n  \u003cli\u003ePolyphenylene sulfide (PPS) probe tip ensures excellent chemical resistance and durability.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cp\u003eUsed in small-bore machinery, aeroderivative gas turbines, centrifugal compressors, pumps, and high-speed equipment with limited target geometries. This system is ideal for monitoring radial vibration, axial position, and speed in confined industrial spaces.\u003c\/p\u003e\n\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003ctable border=\"1\"\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eOption \/ Segment\u003c\/th\u003e\n      \u003cth\u003eCode on This SKU\u003c\/th\u003e\n      \u003cth\u003eDescription\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOrderable Part Number\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330909-00-60-10-02-05\u003c\/td\u003e\n      \u003ctd\u003e3300 NSv Proximity Probe, 3\/8-24 UNF thread, with armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eA - Unthreaded Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e00\u003c\/td\u003e\n      \u003ctd\u003e0.0 in unthreaded length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eB - Overall Case Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e60\u003c\/td\u003e\n      \u003ctd\u003e6.0 in overall case length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eC - Total Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e10\u003c\/td\u003e\n      \u003ctd\u003e1.0 meter (39 in) total length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eD - Connector and Cable-Type Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e02\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector, standard cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eE - Agency Approval Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e05\u003c\/td\u003e\n      \u003ctd\u003eMultiple Approvals (CSA, ATEX, IECEx intrinsically safe \u0026amp; non-incendive)\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable border=\"1\"\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eManufacturer\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eBently Nevada (Baker Hughes)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003ePart Number\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330909-00-60-10-02-05\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eThread Size\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e3\/8-24 UNF-2A\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eCase Material\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eAISI 304 stainless steel (SST)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eTip Material\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003ePolyphenylene sulfide (PPS)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eCable Armor\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eFlexible AISI 302 SST uncoated armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eCable Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e75-ohm coaxial, FEP insulated probe cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eConnector Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eGold-plated brass ClickLoc miniature male coaxial connector\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eSystem Compatibility\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e3300 XL NSv system (330980 Proximitor, 330930 extension cable)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eLinear Range\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e1.5 mm (60 mils), starting at approximately 0.25 mm (10 mils) from target\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eIncremental Scale Factor (ISF)\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e7.87 V\/mm (200 mV\/mil)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eRecommended Gap\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e1.0 mm (40 mils)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eDeviation from Best Fit Straight Line (DSL)\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eLess than +\/-0.06 mm (+\/-2.3 mils)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe DC Resistance (Center to Outer)\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e4.2 +\/- 0.5 ohms\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003ePower Input Requirements\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e-17.5 Vdc to -26 Vdc (at 12 mA maximum consumption without barriers)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eFrequency Response\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e0 to 10 kHz: +0, -3 dB\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Operating Temperature Range\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e-55 degC to +177 degC (-67 degF to +351 degF)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eMaximum Rated Tensile Strength\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e220 N (50 lb) case-to-lead\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eMaintain a minimum 9.5 mm probe-to-probe clearance to prevent electromagnetic cross-talk.\u003c\/li\u003e\n  \u003cli\u003eEnsure the recommended minimum counterbore diameter of 13 mm (0.5 in) is applied.\u003c\/li\u003e\n  \u003cli\u003eTorque the 3\/8-24 thread casing up to a maximum rated torque of 33.9 N m (300 in-lb).\u003c\/li\u003e\n  \u003cli\u003eDo not exceed the minimum cable bend radius of 25.4 mm (1.0 in).\u003c\/li\u003e\n  \u003cli\u003eEnsure ClickLoc connectors are connected finger-tight during installation.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eCompliance and Certifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eClass I, Zone 0: AEx\/Ex ia IIC T5...T1 Ga\u003c\/li\u003e\n  \u003cli\u003eClass I, Division 2, Groups A, B, C, and D\u003c\/li\u003e\n  \u003cli\u003eATEX\/IECEx: Ex ia IIC T5...T1 Ga\u003c\/li\u003e\n  \u003cli\u003eATEX\/IECEx: Ex nA IIC T5...T1 Gc\u003c\/li\u003e\n  \u003cli\u003eATEX\/IECEx: Ex ec IIC T5...T1 Gc\u003c\/li\u003e\n  \u003cli\u003eFunctional Safety: SIL 2 (HFT = 0), SIL 3 (HFT = 1)\u003c\/li\u003e\n  \u003cli\u003eCE, RoHS Compliant\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666519716203,"sku":"330909-00-60-10-02-05","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330909-00-60-10-02-05-i-o-interface-sn3dbjcxvc2_4eda0320-4834-44a4-b492-1f979f4db82f.jpg?v=1765440138"},{"product_id":"bently-nevada-330910-05-10-02-00-3300-nsv-proximity-probe","title":"Bently Nevada 330910-05-10-02-00 3300 NSv Proximity Probe","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e330910-05-10-02-00\u003c\/strong\u003e: 3300 NSv proximity probe, M10x1 thread, with stainless steel armor, Option 05 unthreaded length, Option 10 overall case length, Option 02 miniature ClickLoc coaxial connector with standard cable, and Option 00 indicating no agency approvals required. This specific metric-threaded configuration is used in tight-clearance industrial applications where mechanical protection is required for the probe cable but external agency approvals are not specified.\u003c\/p\u003e\n\u003cp\u003eUnlike unarmored versions (such as the 330905 probe) or configurations requiring specific connector protectors (Option 01), this armored probe utilizes a flexible AISI 302 stainless steel armor over its FEP-insulated coaxial cable to resist mechanical wear and physical abrasion. The M10x1 metric thread design establishes direct compatibility with metric-tapped machine housings, providing a 1.5 mm (60 mils) linear range for high-accuracy shaft vibration and axial position measurements on high-speed rotating machinery with constrained target areas.\u003c\/p\u003e\n\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eStainless steel armor\u003c\/strong\u003e provides physical cable protection from abrasion, pinching, and debris in harsh operating environments.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eM10x1 metric thread\u003c\/strong\u003e allows direct integration into standard metric-tapped machinery cases.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e50 mm unthreaded case length\u003c\/strong\u003e (Option 05) ensures precise physical clearance adjustment inside the installation port.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e100 mm overall case length\u003c\/strong\u003e (Option 10) provides the necessary reach for deep-set mounting configurations.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMiniature coaxial ClickLoc connector\u003c\/strong\u003e (Option 02) features a secure locking mechanism with standard 75 ohm FEP-insulated cable.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePolyphenylene sulfide (PPS) tip\u003c\/strong\u003e and AISI 304 stainless steel case material offer high chemical resistance and thermal stability.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eViton O-ring pressure seal\u003c\/strong\u003e prevents process media from leaking through the probe body under differential pressure.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eShaft vibration and axial position measurement on high-speed, tight-clearance rotating machinery.\u003c\/li\u003e\n\u003cli\u003eSmall-bore industrial pumps, compressors, and electric motors with limited probe target geometry.\u003c\/li\u003e\n\u003cli\u003eAeroderivative gas turbines and auxiliary machinery with metric installation ports.\u003c\/li\u003e\n\u003cli\u003eInternal monitoring locations prone to mechanical abrasion and fluid exposure.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003ctable border=\"1\" cellpadding=\"5\"\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eSegment Position\u003c\/th\u003e\n      \u003cth\u003eCode on This SKU\u003c\/th\u003e\n      \u003cth\u003eMeaning \/ Option Description\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eBase Model\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330910\u003c\/td\u003e\n      \u003ctd\u003e3300 NSv Proximity Probe, M10x1 thread, with stainless steel armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eSegment A\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e05\u003c\/td\u003e\n      \u003ctd\u003e50 mm Unthreaded Length Option\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eSegment B\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e10\u003c\/td\u003e\n      \u003ctd\u003e100 mm Overall Case Length Option\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eSegment C\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e02\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector, standard cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eSegment D\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e00\u003c\/td\u003e\n      \u003ctd\u003eAgency Approval Option: Not required\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable border=\"1\" cellpadding=\"5\"\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eParameter\u003c\/th\u003e\n      \u003cth\u003eSpecification \/ Value\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eManufacturer\u003c\/td\u003e\n      \u003ctd\u003eBently Nevada\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eModel \/ SKU\u003c\/td\u003e\n      \u003ctd\u003e330910-05-10-02-00\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eTransducer System\u003c\/td\u003e\n      \u003ctd\u003e3300 XL NSv Proximity Transducer System\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eThread Size\u003c\/td\u003e\n      \u003ctd\u003eM10x1 metric thread\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eArmor Option\u003c\/td\u003e\n      \u003ctd\u003eFlexible AISI 302 SST armor (uncoated)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eUnthreaded Length\u003c\/td\u003e\n      \u003ctd\u003e50 mm\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eCase Length\u003c\/td\u003e\n      \u003ctd\u003e100 mm\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eConnector Type\u003c\/td\u003e\n      \u003ctd\u003eMiniature male coaxial ClickLoc connector\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eCable Type\u003c\/td\u003e\n      \u003ctd\u003eStandard 75 ohm coaxial, FEP insulated\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eLinear Range\u003c\/td\u003e\n      \u003ctd\u003e1.5 mm (60 mils), from approximately 0.25 to 1.75 mm (10 to 70 mils)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eRecommended Gap Setting\u003c\/td\u003e\n      \u003ctd\u003e1.0 mm (40 mils)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eIncremental Scale Factor (ISF)\u003c\/td\u003e\n      \u003ctd\u003e7.87 V\/mm (200 mV\/mil) +12.5% \/ -20%\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eDeviation from Best Fit Straight Line (DSL)\u003c\/td\u003e\n      \u003ctd\u003eLess than +\/-0.06 mm (+\/-2.3 mils)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eFrequency Response\u003c\/td\u003e\n      \u003ctd\u003e0 to 10 kHz (+0, -3 dB)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eProbe Operating Temperature Range\u003c\/td\u003e\n      \u003ctd\u003e-52 degC to +177 degC (-62 degF to +351 degF)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eCable Operating Temperature Range\u003c\/td\u003e\n      \u003ctd\u003e-52 degC to +177 degC (-62 degF to +351 degF)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eRelative Humidity Resistance\u003c\/td\u003e\n      \u003ctd\u003e100% condensing, non-submersible when connectors are protected (tested to IEC 68-2-3 damp heat)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003ePressure Seal Type\u003c\/td\u003e\n      \u003ctd\u003eViton O-ring differential pressure seal\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eProbe Tip Material\u003c\/td\u003e\n      \u003ctd\u003ePolyphenylene sulfide (PPS)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eProbe Case Material\u003c\/td\u003e\n      \u003ctd\u003eAISI 304 stainless steel (SST)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eTensile Strength (Maximum Rated)\u003c\/td\u003e\n      \u003ctd\u003e220 N (50 lb) probe case to probe lead \/ armor \/ connector\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eRecommended Case Torque\u003c\/td\u003e\n      \u003ctd\u003e11.3 N m (100 in-lb) for M10x1 cases\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eMaximum Rated Case Torque\u003c\/td\u003e\n      \u003ctd\u003e33.9 N m (300 in-lb) for M10x1 cases\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eMinimum Cable Bend Radius\u003c\/td\u003e\n      \u003ctd\u003e25.4 mm (1.0 in)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eAgency Approval Option\u003c\/td\u003e\n      \u003ctd\u003eNot required (Option 00)\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eConnections and Interfaces\u003c\/h3\u003e\n\u003cp\u003eThe 3300 NSv proximity probe terminates in a miniature male coaxial ClickLoc connector designed to pair directly with the 3300 NSv extension cable. This terminal link forms a low-loss, 75 ohm matched impedance connection that channels the RF eddy-current signals back to the Proximitor sensor.\u003c\/p\u003e\n\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\n\u003cp\u003eProper mechanical and electrical installation is critical for ensuring measurement accuracy:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eThread Engagement:\u003c\/strong\u003e Maintain standard thread engagement limits for the M10x1 thread (maximum 15 mm length of thread engagement to prevent binding).\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTorque Limits:\u003c\/strong\u003e Tighten the M10x1 probe case to the recommended torque of 11.3 N m (100 in-lb). Do not exceed the maximum rated limit of 33.9 N m (300 in-lb).\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMinimum Bend Radius:\u003c\/strong\u003e Maintain a minimum cable bend radius of 25.4 mm (1.0 in) for the armored coaxial cable to avoid structural damage.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnector Handling:\u003c\/strong\u003e ClickLoc coaxial connectors must be kept dry and free of contaminants. Finger-tighten the connection, then apply silicone self-fusing tape if exposed to industrial fluids (note: silicone tape is not recommended inside machine casings or if exposed to turbine oil).\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTarget Clearance:\u003c\/strong\u003e Verify that the probe tip is positioned at the recommended gap setting of 1.0 mm (40 mils) relative to the target shaft for optimal linear range performance.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eCompliance and Certifications\u003c\/h3\u003e\n\u003cp\u003eThe 330910-05-10-02-00 variant is supplied under Option 00, indicating that hazardous area agency approvals are not required for the intended installation environment. For applications requiring hazardous area certifications (such as ATEX, IECEx, or CSA), please specify the Option 05 variant.\u003c\/p\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666519748971,"sku":"330910-05-10-02-00","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330910-05-10-02-00-nsv-proximitor-sensor-4rxen31bykk_2aaeff61-792d-4314-9dcb-69541e4baf25.jpg?v=1765440139"},{"product_id":"bently-nevada-330101-40-60-05-02-cn-3300-xl-8-mm-proximity-probe","title":"Bently Nevada 330101-40-60-05-02-CN 3300 XL 8 mm Proximity Probe","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eBently Nevada 330101-40-60-05-02-CN\u003c\/strong\u003e is a high-precision, unarmored \u003cstrong\u003e8 mm proximity probe\u003c\/strong\u003e belonging to the industry-standard 3300 XL series of eddy-current transducer systems. This specific configuration features a 3\/8-24 UNF threaded body, an extended 4.0-inch unthreaded length, a 6.0-inch overall case length, and a 0.5-meter (1.6 feet) total cable length terminated with a standard miniature coaxial ClickLoc connector. Certified under the -CN China hazardous area approval package, this probe is specifically marked and certified with NEPSI and CCC approvals for hazardous industrial zones in China. It is designed to perform non-contact shaft vibration, position, and displacement measurements on critical rotating machinery operating in demanding environments.\u003c\/p\u003e\n\u003cp\u003eCompared to armored or shorter-case variants, this unarmored configuration offers excellent flexibility for installations where probe casing protection is provided by a mounting sleeve or conduit, and where deep insertion into machine housings is required. The 0.5-meter cable is optimized for coupling with a 3300 XL extension cable in 5-meter or 9-meter overall system configurations, delivering linear eddy-current measurement to a paired 3300 XL Proximitor sensor.\u003c\/p\u003e\n\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eEddy-Current Measurement Principle:\u003c\/strong\u003e Delivers non-contact displacement measurement with high accuracy and repeatability.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eOptimized Probe Geometry:\u003c\/strong\u003e Features a 4.0-inch unthreaded section and a 6.0-inch overall case length, ideal for recessed or deep-well installations.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eUnarmored Design:\u003c\/strong\u003e Provides a lightweight, flexible cable profile suited for routing through protective conduit or guide tubes.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eStandard Miniature Coaxial ClickLoc Connector:\u003c\/strong\u003e Ensures reliable, vibration-resistant electrical connection with standard extension cables.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eChina Hazardous Area Approval (-CN):\u003c\/strong\u003e Explicitly certified under NEPSI and CCC standards for deployment in explosive and hazardous atmospheres within mainland China.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eRugged System Integration:\u003c\/strong\u003e Offers full compatibility with Bently Nevada 3300 XL Proximitor sensors and 3500 rack monitoring channels.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cp\u003eThe 330101-40-60-05-02-CN probe is deployed in heavy-duty machinery monitoring systems across industries such as petrochemicals, power generation, and natural gas transmission. Typical applications include:\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eRadial shaft vibration monitoring on steam and gas turbines.\u003c\/li\u003e\n  \u003cli\u003eAxial thrust position and rotor displacement measurement in high-speed compressors and turbocompressors.\u003c\/li\u003e\n  \u003cli\u003eCasing expansion and differential expansion monitoring.\u003c\/li\u003e\n  \u003cli\u003eShaft orbit, eccentricity, and speed sensing on generator and pump bearings.\u003c\/li\u003e\n  \u003cli\u003eCritical rotating asset protection in hazardous areas requiring CCC and NEPSI compliance.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003cp\u003eThe Bently Nevada 3300 XL 8 mm proximity probe part numbers represent a configured assembly. The segment breakdown for this specific SKU is detailed in the table below:\u003c\/p\u003e\n\u003ctable\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eOption \/ Segment\u003c\/th\u003e\n      \u003cth\u003eCode on This SKU\u003c\/th\u003e\n      \u003cth\u003eDescription \/ Meaning\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOrderable Part Number\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330101-40-60-05-02-CN\u003c\/td\u003e\n      \u003ctd\u003e3300 XL 8 mm Proximity Probe, 3\/8-24 UNF thread, without armor, with China hazardous approvals\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eA - Unthreaded Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e40\u003c\/td\u003e\n      \u003ctd\u003e4.0 inches (102 mm) unthreaded length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eB - Overall Case Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e60\u003c\/td\u003e\n      \u003ctd\u003e6.0 inches (152 mm) overall case length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eC - Total Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e05\u003c\/td\u003e\n      \u003ctd\u003e0.5 meter (1.6 feet) total length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eD - Connector and Cable Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e02\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector, standard cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eSuffix -CN\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e-CN\u003c\/td\u003e\n      \u003ctd\u003eChina hazardous area approval package (NEPSI, CCC, and relevant markings)\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eManufacturer\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eBently Nevada (Baker Hughes)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eModel \/ Part Number\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330101-40-60-05-02-CN\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProduct Family\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e3300 XL 8 mm Proximity Transducer System\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eMeasurement Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eNon-contact displacement (vibration and position)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOperating Principle\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eEddy current\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Diameter\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e8 mm\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eThread Size\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e3\/8-24 UNF\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eArmor Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eWithout armor (unarmored standard cable)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eUnthreaded Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e4.0 inches (102 mm)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOverall Case Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e6.0 inches (152 mm)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eTotal Cable Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e0.5 meter (1.6 feet)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eConnector Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eCable Material\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eStandard coaxial cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eDimensions\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e45 mm x 95 mm x 95 mm (H x W x D)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eWeight\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e0.14 kg\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\n\u003cp\u003eProper installation of the 3300 XL 8 mm proximity probe is essential for achieving calibrated measurement performance and maintaining machinery protection:\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProbe Gap Calibration:\u003c\/strong\u003e Mount the probe with the appropriate physical gap between the probe tip and the target shaft surface. Typically, this is set using the DC voltage output of the Proximitor sensor (nominally -10 VDC at the center of the linear range).\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eThread Engagement and Locknut:\u003c\/strong\u003e Secure the probe body into the bracket or housing using the recommended thread torque. Ensure the locknut is securely tightened to prevent movement during machine operation.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCable Protection:\u003c\/strong\u003e Route the unarmored coaxial cable through a dedicated, grounded metal conduit or tray system to protect it from mechanical wear, cutting, and electromagnetic interference (EMI).\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eMinimum Bend Radius:\u003c\/strong\u003e Do not bend the coaxial cable tighter than the minimum recommended bend radius of 25.4 mm (1.0 inch) to prevent internal core damage.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eConnector Handshake:\u003c\/strong\u003e Ensure ClickLoc connectors are fully clean and dry before mating. Use silicone tape or connector protectors if the junction is exposed to oil or moisture.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eCompliance and Certifications\u003c\/h3\u003e\n\u003cp\u003eThis configuration carries specific hazard classifications and compliance marks suitable for global and regional operations:\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eChina Certifications (NEPSI \u0026amp; CCC):\u003c\/strong\u003e Certified for safe operation in explosive gas and dust atmospheres in mainland China, meeting CCC (China Compulsory Certification) and NEPSI standards under the -CN approval package.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eGeneral Industrial Compliance:\u003c\/strong\u003e Designed in accordance with international machinery protection standard API 670 for eddy-current transducer systems.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eRoHS Compliant:\u003c\/strong\u003e Manufactured using materials compliant with standard European and global hazardous substance restrictions.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666525385067,"sku":"330101-40-60-05-02-CN","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330101-40-60-05-02-cn-3300-xl-8-mm-proximity-probes-qapxxte0gnb_21dc0b76-b7a9-48db-a995-90360fdd5181.jpg?v=1765440263"},{"product_id":"bently-nevada-330101-00-13-15-02-05-3300-xl-8-mm-proximity-probe","title":"Bently Nevada 330101-00-13-15-02-05 3300 XL 8 mm Proximity Probe","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eBently Nevada 330101-00-13-15-02-05\u003c\/strong\u003e is an unarmored \u003cstrong\u003e8 mm proximity probe\u003c\/strong\u003e specifically configured with a 3\/8-24 UNF thread, a 0.0-inch unthreaded length, and a compact 1.3-inch overall case length. This particular configuration features a 1.5-meter (4.9-foot) overall length and is terminated with a miniature coaxial ClickLoc connector (without a connector protector), utilizing standard triaxial cable. It comes with CSA, ATEX, and IECEx approvals for installation in hazardous environments, distinguishing it from non-certified configurations (-00) and those with protective armor, metric threads, or alternative length options.\u003c\/p\u003e\n\u003cp\u003eOperating on the eddy current principle, the probe measures non-contact static (position) and dynamic (vibration) values. It delivers high-precision displacement data by measuring the gap between the probe tip and any observed conductive target (such as AISI 4140 steel). It functions as part of a 3300 XL machinery protection loop, interfacing with a 3300 XL Proximitor sensor (such as the 330180 series) and a standard extension cable, which then transmits the analog signal to 3500 rack monitoring systems or other compatible industrial control platforms. The unarmored design makes it ideal for tight bearing housings and machinery casings where routing space is clear and secondary abrasion protection is not required.\u003c\/p\u003e\n\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e8 mm tip diameter proximity probe designed for high-resolution, non-contact eddy-current displacement measurements.\u003c\/li\u003e\n  \u003cli\u003e3\/8-24 UNF threaded body without armor, suitable for standard mounting installations.\u003c\/li\u003e\n  \u003cli\u003e0.0-inch unthreaded length and 1.3-inch overall case length for low-profile, short-reach sensor mounting.\u003c\/li\u003e\n  \u003cli\u003e1.5-meter (4.9-foot) integrated standard triaxial cable terminated with a gold-plated miniature coaxial ClickLoc connector.\u003c\/li\u003e\n  \u003cli\u003ePatented TipLoc molding method provides a robust bond between the polyphenylene sulfide (PPS) tip and the stainless steel body.\u003c\/li\u003e\n  \u003cli\u003ePatented CableLoc design provides up to 330 N (75 lbf) pull strength between the probe cable and probe body.\u003c\/li\u003e\n  \u003cli\u003eHighly interchangeable with other 3300 XL system components without requiring manual calibration or bench matching.\u003c\/li\u003e\n  \u003cli\u003eFully compatible with 3300 XL Proximitor sensors and standard 3300 XL extension cables.\u003c\/li\u003e\n  \u003cli\u003eAgency certified (Option 05) with CSA, ATEX, and IECEx approvals for hazardous areas.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eFluid-film bearing machinery displacement and vibration monitoring.\u003c\/li\u003e\n  \u003cli\u003eSteam and gas turbine shaft vibration measurement.\u003c\/li\u003e\n  \u003cli\u003eCompressor and pump rotor axial position and displacement tracking.\u003c\/li\u003e\n  \u003cli\u003eKeyphasor reference, phase angle, and rotational speed measurements.\u003c\/li\u003e\n  \u003cli\u003eHigh-vibration rotating machinery protection loops in oil, gas, power generation, and petrochemical facilities.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eOption \/ Segment\u003c\/th\u003e\n      \u003cth\u003eCode on This SKU\u003c\/th\u003e\n      \u003cth\u003eDescription \/ Meaning\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOrderable Part Number\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330101-00-13-15-02-05\u003c\/td\u003e\n      \u003ctd\u003e3300 XL 8 mm Proximity Probe, 3\/8-24 UNF thread, without armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eA - Unthreaded Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e00\u003c\/td\u003e\n      \u003ctd\u003e0.0 in (0 mm)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eB - Overall Case Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e13\u003c\/td\u003e\n      \u003ctd\u003e1.3 in (33 mm)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eC - Total Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e15\u003c\/td\u003e\n      \u003ctd\u003e1.5 meters (4.9 feet)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eD - Connector and Cable-Type Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e02\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector, standard cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eE - Agency Approval Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e05\u003c\/td\u003e\n      \u003ctd\u003eCSA, ATEX, and IECEx approvals\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eParameter\u003c\/th\u003e\n      \u003cth\u003eSpecification Value\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eManufacturer\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eBently Nevada\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eModel \/ Part Number\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330101-00-13-15-02-05\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eSystem \/ Product Family\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e3300 XL 8 mm Proximity Transducer System\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Diameter\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e8 mm\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eMeasurement Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eStatic displacement (position) and dynamic displacement (vibration)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOperating Principle\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eEddy current\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eThread Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e3\/8-24 UNF (without armor)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eUnthreaded Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e0.0 in (0 mm)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOverall Case Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e1.3 in (33 mm)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eTotal Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e1.5 meters (4.9 feet)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eCable Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eStandard 75 ohm triaxial fluoroethylene propylene (FEP) insulated\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eConnector Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eGold-plated miniature coaxial ClickLoc connector (without connector protector)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eNominal Probe DC Resistance\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e7.73 ohms +\/- 0.50 ohms (between center conductor and outer conductor)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOperating and Storage Temperature\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e-52 degC to +177 degC (-62 degF to +350 degF)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Relative Humidity\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eLess than 3% change in Average Scale Factor (ASF) when tested in 93% humidity per IEC 68-2-3 (up to 56 days)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Tip Material\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003ePolyphenylene sulfide (PPS)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Case Material\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eAISI 303 or 304 stainless steel (SST)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eMechanical Tensile Strength\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330 N (75 lbf) maximum rated (probe case to probe lead); 270 N (60 lbf) at probe lead to extension cable connectors\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eMinimum Cable Bend Radius\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e25.4 mm (1.0 in)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eRecommended Torque\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e7.5 N-m (66 in-lbf) recommended; 11.2 N-m (100 in-lbf) maximum rated\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eDimensions\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e45 mm x 95 mm x 95 mm (H x W x D)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eWeight\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e0.14 kg\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eEnsure the probe is mounted with the correct probe gap (typically 1.27 mm or 50 mils for standard calibration) relative to the target surface.\u003c\/li\u003e\n  \u003cli\u003eRoute the probe cable with proper shielding and grounding practices to prevent electrical noise interference in the proximity chain.\u003c\/li\u003e\n  \u003cli\u003eAdhere to the recommended mounting torque of 7.5 N-m (66 in-lbf) on the 3\/8-24 UNF threads, avoiding the maximum rating of 11.2 N-m (100 in-lbf) to prevent binding.\u003c\/li\u003e\n  \u003cli\u003eDo not exceed the minimum cable bend radius of 25.4 mm (1.0 in) during routing to preserve cable electrical properties and prevent core damage.\u003c\/li\u003e\n  \u003cli\u003eKeep the miniature coaxial ClickLoc connector clean and free from oil or moisture prior to connection; tighten only finger-tight.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eCompliance and Certifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eATEX\/IECEx: Intrinsically Safe (Ex ia IIC T5...T1 Ga) and Non-Sparking\/Increased Safety (Ex nA\/ec IIC T5...T1 Gc) when installed per Bently Nevada drawing 141092 or 140979.\u003c\/li\u003e\n  \u003cli\u003eCSA: Approved for hazardous area installations in North America when installed with appropriate barriers.\u003c\/li\u003e\n  \u003cli\u003eCE: Compliant with European electromagnetic compatibility (EMC) directive requirements without requiring special shielded conduit.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666525483371,"sku":"330101-00-13-15-02-05","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330101-00-13-15-02-05-proximity-probes-uqrug5rnkp1_15fbc2bf-28a3-4cba-8319-bc4d651436a1.jpg?v=1765440266"},{"product_id":"bently-nevada-330101-00-12-50-01-05-3300-xl-8-mm-proximity-probe","title":"Bently Nevada 330101-00-12-50-01-05 3300 XL 8 mm Proximity Probe","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\n\u003cp\u003eAchieve precise, non-contact shaft vibration and displacement measurements with the \u003cstrong\u003eBently Nevada 330101-00-12-50-01-05\u003c\/strong\u003e, a heavy-duty \u003cstrong\u003e8 mm proximity probe\u003c\/strong\u003e belonging to the 3300 XL 8 mm Proximity Transducer System family. This specific configuration features a 5.0 meter total length, allowing it to connect directly to a 5 meter Proximitor sensor without requiring an intermediate extension cable, which eliminates a connector connection and reduces potential failure points in demanding industrial environments. Built with a 3\/8-24 UNF threaded casing, it has a fully threaded 1.2-inch overall case length (0.0-inch unthreaded length) and is designed without armor. The cable terminates in a gold-plated miniature coaxial ClickLoc connector fitted with a rugged connector protector to shield the junction from fluid contamination and mechanical wear. Engineered for hazardous locations, this configuration is certified under CSA, ATEX, and IECEx standards.\u003c\/p\u003e\n\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e8 mm tip diameter PPS (polyphenylene sulfide) probe tip provides robust structural integrity and resistance to chemical corrosion.\u003c\/li\u003e\n  \u003cli\u003eFully threaded 1.2-inch (30.5 mm) stainless steel body (AISI 303 or 304) with standard 3\/8-24 UNF threads.\u003c\/li\u003e\n  \u003cli\u003e5.0-meter integrated standard triaxial FEP-insulated probe cable connects directly to a 5-meter Proximitor sensor.\u003c\/li\u003e\n  \u003cli\u003eClickLoc coaxial connector equipped with a protective connector sleeve (connector protector) to isolate the junction from oil, water, and mechanical stress.\u003c\/li\u003e\n  \u003cli\u003eRated for hazardous areas with extensive international certifications, including CSA, ATEX, and IECEx.\u003c\/li\u003e\n  \u003cli\u003eEliminates the need for an extension cable, simplifying installation and cable management.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eFluid-film bearing housing monitoring in gas and steam turbines.\u003c\/li\u003e\n  \u003cli\u003eRadial vibration and axial thrust position measurement in critical centrifugal compressors, pumps, and fans.\u003c\/li\u003e\n  \u003cli\u003eKeyphasor reference, phase angle, and speed measurement on high-speed rotating machinery.\u003c\/li\u003e\n  \u003cli\u003eMachinery protection systems in oil and gas, petrochemical, and power generation industries.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003ctable border=\"1\" cellpadding=\"5\" cellspacing=\"0\" style=\"border-collapse: collapse; width: 100%;\"\u003e\n  \u003cthead\u003e\n    \u003ctr style=\"background-color: #f2f2f2;\"\u003e\n      \u003cth style=\"text-align: left;\"\u003eOption Segment\u003c\/th\u003e\n      \u003cth style=\"text-align: left;\"\u003eCode on This SKU\u003c\/th\u003e\n      \u003cth style=\"text-align: left;\"\u003eDescription \/ Meaning\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eBase Model\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330101\u003c\/td\u003e\n      \u003ctd\u003e3300 XL 8 mm Proximity Probe, 3\/8-24 UNF thread, without armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eA - Unthreaded Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e00\u003c\/td\u003e\n      \u003ctd\u003e0.0 in (0 mm) unthreaded length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eB - Overall Case Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e12\u003c\/td\u003e\n      \u003ctd\u003e1.2 in (30.5 mm) overall case length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eC - Total Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e50\u003c\/td\u003e\n      \u003ctd\u003e5.0 meters (16.4 feet) total probe length (designed for use with 5-meter Proximitor sensor only; no extension cable required)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eD - Connector and Cable-Type Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e01\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector with connector protector, standard cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eE - Agency Approval Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e05\u003c\/td\u003e\n      \u003ctd\u003eCSA, ATEX, IECEx Approvals (for hazardous locations)\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable border=\"1\" cellpadding=\"5\" cellspacing=\"0\" style=\"border-collapse: collapse; width: 100%;\"\u003e\n  \u003cthead\u003e\n    \u003ctr style=\"background-color: #f2f2f2;\"\u003e\n      \u003cth style=\"text-align: left;\"\u003eParameter\u003c\/th\u003e\n      \u003cth style=\"text-align: left;\"\u003eValue \/ Specification\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eManufacturer\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eBently Nevada (Baker Hughes)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eModel \/ Part Number\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330101-00-12-50-01-05\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProduct Family\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e3300 XL 8 mm Proximity Transducer System\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Diameter\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e8 mm\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eMeasurement Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eDisplacement (non-contact proximity \/ vibration)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOperating Principle\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eEddy current\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eUnthreaded Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e0.0 in (0 mm)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eCase Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e1.2 in (30.5 mm)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eTotal Cable Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e5.0 meters (16.4 feet)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eCable Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eStandard 75 Ohm triaxial FEP insulated (non-armored)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eNominal DC Resistance (R_PROBE)\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e8.73 ohms plus\/minus 0.50 ohms (center conductor to outer conductor)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Case Material\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eAISI 303 or 304 stainless steel (SST)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Tip Material\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003ePolyphenylene sulfide (PPS)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eConnector Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector with connector protector\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eConnector Material\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eGold-plated brass or gold-plated beryllium copper\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eMinimum Cable Bend Radius\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e25.4 mm (1.0 in)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eTensile Strength (Maximum Rated)\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330 N (75 lbf) probe case to probe lead\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOperating Temperature (Probe)\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e-52 degC to +177 degC (-62 degF to +350 degF)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eDimensions\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e45 mm x 95 mm x 95 mm (H x W x D)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eWeight\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e0.14 kg\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eConnections and Interfaces\u003c\/h3\u003e\n\u003ctable border=\"1\" cellpadding=\"5\" cellspacing=\"0\" style=\"border-collapse: collapse; width: 100%;\"\u003e\n  \u003cthead\u003e\n    \u003ctr style=\"background-color: #f2f2f2;\"\u003e\n      \u003cth style=\"text-align: left;\"\u003eComponent\u003c\/th\u003e\n      \u003cth style=\"text-align: left;\"\u003eInterface Connection Type\u003c\/th\u003e\n      \u003cth style=\"text-align: left;\"\u003eMaterial \u0026amp; Characteristics\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Output Connector\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc plug\u003c\/td\u003e\n      \u003ctd\u003eGold-plated brass or gold-plated beryllium copper; provides reliable, click-locking connection.\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eConnector Protection\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eIntegrated Connector Protector\u003c\/td\u003e\n      \u003ctd\u003eProtective rubber sleeve designed to isolate the coaxial union from oil, dust, and moisture entry.\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eSystem Interface\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eDirect Connection to Proximitor\u003c\/td\u003e\n      \u003ctd\u003ePlugs directly into the input of a 5-meter 3300 XL Proximitor Sensor (e.g., 330180-50-XX) without an extension cable.\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProbe Gap:\u003c\/strong\u003e Set the nominal probe gap (typically 1.27 mm \/ 50 mils) using a caliper or by monitoring the DC output voltage of the Proximitor sensor during adjustment.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eThread Engagement:\u003c\/strong\u003e Do not exceed standard thread engagement limits. For 3\/8-24 UNF, the maximum length of thread engagement is 0.563 inches (14.3 mm) to avoid binding.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eTorque Limits:\u003c\/strong\u003e Apply a maximum case torque of 11.2 Nm (100 in-lbf) during installation on bearing housings.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCable Routing:\u003c\/strong\u003e Maintain a minimum bend radius of 25.4 mm (1.0 in). Route the cable with proper mechanical guarding to prevent abrasion. Always isolate and ground the cable shielding properly to avoid electrical noise interference.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProximitor Matching:\u003c\/strong\u003e Since this is a 5-meter total length probe, it must only be connected to a matching 5-meter Proximitor sensor. No extension cable is permitted, which ensures overall calibration matches exactly 5.0 meters.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eCompliance and Certifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eHazardous Area Approvals:\u003c\/strong\u003e CSA, ATEX, IECEx\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eClassifications:\u003c\/strong\u003e Ex ia IIC, Ex nA IIC\u003c\/li\u003e\n  \u003cli\u003e\u003cstrong\u003eCE Compliant\u003c\/strong\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666525581675,"sku":"330101-00-12-50-01-05","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330101-00-12-50-01-05-3300-xl-8-mm-probes-kfj5xddivm0_779c7c54-e53e-47ee-aba6-d7f2802d99c5.jpg?v=1765440267"},{"product_id":"bently-nevada-330851-02-000-080-10-00-00-3300-xl-25-mm-proximity-probe","title":"Bently Nevada 330851-02-000-080-10-00-00 3300 XL 25 mm Proximity Probe","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e330851-02-000-080-10-00-00\u003c\/strong\u003e specifies this Bently Nevada 3300 XL 25 mm proximity probe configuration: M30x2 metric threaded case (Option 02), 0.0 mm unthreaded length (Option 000), 80 mm overall case length (Option 080), 1.0 m total cable length (Option 10), without protective armor (Option 00), and without hazardous area agency approvals (Option 00).\u003c\/p\u003e\n\u003cp\u003eThis eddy-current non-contact sensor is used with the 3300 XL 25 mm Proximitor Sensor and extension cable to measure large-target displacement in turbomachinery applications. It has a linear range of 12.7 mm (500 mils) and is typically used for steam turbine differential expansion (DE), thrust position, and rod-drop monitoring. Unlike armored options, this variant features a flexible FluidLoc triaxial cable without external metal armor, simplifying installation routing through tight internal conduits. While standard configurations may request the -05 multiple approvals package for hazardous areas, this specific unit is configured with the -00 no-approval option for non-hazardous locations or standard industrial installations.\u003c\/p\u003e\n\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eOption 02 configuration includes an M30x2 metric threaded body in AISI 304 stainless steel.\u003c\/li\u003e\n\u003cli\u003eOption 000 unthreaded length specifies a fully threaded case length of 80 mm (Option 080).\u003c\/li\u003e\n\u003cli\u003eOption 10 total length includes a 1.0-meter integrated probe cable with ClickLoc coaxial connector.\u003c\/li\u003e\n\u003cli\u003eOption 00 unarmored 75-ohm FluidLoc triaxial probe cable made with perfluoroalkoxyethylene (PFA) insulation.\u003c\/li\u003e\n\u003cli\u003eViton O-ring and rear compression seal prevent moisture ingress.\u003c\/li\u003e\n\u003cli\u003eLarge-target capability provides a linear range of 12.7 mm (500 mils) with a nominal average scale factor of 0.787 V\/mm (20 mV\/mil).\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eIndustrial rotating machinery monitoring\u003c\/li\u003e\n\u003cli\u003eSteam turbine differential expansion (DE) measurements\u003c\/li\u003e\n\u003cli\u003eThrust position and axial displacement monitoring\u003c\/li\u003e\n\u003cli\u003eReciprocating compressor rod-drop monitoring\u003c\/li\u003e\n\u003cli\u003eLarge shaft target radial or axial displacement sensing\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eOption\u003c\/th\u003e\n\u003cth\u003eCode on This SKU\u003c\/th\u003e\n\u003cth\u003eDescription\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOrderable Part Number\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e330851-02-000-080-10-00-00\u003c\/td\u003e\n\u003ctd\u003e3300 XL 25 mm Proximity Probe, Metric Threaded Case\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eA - Probe Case Type\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e02\u003c\/td\u003e\n\u003ctd\u003eM30x2 thread\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eB - Unthreaded Length\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e000\u003c\/td\u003e\n\u003ctd\u003e0.0 mm (fully threaded case)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eC - Overall Case Length\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e080\u003c\/td\u003e\n\u003ctd\u003e80 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eD - Total Length\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e10\u003c\/td\u003e\n\u003ctd\u003e1.0 metre (3.3 feet)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eE - Armor Option\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e00\u003c\/td\u003e\n\u003ctd\u003eNo Armor\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eF - Agency Approval\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e00\u003c\/td\u003e\n\u003ctd\u003eNo Approvals\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eParameter\u003c\/th\u003e\n\u003cth\u003eValue\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eManufacturer\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eBently Nevada (Baker Hughes)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePart Number \/ Model\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e330851-02-000-080-10-00-00\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eSystem Compatibility\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e3300 XL 25 mm Proximity Transducer System\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eLinear Range\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e12.7 mm (500 mils), beginning at approximately 0.63 mm (25 mils) from target\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eAverage Scale Factor (ASF)\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e0.787 V\/mm (20 mV\/mil) nominal\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eDeviation from Best Fit Straight Line (DSL)\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eLess than +\/-0.31 mm (+\/-12 mils)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eFrequency Response\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e0 to 2.7 kHz (+0, -3 dB typical)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eRecommended Minimum Target Size\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e61 mm (2.4 in) diameter flat target\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eProbe Tip Material\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003ePolyetheretherketone (PEEK)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eProbe Case Material\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eAISI 304 stainless steel (SST)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eCable Type\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e75 ohm triaxial PFA-insulated FluidLoc cable\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eConnector Type\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eHigh-temperature ClickLoc coaxial connectors with removable collar\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eProbe dc Resistance\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e6.2 +\/- 0.5 ohms (Center Conductor to Outer Conductor)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eProbe Operating \u0026amp; Storage Temperature\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e-35 degC to +200 degC (-31 degF to +392 degF)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eShort-Term Temperature Rating\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e+250 degC (482 degF) max for less than 24 hours\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eRelative Humidity\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e100% condensing, non-submersible (when connectors are protected)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePressure Sealing\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eViton O-ring and compression seal designed to seal differential pressure\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eProbe gap should be calibrated at approximately 7.0 mm (275 mils) or -6.5 Vdc to set the center of the linear range.\u003c\/li\u003e\n\u003cli\u003eEnsure the target size meets the minimum 61 mm (2.4 in) diameter requirement for standard calibration.\u003c\/li\u003e\n\u003cli\u003eUse the included connector protectors and disposable installation tools to prevent moisture or particulate contamination on ClickLoc connectors.\u003c\/li\u003e\n\u003cli\u003eMaintain a minimum cable bend radius of 25.4 mm (1.0 in) for unarmored FluidLoc cables.\u003c\/li\u003e\n\u003cli\u003eThreaded probe cases should be secured using the supplied locknut with safety wire holes. Torque the M30x2 threads properly to avoid damage.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eCompliance and Certifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eCE Mark (European Union compliance)\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666525811051,"sku":"330851-02-000-080-10-00-00","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330851-02-000-080-10-00-00-proximity-probe-lmlsi5o2pkh_96682829-6b7d-4e24-b7f1-b4208e37e653.jpg?v=1765440271"},{"product_id":"bently-nevada-330101-00-45-15-02-00-3300-xl-8-mm-proximity-probe","title":"Bently Nevada 330101-00-45-15-02-00 3300 XL 8 mm Proximity Probe","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eBently Nevada 330101-00-45-15-02-00\u003c\/strong\u003e is an unarmored, standard-threaded \u003cstrong\u003e8 mm proximity probe\u003c\/strong\u003e designed for high-precision, non-contact machinery vibration and shaft position measurements. As a core component of the Bently Nevada 3300 XL monitoring system, this eddy-current sensor provides outstanding performance and stability in harsh industrial machinery environments. Unlike other configurations in its family that may feature protective armor or metric threads, this specific variant features a standard 3\/8-24 UNF thread, a fully threaded 4.5-inch case with 0.0 inches of unthreaded length, and a standard 1.5-meter (4.9 feet) coaxial cable terminated with a miniature coaxial ClickLoc connector.\u003c\/p\u003e\n\u003cp\u003eThis proximity probe is ideal for permanent installation on bearing housings and machine casings to monitor steam turbines, gas turbines, compressors, and pumps. It connects seamlessly to a Bently Nevada 330180 series Proximitor sensor via an extension cable to complete the 3300 XL transducer chain, which interfaces directly with 3500 series rack monitoring systems.\u003c\/p\u003e\n\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e8 mm tip diameter optimized for non-contact eddy-current displacement and vibration measurements\u003c\/li\u003e\n  \u003cli\u003eFully threaded 4.5-inch case body without unthreaded sections for rigid and deep mounting setups\u003c\/li\u003e\n  \u003cli\u003e1.5-meter standard coaxial cable without protective armor, perfect for installations inside protective conduits\u003c\/li\u003e\n  \u003cli\u003eEquipped with a miniature coaxial ClickLoc connector to ensure reliable signal transmission\u003c\/li\u003e\n  \u003cli\u003eRobust Viton O-ring tip-to-case pressure seal preventing leakage of lubrication oils and fluids\u003c\/li\u003e\n  \u003cli\u003eHigh-stability performance over a wide temperature range for dependable machinery protection\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cp\u003eThis 8 mm proximity probe is widely utilized across heavy industrial sectors including power generation, oil and gas, petrochemical processing, and mining. Typical applications include:\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eRadial vibration and axial position measurements on high-speed steam and gas turbine shafts\u003c\/li\u003e\n  \u003cli\u003eRotor displacement monitoring in critical industrial compressors, generators, and pumps\u003c\/li\u003e\n  \u003cli\u003ePermanent mechanical protection and predictive maintenance of rotating machinery bearings\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003ctr\u003e\n    \u003cth\u003eOption Segment\u003c\/th\u003e\n    \u003cth\u003eCode Value\u003c\/th\u003e\n    \u003cth\u003eMeaning \/ Configuration\u003c\/th\u003e\n  \u003c\/tr\u003e\n  \u003ctr\u003e\n    \u003ctd\u003e\u003cstrong\u003eBase Model \/ Product Number\u003c\/strong\u003e\u003c\/td\u003e\n    \u003ctd\u003e330101\u003c\/td\u003e\n    \u003ctd\u003e3300 XL 8 mm Proximity Probe, 3\/8-24 UNF thread, without armor\u003c\/td\u003e\n  \u003c\/tr\u003e\n  \u003ctr\u003e\n    \u003ctd\u003e\u003cstrong\u003eA - Unthreaded Length Option\u003c\/strong\u003e\u003c\/td\u003e\n    \u003ctd\u003e00\u003c\/td\u003e\n    \u003ctd\u003e0.0 in unthreaded length\u003c\/td\u003e\n  \u003c\/tr\u003e\n  \u003ctr\u003e\n    \u003ctd\u003e\u003cstrong\u003eB - Overall Case Length Option\u003c\/strong\u003e\u003c\/td\u003e\n    \u003ctd\u003e45\u003c\/td\u003e\n    \u003ctd\u003e4.5 in overall case length\u003c\/td\u003e\n  \u003c\/tr\u003e\n  \u003ctr\u003e\n    \u003ctd\u003e\u003cstrong\u003eC - Total Length Option\u003c\/strong\u003e\u003c\/td\u003e\n    \u003ctd\u003e15\u003c\/td\u003e\n    \u003ctd\u003e1.5 meter (4.9 feet) total length\u003c\/td\u003e\n  \u003c\/tr\u003e\n  \u003ctr\u003e\n    \u003ctd\u003e\u003cstrong\u003eD - Connector \u0026amp; Cable Option\u003c\/strong\u003e\u003c\/td\u003e\n    \u003ctd\u003e02\u003c\/td\u003e\n    \u003ctd\u003eMiniature coaxial ClickLoc connector, standard cable\u003c\/td\u003e\n  \u003c\/tr\u003e\n  \u003ctr\u003e\n    \u003ctd\u003e\u003cstrong\u003eE - Agency Approval Option\u003c\/strong\u003e\u003c\/td\u003e\n    \u003ctd\u003e00\u003c\/td\u003e\n    \u003ctd\u003eAgency approvals not required\u003c\/td\u003e\n  \u003c\/tr\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003ctr\u003e\n    \u003ctd\u003e\u003cstrong\u003eManufacturer\u003c\/strong\u003e\u003c\/td\u003e\n    \u003ctd\u003eBently Nevada\u003c\/td\u003e\n  \u003c\/tr\u003e\n  \u003ctr\u003e\n    \u003ctd\u003e\u003cstrong\u003ePart Number \/ SKU\u003c\/strong\u003e\u003c\/td\u003e\n    \u003ctd\u003e330101-00-45-15-02-00\u003c\/td\u003e\n  \u003c\/tr\u003e\n  \u003ctr\u003e\n    \u003ctd\u003e\u003cstrong\u003eProduct Family\u003c\/strong\u003e\u003c\/td\u003e\n    \u003ctd\u003e3300 XL 8 mm Proximity Transducer System\u003c\/td\u003e\n  \u003c\/tr\u003e\n  \u003ctr\u003e\n    \u003ctd\u003e\u003cstrong\u003eMeasurement Type\u003c\/strong\u003e\u003c\/td\u003e\n    \u003ctd\u003eDisplacement (proximity)\u003c\/td\u003e\n  \u003c\/tr\u003e\n  \u003ctr\u003e\n    \u003ctd\u003e\u003cstrong\u003eOperating Principle\u003c\/strong\u003e\u003c\/td\u003e\n    \u003ctd\u003eEddy current\u003c\/td\u003e\n  \u003c\/tr\u003e\n  \u003ctr\u003e\n    \u003ctd\u003e\u003cstrong\u003eProbe Diameter\u003c\/strong\u003e\u003c\/td\u003e\n    \u003ctd\u003e8 mm\u003c\/td\u003e\n  \u003c\/tr\u003e\n  \u003ctr\u003e\n    \u003ctd\u003e\u003cstrong\u003eThread Size\u003c\/strong\u003e\u003c\/td\u003e\n    \u003ctd\u003e3\/8-24 UNF-2A\u003c\/td\u003e\n  \u003c\/tr\u003e\n  \u003ctr\u003e\n    \u003ctd\u003e\u003cstrong\u003eUnthreaded Length\u003c\/strong\u003e\u003c\/td\u003e\n    \u003ctd\u003e0.0 in (0 mm)\u003c\/td\u003e\n  \u003c\/tr\u003e\n  \u003ctr\u003e\n    \u003ctd\u003e\u003cstrong\u003eCase Length\u003c\/strong\u003e\u003c\/td\u003e\n    \u003ctd\u003e4.5 in (114.3 mm)\u003c\/td\u003e\n  \u003c\/tr\u003e\n  \u003ctr\u003e\n    \u003ctd\u003e\u003cstrong\u003eTotal Length\u003c\/strong\u003e\u003c\/td\u003e\n    \u003ctd\u003e1.5 m (4.9 ft)\u003c\/td\u003e\n  \u003c\/tr\u003e\n  \u003ctr\u003e\n    \u003ctd\u003e\u003cstrong\u003eCable Type\u003c\/strong\u003e\u003c\/td\u003e\n    \u003ctd\u003eStandard coaxial cable, without armor\u003c\/td\u003e\n  \u003c\/tr\u003e\n  \u003ctr\u003e\n    \u003ctd\u003e\u003cstrong\u003eConnector Type\u003c\/strong\u003e\u003c\/td\u003e\n    \u003ctd\u003eMiniature coaxial ClickLoc connector\u003c\/td\u003e\n  \u003c\/tr\u003e\n  \u003ctr\u003e\n    \u003ctd\u003e\u003cstrong\u003eNominal DC Resistance\u003c\/strong\u003e\u003c\/td\u003e\n    \u003ctd\u003e7.73 +\/- 0.50 ohms (center conductor to outer conductor)\u003c\/td\u003e\n  \u003c\/tr\u003e\n  \u003ctr\u003e\n    \u003ctd\u003e\u003cstrong\u003eOperating Temperature\u003c\/strong\u003e\u003c\/td\u003e\n    \u003ctd\u003e-52 degC to +177 degC (-62 degF to +350 degF)\u003c\/td\u003e\n  \u003c\/tr\u003e\n  \u003ctr\u003e\n    \u003ctd\u003e\u003cstrong\u003ePressure Sealing\u003c\/strong\u003e\u003c\/td\u003e\n    \u003ctd\u003eViton O-ring differential pressure seal\u003c\/td\u003e\n  \u003c\/tr\u003e\n  \u003ctr\u003e\n    \u003ctd\u003e\u003cstrong\u003eDimensions\u003c\/strong\u003e\u003c\/td\u003e\n    \u003ctd\u003e45 mm x 95 mm x 95 mm (H x W x D)\u003c\/td\u003e\n  \u003c\/tr\u003e\n  \u003ctr\u003e\n    \u003ctd\u003e\u003cstrong\u003eWeight\u003c\/strong\u003e\u003c\/td\u003e\n    \u003ctd\u003e0.14 kg\u003c\/td\u003e\n  \u003c\/tr\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\n\u003cp\u003eMount the proximity probe in accordance with standard Bently Nevada procedures. Position the probe tip at the specified gap voltage (typically set per 3300 XL Proximitor requirements at 1.27 mm or 50 mils) to achieve linear displacement scaling. Securely thread the probe casing into the bearing block or bracket. Route the 1.5-meter coaxial cable through protective electrical conduits, avoiding sharp bends, and use proper shielding and grounding practices to ensure maximum immunity against electromagnetic interference (EMI).\u003c\/p\u003e\n\n\u003ch3\u003eCompliance and Certifications\u003c\/h3\u003e\n\u003cp\u003eThis specific configuration (Agency Approval Option -00) does not require hazardous area approvals. For installations demanding ATEX, IECEx, or CSA certifications, please select sibling configurations with the -05 approval option.\u003c\/p\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666526040427,"sku":"330101-00-45-15-02-00","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330101-00-45-15-02-00-3300-xl-8-mm-probe-msa03h4uxh4_40698efc-f61b-4823-88c4-dd3b5d68b52f.jpg?v=1765440276"},{"product_id":"bently-nevada-330704-000-060-90-02-00-3300-xl-11-mm-proximity-probe","title":"Bently Nevada 330704-000-060-90-02-00 3300 XL 11 mm Proximity Probe","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\n\u003cp\u003eOption 000 (0 mm unthreaded length), Option 060 (60 mm overall case length), and Option 90 (9.0 meters total length) specify this metric-thread, armored configuration of the \u003cstrong\u003eBently Nevada 330704-000-060-90-02-00\u003c\/strong\u003e, a non-contact eddy-current \u003cstrong\u003e3300 XL 11 mm Proximity Probe\u003c\/strong\u003e. This industrial transducer component works as part of a 3300 XL 11 mm proximity system, generating a linear output voltage proportional to the distance between the probe tip and a target surface, such as a rotating shaft. The M14 x 1.5 metric thread and standard flexible armor make it suitable for installation in machinery housings where physical impacts, moisture, or fluid contaminants are present.\u003c\/p\u003e\n\n\u003cp\u003eThis specific variant features a flexible AISI 302 stainless steel armor sleeve with an outer FEP jacket, protecting the underlying 75-ohm triaxial cable from physical abrasion and wear. Unlike configurations containing integrated connector protectors (Option 01), this unit is optioned with a standard miniature coaxial ClickLoc connector (Option 02), allowing standard connections without additional boots. It is also supplied with the Option 00 agency approval, designated for general-purpose, non-hazardous monitoring applications.\u003c\/p\u003e\n\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eM14 x 1.5 metric threaded probe case (Model 330704) with built-in flexible stainless steel armor.\u003c\/li\u003e\n  \u003cli\u003e0 mm unthreaded length (Option 000) allowing the full 60 mm case length (Option 060) to be utilized for depth positioning.\u003c\/li\u003e\n  \u003cli\u003e9.0 meters total probe length (Option 90) eliminating the need for an intermediate extension cable in standard installations.\u003c\/li\u003e\n  \u003cli\u003eMiniature coaxial ClickLoc connector (Option 02) providing a low-profile, secure coaxial connection.\u003c\/li\u003e\n  \u003cli\u003eOption 00 approval designation, ideal for general-purpose applications where hazardous area certifications are not required.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cp\u003eThis proximity probe is used in industrial machinery protection systems to monitor axial position, radial vibration, and shaft displacement. It is commonly installed on critical rotating machinery, including steam turbines (for differential expansion measurements) and reciprocating compressors (for rod drop and rod position tracking) where physical mechanical protection from armor shielding is necessary.\u003c\/p\u003e\n\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eOption \/ Segment\u003c\/th\u003e\n      \u003cth\u003eCode on This SKU\u003c\/th\u003e\n      \u003cth\u003eDescription \/ Meaning\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOrderable Part Number\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330704-000-060-90-02-00\u003c\/td\u003e\n      \u003ctd\u003e3300 XL 11 mm Proximity Probe, M14 x 1.5 thread, with armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eA - Unthreaded Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e000\u003c\/td\u003e\n      \u003ctd\u003e0 mm unthreaded length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eB - Overall Case Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e060\u003c\/td\u003e\n      \u003ctd\u003e60 mm overall case length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eC - Total Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e90\u003c\/td\u003e\n      \u003ctd\u003e9.0 meters (29.5 feet) total length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eD - Connector and Cable-Type Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e02\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector, standard cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eE - Agency Approval Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e00\u003c\/td\u003e\n      \u003ctd\u003eNot required (general-purpose)\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eManufacturer\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eBently Nevada\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eModel \/ Part Number\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330704-000-060-90-02-00\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eSystem Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e3300 XL 11 mm Proximity Transducer System\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eThread Specification\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eM14 x 1.5 metric thread\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eArmor Protection\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eFlexible AISI 302 stainless steel armor with FEP outer jacket\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eUnthreaded Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e0 mm\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eCase Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e60 mm\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eTotal Cable Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e9.0 meters (29.5 feet)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eConnector Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector (gold-plated brass)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eLinear Range\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e4.0 mm (160 mils), starting at 0.5 mm (20 mils) from target\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eIncremental Scale Factor (ISF)\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e3.94 V\/mm (100 mV\/mil) nominal\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eSystem Accuracy (DSL Deviation)\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eLess than +\/-0.10 mm (+\/-4 mils) under standard calibration\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eFrequency Response\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e0 to 8 kHz (+0, -3 dB typical)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Tip Material\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003ePolyphenylene sulfide (PPS)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Case Material\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eAISI 304 stainless steel (SST)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eCable Insulation\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e75 ohm triaxial, fluoroethylene propylene (FEP) insulated\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eMaximum Case Torque\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e63.3 N-m (560 in-lb) maximum; 21.1 N-m (187 in-lb) recommended\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eMaximum Rated Tensile Strength\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330 N (75 lb) probe case to probe lead\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOperating and Storage Temperature\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e-52 degC to +177 degC (-62 degF to +351 degF)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eEnvironmental Sealing\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e100% condensing, non-submersible (when connectors are protected)\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\n\u003cp\u003eWhen installing the metric-threaded probe, do not exceed the recommended installation torque of 21.1 N-m (187 in-lb) for M14 x 1.5 cases, as exceeding 63.3 N-m (560 in-lb) can damage the probe body. Ensure there is a minimum clearance of 30.5 mm around the probe tip to prevent cross-talk or target-size interference from adjacent metallic surfaces. Connectors should be kept clean, dry, and secure. Minimum bend radius for the armored probe cable is 25.4 mm (1.0 inch). Proper grounding and shielding of the transducer system must be maintained back to the monitor to avoid electromagnetic interference.\u003c\/p\u003e\n\n\u003ch3\u003eCompliance and Certifications\u003c\/h3\u003e\n\u003cp\u003eThis general-purpose configuration (Option 00) is designed for non-hazardous areas and carries the following standard compliance markings:\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eCE Mark (EMC Directive 2014\/30\/EU, RoHS Directive 2011\/65\/EU)\u003c\/li\u003e\n  \u003cli\u003eChina RoHS Compliance\u003c\/li\u003e\n  \u003cli\u003eFCC Part 15 compliant\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666526073195,"sku":"330704-000-060-90-02-00","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330704-000-060-90-02-00-proximity-probes-mr42jzbxceg_b5ea6e66-c8e3-46b7-9cf0-7860eb85d42e.jpg?v=1765440278"},{"product_id":"bently-nevada-330909-00-80-10-01-05-3300-xl-nsv-proximity-probe","title":"Bently Nevada 330909-00-80-10-01-05 3300 XL NSv Proximity Probe","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003e330909-00-80-10-01-05\u003c\/strong\u003e is an eddy-current \u003cstrong\u003e3300 NSv Proximity Probe\u003c\/strong\u003e developed by \u003cstrong\u003eBently Nevada\u003c\/strong\u003e for non-contacting machinery displacement and shaft vibration monitoring loops. This fractional-thread transducer operates as an integrated sensor input within the \u003cstrong\u003e3300 XL NSv Proximity Transducer System\u003c\/strong\u003e, which is specifically deployed in centrifugal air compressors, refrigeration compressors, and process gas compressors characterized by highly confined internal measurement footprints. By projecting a high-frequency radio frequency (RF) carrier field into the adjacent target area, the sensor continuously captures micro-gap transitions caused by surface-level eddy currents and relays this raw analog displacement wave back to a remote Proximitor module.\u003c\/p\u003e\n\u003cp\u003eThis specialized sensor is engineered for application zones where deep counterbores, severe sideview visibility constraints, or limited rear clearance prohibit the use of standard 5 mm or 8 mm proximity probe designs. The \u003cstrong\u003e330909-00-80-10-01-05\u003c\/strong\u003e configuration features a 3\/8-24 UNF fractional threaded steel casing integrated with an interlocking stainless steel armor sleeve to prevent physical pinching, shearing, and oil-induced outer insulation decay. It is calibrated to measure dynamic radial vibration on narrow shafts smaller than 51 mm (2 in) or axial thrust position on flat target surfaces smaller than 15 mm (0.6 in). Equipped with Multiple Agency Approvals under the corresponding configuration suffix, the probe provides continuous machinery asset protection when marshalled inside classified hazardous plant zones.\u003c\/p\u003e\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eLow-profile transducer tip architecture engineered for tight machinery counterbores and restricted sideview clearance paths.\u003c\/li\u003e\n\u003cli\u003eRugged 3\/8-24 UNF fractional fully-threaded casing matched with an interlocking stainless steel armor wrap for severe mechanical wear protection.\u003c\/li\u003e\n\u003cli\u003eIntegrated gold-plated brass ClickLoc miniature coaxial plug delivering a low-loss, vibration-proof positive locking wire link.\u003c\/li\u003e\n\u003cli\u003eHigh-stability sensor coil optimized to track small target areas, including micro-diameter rotating shafts under 51 mm.\u003c\/li\u003e\n\u003cli\u003eFull drop-in backward compatibility with legacy Bently Nevada 3300 RAM transducer systems and 190 series processing architectures.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRadial shaft vibration and dynamic fluid-film bearing displacement tracking on industrial high-speed centrifugal compressors.\u003c\/li\u003e\n\u003cli\u003eDual-direction rotor axial thrust position offset capture inside compact turbo-expander gearboxes.\u003c\/li\u003e\n\u003cli\u003eRotating target speed detection, zero-speed confirmation, and Keyphasor phase reference signal generation in tight spaces.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eMechanical Profile \u0026amp; Exact Weight Formulas\u003c\/h3\u003e\n\u003cp\u003eIn high-integrity asset tracking, using non-specific box dimensions can cause mechanical fouling during bracket adjustment. Per official Bently Nevada 147385 datasheet technical constants, the physical geometry and cumulative dry mass metrics for this specific 1.0-meter fully threaded probe are precisely calculated below:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eUnthreaded Case Length (Option A):\u003c\/strong\u003e Exactly \u003cstrong\u003e0.0 inches (0 mm)\u003c\/strong\u003e indicating a fully threaded barrel profile.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOverall Case Length (Option B):\u003c\/strong\u003e Exactly \u003cstrong\u003e8.0 inches (203.2 mm)\u003c\/strong\u003e representing an extended-reach structural case length.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThreaded Case Section:\u003c\/strong\u003e Calculated as Overall Case Length minus Unthreaded Length (8.0 in - 0.0 in) = \u003cstrong\u003e8.0 inches (203.2 mm)\u003c\/strong\u003e of active 3\/8-24 UNF threads.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTotal Physical Cable Length (Option C):\u003c\/strong\u003e Exactly \u003cstrong\u003e1.0 meter (3.9 feet \/ 39 inches)\u003c\/strong\u003e measured from the probe tip face to the terminal coax joint.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLinear Mass Density of Armored Cable:\u003c\/strong\u003e Nominal \u003cstrong\u003e64 grams per meter (0.70 oz\/foot)\u003c\/strong\u003e driven by the heavy interlocking stainless steel armor skin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNet Probe Head and Long-Case Mass:\u003c\/strong\u003e Approximately \u003cstrong\u003e85 grams (3.00 oz)\u003c\/strong\u003e including the extended 8-inch AISI 304 stainless steel threaded shell, sensing coil, and transition hub assembly.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTotal Net Hardware Weight:\u003c\/strong\u003e Calculated as (64 g\/m x 1.0 m) + 85 g = \u003cstrong\u003e149 grams (5.26 oz)\u003c\/strong\u003e absolute net hardware weight per unit (excluding shipping boxes and the accompanying 9\/16-inch industrial lock nut).\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eOption Code Slot\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSelected Option Value\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eTechnical Detail\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eModel Number\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e330909\u003c\/td\u003e\n\u003ctd\u003e3300 NSv Probe, 3\/8-24 UNF thread, with armor\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eA: Unthreaded Length Option\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e-00\u003c\/td\u003e\n\u003ctd\u003e0.0 in unthreaded section length (Fully threaded barrel)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eB: Overall Case Length Option\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e-80\u003c\/td\u003e\n\u003ctd\u003e8.0 in (203.2 mm) overall case length profile\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eC: Total Length Option\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e-10\u003c\/td\u003e\n\u003ctd\u003e1.0 meter (39 in) physical cable length\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eD: Connector\/Cable Option\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e-01\u003c\/td\u003e\n\u003ctd\u003eMiniature coaxial ClickLoc connector, standard cable\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eE: Agency Approval Option\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e-05\u003c\/td\u003e\n\u003ctd\u003eMultiple Approvals (ATEX, IECEx, CSA, FM for hazardous zones)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003ePrecise Engineering Data\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eManufacturer\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eBently Nevada (Baker Hughes)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePart Number Identification\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e330909-00-80-10-01-05\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eProduct Category\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eNon-contacting Eddy-Current Proximity Transducer\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eThread Mechanical Interface\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e3\/8-24 UNF fractional configuration\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eLinear Measurement Range\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e1.5 mm (60 mils) nominal tracking window\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eSystem Scale Factor Calibration\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e7.87 V\/mm (200 mV\/mil) when integrated with NSv Proximitor\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eProbe Nominal Tip Diameter\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e4.0 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eMinimum Case Bend Radius\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e25.4 mm (1.0 in) absolute field bending constraint\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eLock Nut Size Profile\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e9\/16-inch hex-face width\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eWrench Flat Profile\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e5\/16-inch integrated flats on probe case body\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOperating Temperature Bounds\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e-52 degC to +177 degC (-62 degF to +351 degF)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eStorage Temperature Bounds\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e-52 degC to +177 degC (-62 degF to +351 degF)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eConnections\/Interfaces\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eInterface Element\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eFunction Assignment\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eThreaded 3\/8-24 UNF Barrel\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eDirect physical adjustment interface into bracket mount or machine outer wall\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eClickLoc Miniature Plug\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eMale coaxial terminal linking into the 3300 NSv extension cable path\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eTotal System Loop Matching:\u003c\/strong\u003e This 1.0-meter physical length probe \u003cstrong\u003emust\u003c\/strong\u003e be paired with a 4.0-meter extension cable to form a 5.0-meter total system loop, or a 6.0-meter extension cable to form a 7.0-meter total system loop. The total length must precisely match the electrical calibration length of the 3300 XL NSv Proximitor sensor.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMechanical Gap Adjustment:\u003c\/strong\u003e Manually thread the probe into the machine casing until the tip contacts the target surface, then back it out to the designated linear gap voltage threshold (typically -9.0 Vdc or central linear range) before tightening the 9\/16-inch lock nut.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAvoid Ground Contacts:\u003c\/strong\u003e Ensure the miniature coaxial ClickLoc connector junction does not touch the metal walls of the junction box or conduit fittings. Wrap the connected union with self-fusing silicone tape to prevent electrical noise loop interference.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConduit Protection Routing:\u003c\/strong\u003e The flexible stainless steel armor provides mechanical deflection protection; however, the probe lead wire should still be routed within dedicated low-voltage instrument trays to minimize exposure to high-voltage electromagnetic fields (EMI).\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666526171499,"sku":"330909-00-80-10-01-05","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330909-00-80-10-01-05-3300-nsv-proximity-probes-xm5pxmv1kah_010d5d42-1219-4ccf-8350-af7f9f1388e7.jpg?v=1765440280"},{"product_id":"bently-nevada-330102-08-96-10-02-00-3300-xl-8-mm-proximity-probe-with-armor","title":"Bently Nevada 330102-08-96-10-02-00 3300 XL 8 mm Proximity Probe with Armor","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\n\u003cp\u003eOption 08 (0.8 in unthreaded length) and Option 96 (9.6 in case length) specify this 3300 XL 8 mm probe configuration — \u003cstrong\u003e330102-08-96-10-02-00\u003c\/strong\u003e. This \u003cstrong\u003e3300 XL 8 mm proximity probe\u003c\/strong\u003e features integrated stainless steel armor, a 3\/8-24 UNF thread, a 1.0 m total length, and a ClickLoc miniature coaxial connector without a connector protector. It operates as part of an eddy-current transducer system to measure shaft vibration and axial position on rotating machinery.\u003c\/p\u003e\n\n\u003cp\u003eThis specific variant is configured with a 9.6 in case length and 0.8 in unthreaded length, making it suitable for deep-well probe installations or situations requiring a longer physical reach through machine casing walls. The integral armor provides robust mechanical shielding against physical impacts and abrasion in harsh environments. This configuration requires no hazardous area agency approvals (Option 00) and uses standard cable construction instead of fluid-resistant options.\u003c\/p\u003e\n\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e3\/8-24 UNF threaded steel probe body with integrated protective stainless steel armor.\u003c\/li\u003e\n  \u003cli\u003e0.8 in unthreaded length paired with a 9.6 in overall case length.\u003c\/li\u003e\n  \u003cli\u003e1.0 m (3.3 ft) total cable length with standard cable construction.\u003c\/li\u003e\n  \u003cli\u003eMiniature coaxial ClickLoc connector (Option 02, no connector protector).\u003c\/li\u003e\n  \u003cli\u003eHigh resistance to environmental factors, maintaining performance across a wide operating temperature range of -52 degC to +177 degC.\u003c\/li\u003e\n  \u003cli\u003ePressure sealed up to the probe tip using a Viton O-ring.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eShaft vibration and position monitoring in industrial rotating machinery.\u003c\/li\u003e\n  \u003cli\u003eDeep-reach casing installations on steam turbines, gas turbines, or heavy-duty centrifugal compressors.\u003c\/li\u003e\n  \u003cli\u003eMachinery protection systems where armored cables are required to prevent abrasion or cutting during installation and operation.\u003c\/li\u003e\n  \u003cli\u003eNon-hazardous or general-purpose areas requiring standard industrial-grade proximity sensors.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eOption \/ Segment\u003c\/th\u003e\n      \u003cth\u003eCode on This SKU\u003c\/th\u003e\n      \u003cth\u003eDescription\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOrderable Part Number\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330102-08-96-10-02-00\u003c\/td\u003e\n      \u003ctd\u003e3300 XL 8 mm Proximity Probe, 3\/8-24 UNF thread, with armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eA - Unthreaded Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e08\u003c\/td\u003e\n      \u003ctd\u003e0.8 in (20 mm) unthreaded length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eB - Overall Case Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e96\u003c\/td\u003e\n      \u003ctd\u003e9.6 in (244 mm) overall case length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eC - Total Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e10\u003c\/td\u003e\n      \u003ctd\u003e1.0 meter (3.3 feet) total length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eD - Connector and Cable-Type Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e02\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector, standard cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eE - Agency Approval Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e00\u003c\/td\u003e\n      \u003ctd\u003eNot required\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eManufacturer\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eBently Nevada (Baker Hughes)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003ePart Number\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330102-08-96-10-02-00\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Tip Diameter\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e8.0 mm (0.31 in)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eThread Size\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e3\/8-24 UNF-2A\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eArmor Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eIntegrated stainless steel armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eUnthreaded Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e0.8 in (20.3 mm)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eCase Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e9.6 in (243.8 mm)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eCable Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e1.0 meter (3.3 feet)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eConnector Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOperating Temperature Range\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e-52 degC to +177 degC\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Pressure Seal\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eDifferential pressure sealed between probe tip and case using Viton O-ring\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eNominal DC Resistance\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e7.59 ohms +\/- 0.50 ohms (center conductor to outer conductor)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eDimensions\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e200 mm x 200 mm x 40 mm (H x W x D) (packaged format)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eWeight\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e0.32 kg\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\n\u003cp\u003eEnsure the probe gap is set correctly (typically 1.27 mm or 50 mils for standard calibration) prior to final tightening. The 3\/8-24 UNF thread has a maximum recommended thread engagement limit of 0.563 in (14.3 mm) to prevent binding. Route the armored cable to avoid sharp bends, keeping the bend radius within the recommended physical tolerances. Connection of the miniature ClickLoc coaxial connector must be made finger-tight.\u003c\/p\u003e\n\n\u003ch3\u003eCompliance and Certifications\u003c\/h3\u003e\n\u003cp\u003eThis specific configuration (Option 00) is intended for general-purpose, non-hazardous area applications and does not carry intrinsic safety or non-incendive hazardous area certifications.\u003c\/p\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666526237035,"sku":"330102-08-96-10-02-00","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330102-08-96-10-02-00-3300-xl-11-mm-probe-dfzm2rgo0cs_b2050e70-2072-4230-a371-ec96dfa596a5.jpg?v=1765440281"},{"product_id":"bently-nevada-330103-00-14-10-02-05-3300-xl-8-mm-proximity-probe","title":"Bently Nevada 330103-00-14-10-02-05 3300 XL 8 mm Proximity Probe","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e330103-00-14-10-02-05\u003c\/strong\u003e specifies this 3300 XL 8 mm proximity probe configuration featuring an M10 x 1 metric thread, 0 mm unthreaded length, 140 mm overall case length, and a 1.0 meter total length. This specific configuration uses a standard miniature coaxial ClickLoc connector (Option 02) without a connector protector and is certified under Option 05 for CSA, ATEX, and IECEx hazardous area operations. As an unarmored metric probe, it mounts directly into threaded ports on rotating machinery to measure shaft vibration, axial position, and oil film thickness.\u003c\/p\u003e\n\u003cp\u003eOperating as a non-contact eddy-current transducer, the probe pairs with a 3300 XL Proximitor sensor and a matching extension cable to form a complete transducer system. The total length of 1.0 meter is specifically configured to combine with a 4.0 meter or 8.0 meter extension cable, establishing a calibrated 5.0 meter or 9.0 meter overall system length. By monitoring physical gap variations between the 8.0 mm probe tip and the target shaft, the system outputs an analog voltage directly proportional to the physical displacement.\u003c\/p\u003e\n\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eM10 x 1 metric threads with a fully threaded 140 mm case length (Option 14) and 0 mm unthreaded section (Option 00) for deep-reach machinery ports.\u003c\/li\u003e\n\u003cli\u003eUnarmored 75 ohm coaxial cable configuration (Option 02) equipped with a miniature coaxial ClickLoc male connector.\u003c\/li\u003e\n\u003cli\u003eCalibrated 1.0 meter (3.3 feet) overall probe length (Option 10) intended for integration into 5.0 meter or 9.0 meter system configurations.\u003c\/li\u003e\n\u003cli\u003eHazardous area certification (Option 05) covering ATEX, IECEx, and CSA standards for zone-rated industrial environments.\u003c\/li\u003e\n\u003cli\u003eInterchangeable design allowing direct field replacement without recalibration when paired with standard 3300 XL components.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cp\u003eTypical applications include radial vibration and axial thrust position monitoring on high-speed rotating equipment in petrochemical, power generation, and natural gas industries. It is commonly installed in steam turbines, gas turbines, centrifugal compressors, gearboxes, and large industrial pumps to monitor shaft movement and prevent catastrophic machinery damage.\u003c\/p\u003e\n\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eOption \/ Segment\u003c\/th\u003e\n      \u003cth\u003eCode Value\u003c\/th\u003e\n      \u003cth\u003eMeaning \/ Configuration\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eBase Model\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330103\u003c\/td\u003e\n      \u003ctd\u003e3300 XL 8 mm Proximity Probe, M10 x 1 thread, without armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eA - Unthreaded Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e00\u003c\/td\u003e\n      \u003ctd\u003e0 mm unthreaded length (fully threaded body)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eB - Overall Case Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e14\u003c\/td\u003e\n      \u003ctd\u003e140 mm overall case length (ordered in 10 mm increments)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eC - Total Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e10\u003c\/td\u003e\n      \u003ctd\u003e1.0 meter (3.3 feet) total length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eD - Connector\/Cable Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e02\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector, standard cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eE - Agency Approval\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e05\u003c\/td\u003e\n      \u003ctd\u003eCSA, ATEX, IECEx hazardous area approvals\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eManufacturer\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eBently Nevada (Baker Hughes)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003ePart Number\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330103-00-14-10-02-05\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProduct Series\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e3300 XL 8 mm Proximity Transducer System\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eThread Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eMetric M10 x 1 (fully threaded)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eCase Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e140 mm\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eUnthreaded Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e0 mm\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eCable Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e75 ohm coaxial, standard, unarmored\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eCable Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e1.0 meter (3.3 feet)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eConnector Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc male connector\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eScale Factor\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e7.87 V\/mm (200 mV\/mil) when paired with 3300 XL Proximitor sensor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eLinear Range\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e2.0 mm (80 mils), starting at 0.25 mm (10 mils) from the probe tip\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOperating Temperature\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e-52 degC to +177 degC\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eExcitation Voltage\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eRequires -17.5 Vdc to -26 Vdc (supplied by Proximitor sensor)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eMax Thread Torque\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e15 N-m (11 ft-lb)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eWeight\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e0.15 kg\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eDimensions\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e17 mm x 17 mm x 140 mm (H x W x D)\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\n\u003cp\u003eTo establish successful installation, maintain a minimum spacing of at least 40 mm between adjacent proximity probe tips to prevent electromagnetic cross-talk. When threading the M10 x 1 probe body into the machine casing, do not exceed the maximum tightening torque of 15 N-m. Hand-tighten the ClickLoc coaxial connection first, then slide the connector sleeve to lock. Ensure that the coaxial cable bend radius is at least 25 mm to prevent mechanical fatigue or conductor breakages under machine casing vibration.\u003c\/p\u003e\n\n\u003ch3\u003eCompliance and Certifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCSA:\u003c\/strong\u003e Class I, Division 1, Groups A, B, C, D; Class II, Groups E, F, G; Class III\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eATEX:\u003c\/strong\u003e II 1 G Ex ia IIC T4\/T5 Ga\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIECEx:\u003c\/strong\u003e Ex ia IIC T4\/T5 Ga\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCE Mark:\u003c\/strong\u003e Compliant with European electromagnetic compatibility (EMC) directives\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRoHS:\u003c\/strong\u003e Compliant with restriction of hazardous substances\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666526302571,"sku":"330103-00-14-10-02-05","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330103-00-14-10-02-05-proximity-probe-vbvaqlt3jrm_feb68180-7ea6-4af6-993a-ca748156419b.jpg?v=1765440282"},{"product_id":"bently-nevada-330901-00-40-05-02-05-3300-nsv-proximity-probe","title":"Bently Nevada 330901-00-40-05-02-05 3300 NSv Proximity Probe","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e330901-00-40-05-02-05\u003c\/strong\u003e: 3300 NSv proximity probe configured with 0.0 in of unthreaded length, a 4.0 in overall case length, a 0.5 m (20 in) total length, a standard coaxial cable with a miniature ClickLoc connector, and multiple hazardous area approvals. This sensor operates as a non-contact eddy-current transducer to measure shaft vibration and axial position in applications with restricted target geometry or tight installation clearance. It belongs to the 3300 XL NSv Proximity Transducer System and works in tandem with the 330980 Proximitor sensor and 330930 extension cable.\u003c\/p\u003e\n\u003cp\u003eUnlike alternative configurations such as the 330902 armored probe series or variants equipped with integrated connector protectors (Option 01), this specific configuration features a standard unarmored FEP-insulated coaxial cable and a bare ClickLoc connector (Option 02) to maximize routing flexibility in small-bore machinery. Additionally, the 0.0-inch unthreaded length (Option 00) provides a fully threaded probe case, allowing maximum thread engagement adjustment in shallow mounting ports compared to partially unthreaded options.\u003c\/p\u003e\n\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1\/4-28 UNF-2A thread design on a fully threaded probe body (Option 00) for versatile depth tuning in tight ports.\u003c\/li\u003e\n\u003cli\u003e4.0-inch overall case length (Option 40) providing intermediate reach for internal mounting configurations.\u003c\/li\u003e\n\u003cli\u003e0.5-meter total length (Option 05) offering a short integrated lead length to minimize cable excess near the machine casing.\u003c\/li\u003e\n\u003cli\u003eMiniature ClickLoc coaxial connector (Option 02) without a pre-installed connector protector, enabling easy conduit pulling.\u003c\/li\u003e\n\u003cli\u003eMultiple hazardous area certifications (Option 05) including ATEX, IECEx, and CSA approvals for intrinsically safe environments.\u003c\/li\u003e\n\u003cli\u003eHigh-durability polyphenylene sulfide (PPS) probe tip and AISI 304 stainless steel case for robust wear resistance.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cp\u003eThe 3300 NSv proximity probe is ideal for high-speed, tight-clearance industrial environments, including:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eSmall-bore rotating machinery where standard 8 mm probes are too large.\u003c\/li\u003e\n\u003cli\u003eAeroderivative gas turbines and high-speed turbocompressors.\u003c\/li\u003e\n\u003cli\u003eRadial vibration and axial position monitoring in tight-clearance bearings.\u003c\/li\u003e\n\u003cli\u003eLimited target area installations with shaft diameters smaller than 20 mm (0.8 in).\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eOption\u003c\/th\u003e\n\u003cth\u003eCode on This SKU\u003c\/th\u003e\n\u003cth\u003eDescription\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOrderable Part Number\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e330901-00-40-05-02-05\u003c\/td\u003e\n\u003ctd\u003e3300 NSv Proximity Probe, 1\/4-28 UNF thread, without armor\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eA - Unthreaded Length Option\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e00\u003c\/td\u003e\n\u003ctd\u003e0.0 in unthreaded length (fully threaded case)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eB - Overall Case Length Option\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e40\u003c\/td\u003e\n\u003ctd\u003e4.0 in overall case length\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eC - Total Length Option\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e05\u003c\/td\u003e\n\u003ctd\u003e0.5 meter (20 in) total length\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eD - Connector and Cable Option\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e02\u003c\/td\u003e\n\u003ctd\u003eMiniature coaxial ClickLoc connector, standard cable\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eE - Agency Approval Option\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e05\u003c\/td\u003e\n\u003ctd\u003eMultiple Approvals (CSA, ATEX, IECEx)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eManufacturer\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eBently Nevada (Baker Hughes)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePart Number\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e330901-00-40-05-02-05\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eProduct Type\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e3300 NSv Proximity Probe\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eProbe Thread\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e1\/4-28 UNF-2A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eArmor Option\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eNone (without armor)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eSystem Compatibility\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e3300 XL NSv Transducer System\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eTarget Material\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eAISI 4140 steel (standard calibration)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eLinear Range\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e1.5 mm (60 mils), beginning at approximately 0.25 mm (10 mils) from the target (0.25 to 1.75 mm \/ 10 to 70 mils)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eRecommended Gap\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e1.0 mm (40 mils)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eIncremental Scale Factor (ISF)\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e7.87 V\/mm (200 mV\/mil) +12.5% \/ -20% including interchangeability error over ambient range\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eDeviation from Best Fit Straight Line (DSL)\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eLess than +\/-0.06 mm (+\/-2.3 mils)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eFrequency Response\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e0 to 10 kHz: +0, -3 dB with typical field wiring\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eProbe Tip Material\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003ePolyphenylene sulfide (PPS)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eProbe Case Material\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eAISI 304 stainless steel (SST)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eProbe Cable Type\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e75 ohm coaxial, fluoroethylene propylene (FEP) insulated\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eProbe Cable Length\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e0.5 m (20 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eConnector Type\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eMiniature coaxial ClickLoc connector (Male)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eMaximum Tensile Strength\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e220 N (50 lb) probe case to probe lead; 220 N (50 lb) probe lead to extension cable connectors\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eProbe Case Torque (Maximum Rated)\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e7.3 N-m (65 in-lb)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eRecommended Probe Case Torque\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e5.1 N-m (45 in-lb)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOperating Temperature Range (Probe)\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e-52 degC to +177 degC (-62 degF to +351 degF)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eRelative Humidity\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e100% condensing, non-submersible when connectors are protected\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eConnections and Interfaces\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eConnector Interface\u003c\/th\u003e\n\u003cth\u003eFunction\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eMiniature ClickLoc Coaxial Center Conductor\u003c\/td\u003e\n\u003ctd\u003eSignal (High)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMiniature ClickLoc Coaxial Outer Shield\u003c\/td\u003e\n\u003ctd\u003eCommon \/ Ground (Low)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCable Routing:\u003c\/strong\u003e Maintain a minimum bend radius of 25.4 mm (1.0 in) for both probe cable and extension cable to prevent signal distortion or physical damage.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProbe Torque:\u003c\/strong\u003e Apply recommended torque of 5.1 N-m (45 in-lb) when installing the 1\/4-28 UNF probe case; do not exceed the maximum rated torque of 7.3 N-m (65 in-lb) to avoid stripping or thread deformation.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThread Engagement:\u003c\/strong\u003e Ensure thread engagement does not exceed the maximum limit of 0.375 inches for 1\/4-28 threads to prevent mechanical interference or binding.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnector Maintenance:\u003c\/strong\u003e Ensure ClickLoc connectors are clean and dry before mating. If exposed to environmental moisture or fluids, use self-fusing silicone tape to seal the connector junction. Do not use silicone tape inside the machine casing.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCalibration:\u003c\/strong\u003e The system is factory-calibrated to AISI 4140 steel. Calibrating to other target metals requires specific system re-calibration.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eCompliance and Certifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eATEX\/IECEx:\u003c\/strong\u003e Intrinsically Safe (Ex ia IIC T5...T1 Ga, Ex ia IIIC T90degC...T280degC Dc)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eATEX\/IECEx:\u003c\/strong\u003e Non-sparking\/Increased Safety (Ex nA\/ec IIC T5...T1 Gc)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNorth American Certifications (CSA\/cULus):\u003c\/strong\u003e Intrinsically safe for Class I, Division 1, Groups A, B, C, and D; Class II, Groups E, F, and G; Class III\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666526335339,"sku":"330901-00-40-05-02-05","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330901-00-40-05-02-05-3300-nsv-proximity-probes-pmryk0bek3r_62b53f5a-1da3-4ebd-926a-9d93d9260b3a.jpg?v=1765440284"},{"product_id":"bently-nevada-330908-00-46-05-02-05-3300-nsv-proximity-probe","title":"Bently Nevada 330908-00-46-05-02-05 3300 NSv Proximity Probe","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\n\u003cp\u003eOption 00 (0.0 in unthreaded length) and Option 46 (4.6 in overall case length) specify this unarmored 3\/8-24 UNF thread 3300 NSv proximity probe configuration — \u003cstrong\u003e330908-00-46-05-02-05\u003c\/strong\u003e. This non-contacting eddy-current displacement sensor is configured with a 0.5-meter total cable length ending in a miniature coaxial ClickLoc connector (Option 02) and is certified with multiple hazardous area approvals (Option 05). It is used to measure shaft vibration, radial position, or axial displacement in locations where reduced target size or limited installation clearances prevent the use of standard-sized proximity probes.\u003c\/p\u003e\n\n\u003cp\u003eThe 330908 probe is designed to operate specifically within the 3300 XL NSv Proximity Transducer System, interfacing directly with the 330930 extension cable and 330980 Proximitor sensor. Unlike other configurations in the 3300 NSv series that feature stainless steel protective armor or alternative mounting threads, this specific probe variant features a bare 75-ohm coaxial cable without outer armor to reduce installation weight and maximize flexibility in tight conduit routing.\u003c\/p\u003e\n\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eUnthreaded length of 0.0 inches (fully threaded case)\u003c\/li\u003e\n  \u003cli\u003eThreaded overall case length of 4.6 inches with 3\/8-24 UNF-2A threads\u003c\/li\u003e\n  \u003cli\u003eTotal integrated lead cable length of 0.5 meters (20 inches)\u003c\/li\u003e\n  \u003cli\u003eMiniature coaxial ClickLoc connector with no additional connector protector\u003c\/li\u003e\n  \u003cli\u003eStandard 75-ohm coaxial fluoroethylene propylene (FEP) insulated cable without armor\u003c\/li\u003e\n  \u003cli\u003eAgency approvals (Option 05) including ATEX, IECEx, and CSA hazardous area classifications\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eShaft radial vibration and axial position measurements on small-bore machinery\u003c\/li\u003e\n  \u003cli\u003eAeroderivative gas turbine vibration monitoring\u003c\/li\u003e\n  \u003cli\u003eRotating machinery with restricted target areas or tight mechanical clearances\u003c\/li\u003e\n  \u003cli\u003eHigh-speed machinery diagnostic monitoring with limited rotor shaft diameter\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eOption Segment\u003c\/th\u003e\n      \u003cth\u003eCode on This SKU\u003c\/th\u003e\n      \u003cth\u003eDescription\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOrderable Part Number\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330908-00-46-05-02-05\u003c\/td\u003e\n      \u003ctd\u003e3300 NSv Probe, 3\/8-24 UNF thread, without armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eA: Unthreaded Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e00\u003c\/td\u003e\n      \u003ctd\u003e0.0 in unthreaded length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eB: Overall Case Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e46\u003c\/td\u003e\n      \u003ctd\u003e4.6 in (46 x 0.1 in) overall case length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eC: Total Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e05\u003c\/td\u003e\n      \u003ctd\u003e0.5 meter (20 in)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eD: Connector and Cable-Type Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e02\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector, standard cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eE: Agency Approval Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e05\u003c\/td\u003e\n      \u003ctd\u003eMultiple Approvals (CSA, ATEX, IECEx)\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eParameter\u003c\/th\u003e\n      \u003cth\u003eValue\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eManufacturer\u003c\/td\u003e\n      \u003ctd\u003eBently Nevada (Baker Hughes)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eModel \/ Part Number\u003c\/td\u003e\n      \u003ctd\u003e330908-00-46-05-02-05\u003c\/td\u003e\n      \u003ctd\u003e3300 NSv Probe, 3\/8-24 UNF, without armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eProbe Tip Diameter\u003c\/td\u003e\n      \u003ctd\u003e5.26 mm (0.207 in) maximum\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eThread Type\u003c\/td\u003e\n      \u003ctd\u003e3\/8-24 UNF-2A\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eThreaded Length (Case)\u003c\/td\u003e\n      \u003ctd\u003e4.6 in\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eUnthreaded Length\u003c\/td\u003e\n      \u003ctd\u003e0.0 in (fully threaded)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eCable Type\u003c\/td\u003e\n      \u003ctd\u003e75-ohm coaxial, fluoroethylene propylene (FEP) insulated\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eIntegrated Cable Length\u003c\/td\u003e\n      \u003ctd\u003e0.5 meters (20 inches)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eConnector\u003c\/td\u003e\n      \u003ctd\u003eMiniature male coaxial ClickLoc connector\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eLinear Range\u003c\/td\u003e\n      \u003ctd\u003e1.5 mm (60 mils), from approximately 0.25 to 1.75 mm (10 to 70 mils)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eIncremental Scale Factor (ISF)\u003c\/td\u003e\n      \u003ctd\u003e7.87 V\/mm (200 mV\/mil)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eDeviation from Best Fit Straight Line (DSL)\u003c\/td\u003e\n      \u003ctd\u003eLess than +\/-0.06 mm (+\/-2.3 mils)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eRecommended Gap Setting\u003c\/td\u003e\n      \u003ctd\u003e1.0 mm (40 mils)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eProbe Tip Material\u003c\/td\u003e\n      \u003ctd\u003ePolyphenylene sulfide (PPS)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eProbe Case Material\u003c\/td\u003e\n      \u003ctd\u003eAISI 304 stainless steel (SST)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eOperating and Storage Temperature\u003c\/td\u003e\n      \u003ctd\u003e-52 degC to +177 degC (-62 degF to +351 degF)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003ePressure Rating\u003c\/td\u003e\n      \u003ctd\u003eSealed differential pressure with Viton O-ring between tip and case\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eTensile Strength\u003c\/td\u003e\n      \u003ctd\u003e220 N (50 lb) maximum rated probe case to probe lead\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eMinimum Cable Bend Radius\u003c\/td\u003e\n      \u003ctd\u003e25.4 mm (1.0 in)\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCable Routing:\u003c\/strong\u003e Avoid routing coaxial cables in areas where they are subject to physical pinching or sharp bends. Maintain a minimum bend radius of 25.4 mm (1.0 in).\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCase Mounting:\u003c\/strong\u003e Thread the probe into the mounting bracket or machine casing to the proper depth. For 3\/8-24 UNF threads, do not exceed the maximum rated torque of 33.9 N m (300 in-lb); a recommended torque of 11.3 N m (100 in-lb) is suggested.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCalibration Gap:\u003c\/strong\u003e Adjust the probe to a recommended gap of 1.0 mm (40 mils) from the target surface using a feeler gauge or by measuring the DC output voltage of the Proximitor sensor.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eConnector Protection:\u003c\/strong\u003e Ensure the ClickLoc connectors are kept clean and free of oil or moisture. Use silicone tape or connector protectors when installing in harsh environments.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eCompliance and Certifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eEMC:\u003c\/strong\u003e European Community Directive 2014\/30\/EU, standards EN 61000-6-2 and EN 61000-6-4.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eRoHS:\u003c\/strong\u003e European Community Directive 2011\/65\/EU and China RoHS (EFUP designation of 15 years).\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eHazardous Area Approvals (Option 05):\u003c\/strong\u003e ATEX\/IECEx (Class I, Zone 0: Ex ia IIC T5...T1 Ga; Ex ia IIIC T90degC...T280degC Dc; Class I, Zone 2: Ex nA IIC T5...T1 Gc; Ex ec IIC T5...T1 Gc) and North American certifications (Class I, Div 1, Groups A, B, C, D; Class I, Div 2, Groups A, B, C, D).\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eFunctional Safety:\u003c\/strong\u003e SIL 2 (HFT = 0), SIL 3 (HFT = 1).\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666526433643,"sku":"330908-00-46-05-02-05","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330908-00-46-05-02-05-3300-nsv-probe-tvwd5ijwn05_026b7e2e-1918-4ef6-8281-7dc43aca25ee.jpg?v=1765440286"},{"product_id":"bently-nevada-330701-00-25-10-11-05-3300-xl-11-mm-proximity-probe","title":"Bently Nevada 330701-00-25-10-11-05 3300 XL 11 mm Proximity Probe","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\n\u003cp\u003eOption 00 (0.0 in unthreaded length), Option 25 (2.5 in overall case length), Option 10 (1.0 m total length), Option 11 (ClickLoc connector with protector, FluidLoc cable), and Option 05 (Multiple approvals) specify the exact configuration of this \u003cstrong\u003e330701-00-25-10-11-05\u003c\/strong\u003e \u003cstrong\u003e3300 XL 11 mm Proximity Probe\u003c\/strong\u003e. This non-contacting eddy-current sensor operates within a 3300 XL 11 mm Proximity Transducer System to provide dynamic displacement and static position measurements on rotating machinery. The unarmored 1\/2-20 UNF threaded case configuration allows direct installation in tapped machine housings where external mechanical armor is unnecessary, while the integrated FluidLoc cable prevents moisture and process oil from migrating through the internal probe cable.\u003c\/p\u003e\n\u003cp\u003eUnlike configuration variants that feature standard coaxial cables (Option 01 or 02) or lack mechanical protection at the connection point, this probe utilizes Option 11 to provide both a FluidLoc barrier and a factory-installed connector protector, protecting the ClickLoc coaxial connection from contamination. Additionally, with Option 05, this probe is certified for multiple hazardous area environments (including ATEX, IECEx, and CSA), whereas standard Option 00 probes have no agency approvals. It features an 11 mm tip diameter that provides an extended 4.0 mm (160 mils) linear range, which is significantly longer than standard 8 mm systems, making it suitable for large axial thrust measurements, ramp differential expansion, and reciprocating compressor rod drop monitoring.\u003c\/p\u003e\n\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eOption 00 Unthreaded Case:\u003c\/strong\u003e Features a 0.0-inch unthreaded length, making the 2.5-inch case (Option 25) fully threaded with 1\/2-20 UNF threads for flexible mounting depth.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eOption 11 FluidLoc Cable:\u003c\/strong\u003e Incorporates an FEP-insulated FluidLoc triaxial cable that prevents oil and moisture leakage through the interior of the probe cable, combined with a pre-installed coaxial connector protector.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eOption 10 Total Length:\u003c\/strong\u003e Designed as a 1.0-meter (3.3 feet) integral probe system, typically paired with a 4.0-meter extension cable to complete a 5.0-meter system length.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eOption 05 Multiple Approvals:\u003c\/strong\u003e Fully certified under ATEX, IECEx, and CSA standards for safe operation in Class I Division 1\/2 and Zone 0\/2 hazardous locations.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e11 mm Tip Diameter:\u003c\/strong\u003e Provides an extended linear range of 4.0 mm (160 mils) and a nominal scale factor of 3.94 V\/mm (100 mV\/mil).\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eAxial thrust position measurements on steam and gas turbines\u003c\/li\u003e\n  \u003cli\u003eRamp differential expansion measurements on industrial turbomachinery\u003c\/li\u003e\n  \u003cli\u003eRod drop and rod position monitoring on reciprocating compressors\u003c\/li\u003e\n  \u003cli\u003eShaft vibration monitoring on large fluid-film bearing machines\u003c\/li\u003e\n  \u003cli\u003eTachometer, zero speed, and Keyphasor phase reference signal generation\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eOption Segment\u003c\/th\u003e\n      \u003cth\u003eCode on This SKU\u003c\/th\u003e\n      \u003cth\u003eDescription \/ Configuration Detail\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOrderable Part Number\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e\u003cstrong\u003e330701-00-25-10-11-05\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e3300 XL 11 mm Proximity Probe, 1\/2-20 UNF thread, without armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eA - Unthreaded Length Option\u003c\/td\u003e\n      \u003ctd\u003e00\u003c\/td\u003e\n      \u003ctd\u003e0.0 in (0 mm) unthreaded length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eB - Overall Case Length Option\u003c\/td\u003e\n      \u003ctd\u003e25\u003c\/td\u003e\n      \u003ctd\u003e2.5 in (64 mm) overall case length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eC - Total Length Option\u003c\/td\u003e\n      \u003ctd\u003e10\u003c\/td\u003e\n      \u003ctd\u003e1.0 meter (3.3 feet) total length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eD - Connector \u0026amp; Cable Option\u003c\/td\u003e\n      \u003ctd\u003e11\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector with connector protector, FluidLoc cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eE - Agency Approval Option\u003c\/td\u003e\n      \u003ctd\u003e05\u003c\/td\u003e\n      \u003ctd\u003eMultiple Approvals (CSA, ATEX, IECEx, etc.)\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eManufacturer\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eBently Nevada (Baker Hughes)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003ePart Number \/ SKU\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330701-00-25-10-11-05\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProduct Series\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e3300 XL 11 mm Proximity Transducer System\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eLinear Range\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e4.0 mm (160 mils), from approximately 0.5 to 4.5 mm (20 to 180 mils)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eNominal Scale Factor\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e3.94 V\/mm (100 mV\/mil) +\/-10%\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eDeviation from Straight Line (DSL)\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eLess than +\/-0.10 mm (+\/-4 mils) at standard temperatures; less than +\/-0.15 mm (+\/-6 mils) over extended temperatures\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eRecommended Target Size\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eAISI 4140 steel target, 30.5 mm (1.2 in) diameter or larger\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eRecommended Gap Setting\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e2.5 mm (100 mils)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOperating and Storage Temperature\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e-52 degC to +177 degC (-62 degF to +351 degF)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Tip Material\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003ePolyphenylene sulfide (PPS)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Case Material\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eAISI 304 stainless steel (SST)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eCable Specification\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e75 ohm triaxial, FEP-insulated FluidLoc cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eConnector Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector with pre-installed connector protector\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eConnector Material\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eGold-plated brass\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eTensile Strength (Maximum Rated)\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330 N (75 lb) probe case to probe lead; 270 N (60 lb) probe lead to extension cable connectors\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eMinimum Bend Radius\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e25.4 mm (1.0 in)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eMaximum Probe Case Torque\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e45.2 N-m (400 in-lb) rated; 15.2 N-m (133 in-lb) recommended\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe DC Resistance\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e5.9 +\/-0.5 ohms (between center conductor and outer conductor for 1.0 m length)\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eHand-tighten the probe case into the tapped hole and then tighten to the recommended installation torque of 15.2 N-m (133 in-lb). Do not exceed the maximum rated case torque of 45.2 N-m (400 in-lb).\u003c\/li\u003e\n  \u003cli\u003eMaintain a minimum cable bend radius of 25.4 mm (1.0 in) when routing the integral FluidLoc triaxial cable to avoid signal attenuation or conductor damage.\u003c\/li\u003e\n  \u003cli\u003eEnsure that the total probe length (1.0 m) and extension cable length (typically 4.0 m) match the 5.0-meter system length designated on the 3300 XL Proximitor Sensor.\u003c\/li\u003e\n  \u003cli\u003eEnsure the ClickLoc connection is fully protected with the pre-installed connector protector to prevent ingress of industrial oils, water, or other process contaminants.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eCompliance and Certifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eEMC:\u003c\/strong\u003e Complies with European Community Directive 2014\/30\/EU, EN 61000-6-2 (Industrial Immunity), and EN 61000-6-4 (Industrial Emissions).\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eRoHS:\u003c\/strong\u003e Complies with EU Directive 2011\/65\/EU and China RoHS regulations.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eHazardous Area Approvals (Option 05):\u003c\/strong\u003e\n    \u003cul\u003e\n      \u003cli\u003e\n\u003cstrong\u003eATEX\/IECEx:\u003c\/strong\u003e Ex ia IIC T5...T1 Ga; Ex ia IIIC T90degC...T280degC Dc; Ex nA IIC T5...T1 Gc; Ex ec IIC T5...T1 Gc.\u003c\/li\u003e\n      \u003cli\u003e\n\u003cstrong\u003eNorth America (CSA):\u003c\/strong\u003e Class I, Zone 0, AEx ia IIC T5...T1 Ga; Class I, Division 1, Groups A, B, C, and D; Class I, Division 2, Groups A, B, C, and D.\u003c\/li\u003e\n    \u003c\/ul\u003e\n  \u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666526499179,"sku":"330701-00-25-10-11-05","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330701-00-25-10-11-05-11-mm-proximity-probes-qhsolr2psmx_89d3c839-1ddd-4359-a597-2e3ae6843595.jpg?v=1765440287"},{"product_id":"bently-nevada-330103-00-05-05-01-05-3300-xl-8-mm-proximity-probe","title":"Bently Nevada 330103-00-05-05-01-05 3300 XL 8 mm Proximity Probe","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\n\u003cp\u003eOption 00 (0 mm unthreaded length), Option 05 (50 mm case length), and Option 05 (0.5 m total length) specify this \u003cstrong\u003e3300 XL 8 mm proximity probe\u003c\/strong\u003e configuration — \u003cstrong\u003e330103-00-05-05-01-05\u003c\/strong\u003e, which features an unarmored standard metric case and a coaxial ClickLoc connector with a pre-installed connector protector.\u003c\/p\u003e\n\u003cp\u003eIn contrast to variants with longer cable runs (such as 1.0 m or 2.0 m options) or armored protection sleeves, this 330103 configuration provides a compact 0.5-meter standard cable solution. The integrated connector protector guards the ClickLoc terminal from mechanical damage and moisture intrusion, making it suitable for confined spaces inside machine housings. With a fully threaded 50 mm case and zero unthreaded length, the probe offers maximum mounting adjustability within standard metric brackets.\u003c\/p\u003e\n\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eM10 x 1 thread body style without protective armor.\u003c\/li\u003e\n  \u003cli\u003e0 mm unthreaded length for direct flush-mounting applications.\u003c\/li\u003e\n  \u003cli\u003e50 mm overall case length provides mounting depth flexibility.\u003c\/li\u003e\n  \u003cli\u003e0.5 meter (1.6 feet) total length standard coaxial cable.\u003c\/li\u003e\n  \u003cli\u003eMiniature coaxial ClickLoc connector supplied with a pre-installed connector protector.\u003c\/li\u003e\n  \u003cli\u003eCertified for hazardous area installations under CSA, ATEX, and IECEx approvals.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cp\u003eIndustrial machinery vibration monitoring and axial position measurements in rotating equipment. Commonly used on steam turbines, gas turbines, centrifugal compressors, pumps, and generators to track shaft displacement, differential expansion, and keyphasor reference signals.\u003c\/p\u003e\n\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003ctable border=\"1\"\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eOption \/ Segment\u003c\/th\u003e\n      \u003cth\u003eCode on This SKU\u003c\/th\u003e\n      \u003cth\u003eDescription\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eOrderable Part Number\u003c\/td\u003e\n      \u003ctd\u003e330103-00-05-05-01-05\u003c\/td\u003e\n      \u003ctd\u003e3300 XL 8 mm proximity probe, M10 x 1 thread, without armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eA - Unthreaded Length Option\u003c\/td\u003e\n      \u003ctd\u003e00\u003c\/td\u003e\n      \u003ctd\u003e0 mm\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eB - Overall Case Length Option\u003c\/td\u003e\n      \u003ctd\u003e05\u003c\/td\u003e\n      \u003ctd\u003e50 mm\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eC - Total Length Option\u003c\/td\u003e\n      \u003ctd\u003e05\u003c\/td\u003e\n      \u003ctd\u003e0.5 meter (1.6 feet)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eD - Connector and Cable-Type Option\u003c\/td\u003e\n      \u003ctd\u003e01\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector with connector protector, standard cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eE - Agency Approval Option\u003c\/td\u003e\n      \u003ctd\u003e05\u003c\/td\u003e\n      \u003ctd\u003eCSA, ATEX, IECEx Approvals\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable border=\"1\"\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eParameter\u003c\/th\u003e\n      \u003cth\u003eValue\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eManufacturer\u003c\/td\u003e\n      \u003ctd\u003eBently Nevada\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003ePart Number\u003c\/td\u003e\n      \u003ctd\u003e330103-00-05-05-01-05\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eProduct Type\u003c\/td\u003e\n      \u003ctd\u003e3300 XL 8 mm Proximity Probe\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eThread Size\u003c\/td\u003e\n      \u003ctd\u003eM10 x 1\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eArmor Option\u003c\/td\u003e\n      \u003ctd\u003eNone\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eUnthreaded Length\u003c\/td\u003e\n      \u003ctd\u003e0 mm\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eCase Length\u003c\/td\u003e\n      \u003ctd\u003e50 mm\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eTotal Length\u003c\/td\u003e\n      \u003ctd\u003e0.5 meter (1.6 feet)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eConnector Type\u003c\/td\u003e\n      \u003ctd\u003eMiniature male coaxial ClickLoc\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eConnector Protector\u003c\/td\u003e\n      \u003ctd\u003eIncluded (Option 01)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eCable Type\u003c\/td\u003e\n      \u003ctd\u003eStandard 75 ohm coaxial cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eProbe Tip Diameter\u003c\/td\u003e\n      \u003ctd\u003e8.0 mm (0.31 inches)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eOperating Temperature (Probe)\u003c\/td\u003e\n      \u003ctd\u003e-52 degC to +177 degC (-62 degF to +350 degF)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eDifferential Pressure Seal\u003c\/td\u003e\n      \u003ctd\u003eSeals up to 7.0 bar (100 psi)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eMinimum Target Diameter\u003c\/td\u003e\n      \u003ctd\u003e15.2 mm (0.6 inches)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eLinear Range\u003c\/td\u003e\n      \u003ctd\u003e2.0 mm (80 mils) nominal\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eWeight\u003c\/td\u003e\n      \u003ctd\u003e0.16 kg\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eDimensions\u003c\/td\u003e\n      \u003ctd\u003e130 mm x 130 mm x 40 mm (H x W x D)\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eConnections and Interfaces\u003c\/h3\u003e\n\u003ctable border=\"1\"\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eInterface Component\u003c\/th\u003e\n      \u003cth\u003eSpecifications\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eConnector Type\u003c\/td\u003e\n      \u003ctd\u003eMiniature male coaxial ClickLoc with gold-plated contact pins\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eCoaxial Cable\u003c\/td\u003e\n      \u003ctd\u003e75 Ohm low-loss shielded cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\n\u003cp\u003eMount the probe in M10 x 1 threaded holes using a standard metric bracket. Verify that the thread engagement does not exceed the limit of 15 mm to prevent binding. Verify that the probe tip has clear space from surrounding metal (at least 1.5 times the probe tip diameter) to prevent side-loading or cross-talk. Install the connector protector properly to seal the coaxial junction from fluid ingress and contamination. Maintain a minimum bend radius of 25.4 mm (1.0 inch) for the probe coaxial cable.\u003c\/p\u003e\n\n\u003ch3\u003eCompliance and Certifications\u003c\/h3\u003e\n\u003cp\u003eCSA, ATEX, IECEx approvals for use in hazardous areas (Intrinsically Safe and Non-Incendive configurations).\u003c\/p\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666527056235,"sku":"330103-00-05-05-01-05","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330103-00-05-05-01-05-proximity-probes-4hjd0umhvtz_c64522d7-4377-486f-b15b-3701f41324a4.jpg?v=1765440293"},{"product_id":"bently-nevada-330104-05-14-50-01-05-3300-xl-armored-proximity-probe","title":"Bently Nevada 330104-05-14-50-01-05 3300 XL Armored Proximity Probe","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e330104-05-14-50-01-05\u003c\/strong\u003e: 3300 XL 8 mm \u003cstrong\u003eproximity probe\u003c\/strong\u003e with M10 x 1 metric thread, protective stainless steel armor, 50 mm unthreaded length, 140 mm overall case length, 5.0-meter total cable length, ClickLoc connector with connector protector, and CSA\/ATEX\/IECEx approvals.\u003c\/p\u003e\n\u003cp\u003eThis configuration incorporates standard flexible AISI 302 or 304 stainless steel armor with an outer FEP jacket to defend the 75-ohm triaxial cable against physical abrasion and mechanical stress in challenging industrial environments. Unlike unarmored models or short-lead variants, this 5.0-meter probe is designed specifically for operation in physical configurations matching 5.0-meter Proximitor sensors without requiring separate extension cables, reducing connection points in the measurement chain.\u003c\/p\u003e\n\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eM10 x 1 metric thread configuration with a 140 mm case length and 50 mm unthreaded portion.\u003c\/li\u003e\n  \u003cli\u003eIntegrated stainless steel protective armor shielding the 75-ohm triaxial cable from physical wear.\u003c\/li\u003e\n  \u003cli\u003e5.0-meter total system length designed specifically for direct connection to 5-meter Proximitor sensors.\u003c\/li\u003e\n  \u003cli\u003eGold-plated miniature coaxial ClickLoc connector with an integrated connector protector.\u003c\/li\u003e\n  \u003cli\u003eHazardous area approvals including CSA, ATEX, and IECEx for intrinsically safe installations.\u003c\/li\u003e\n  \u003cli\u003eMolded polyphenylene sulfide (PPS) probe tip offering chemical and environmental resistance.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eShaft vibration and axial position measurement on high-speed rotating machinery.\u003c\/li\u003e\n  \u003cli\u003eIndustrial machinery protection systems for steam turbines, gas turbines, compressors, and pumps.\u003c\/li\u003e\n  \u003cli\u003eHazardous area machinery monitoring in oil and gas refineries, petrochemical plants, and power generation facilities.\u003c\/li\u003e\n  \u003cli\u003eOver-speed detection and industrial turbine housing expansion monitoring.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003ctable border=\"1\"\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eOption \/ Segment\u003c\/th\u003e\n      \u003cth\u003eCode on This SKU\u003c\/th\u003e\n      \u003cth\u003eDescription\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eBase Model\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330104\u003c\/td\u003e\n      \u003ctd\u003e3300 XL 8 mm Proximity Probe, M10 x 1 thread, with armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eA: Unthreaded Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e05\u003c\/td\u003e\n      \u003ctd\u003e50 mm unthreaded length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eB: Overall Case Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e14\u003c\/td\u003e\n      \u003ctd\u003e140 mm overall case length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eC: Total Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e50\u003c\/td\u003e\n      \u003ctd\u003e5.0 meters (16.4 feet) overall length (for 5 m Proximitor)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eD: Connector and Cable-Type Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e01\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector with connector protector, standard cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eE: Agency Approval Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e05\u003c\/td\u003e\n      \u003ctd\u003eCSA, ATEX, IECEx Approvals (Intrinsically Safe \/ Non-Incendive)\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable border=\"1\"\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eParameter\u003c\/th\u003e\n      \u003cth\u003eSpecification Value\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eManufacturer\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eBently Nevada (Baker Hughes)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eModel Number\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330104-05-14-50-01-05\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eTransducer Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eEddy-current proximity probe\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Tip Diameter\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e8.0 mm (0.31 in)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eThread Specification\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eM10 x 1 metric thread\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eUnthreaded Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e50 mm\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOverall Case Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e140 mm\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eTotal Probe Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e5.0 meters (16.4 feet)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eCable Armor\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eFlexible AISI 302 or 304 SST with FEP outer jacket\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eConnector Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector with connector protector\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Tip Material\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003ePolyphenylene sulfide (PPS)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Case Material\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eAISI 303 or 304 stainless steel (SST)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOperating Temperature\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e-52 to +177 degC (-62 to +350 Fahrenheit)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Pressure Rating\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eDesigned to seal differential pressure up to 7.0 bar (100 psi) between tip and case\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eTensile Strength\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330 N (75 lbf) maximum probe case to probe lead\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eMinimum Cable Bend Radius\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e25.4 mm (1.0 in)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eNominal DC Resistance\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e8.73 +\/- 0.50 ohms (center conductor to outer conductor for 5.0 m length)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eDimensions\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e250 mm x 250 mm x 45 mm (H x W x D)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eWeight\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e0.42 kg\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eInstall per Bently Nevada drawing 141092 for intrinsically safe (ia) installations or drawing 140979 for non-incendive (nA\/ec) environments.\u003c\/li\u003e\n  \u003cli\u003eUse a maximum torque rating of 22.6 N-m (200 in-lb) when mounting the probe case into the bracket or housing (reduce to 7.5 N-m \/ 66 in-lb for the first three threads).\u003c\/li\u003e\n  \u003cli\u003eEnsure the minimum cable bend radius of 25.4 mm (1.0 in) is maintained during routing.\u003c\/li\u003e\n  \u003cli\u003eDo not exceed 15 mm of thread engagement when installing the M10 x 1 probe case.\u003c\/li\u003e\n  \u003cli\u003eSecure the miniature coaxial ClickLoc connector hand-tight; the integrated connector protector prevents mechanical disconnects and moisture ingress.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eCompliance and Certifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eCSA, ATEX, IECEx Approvals (Ex ia IIC T5...T1 Ga, Ex nA IIC T5...T1 Gc, Ex ec IIC T5...T1 Gc)\u003c\/li\u003e\n  \u003cli\u003eRoHS Compliant (2011\/65\/EU)\u003c\/li\u003e\n  \u003cli\u003eCE Compliant (EMC Directive 2014\/30\/EU)\u003c\/li\u003e\n  \u003cli\u003eFunctional Safety: SIL 2 (HFT = 0), SIL 3 (HFT = 1) certified when part of a complete 3300 XL system\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666527154539,"sku":"330104-05-14-50-01-05","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330104-05-14-50-01-05-probes-kf1kfsgarjd_ee4e31e6-f6fa-4e98-8450-a93543370ae6.jpg?v=1765440294"},{"product_id":"bently-nevada-330101-00-50-15-02-05-3300-xl-8-mm-proximity-probe","title":"Bently Nevada 330101-00-50-15-02-05 3300 XL 8 mm Proximity Probe","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eBently Nevada 330101-00-50-15-02-05\u003c\/strong\u003e is a high-precision, non-contact \u003cstrong\u003e8 mm proximity probe\u003c\/strong\u003e belonging to the industry-standard 3300 XL series. This specific configuration is distinguished by having a completely threaded case with 0.0 inches of unthreaded length (unthreaded option 00) and an overall case length of 5.0 inches (option 50). To ensure precise signal integrity without the added weight or bulk of stainless steel armor, this probe features a 1.5-meter (4.9 feet) standard cable (option 15) terminated with a miniature coaxial ClickLoc connector (option 02). Additionally, it is certified with CSA, ATEX, and IECEx agency approvals (option 05) for hazardous locations.\u003c\/p\u003e\n\u003cp\u003eThis eddy-current transducer is designed to measure static shaft position and dynamic vibration on critical rotating machinery. By pairing with a compatible 3300 XL Proximitor sensor and an extension cable, it forms a complete 3300 XL monitoring chain. The probe is engineered to withstand extreme temperatures and harsh industrial fluids, making it ideal for continuous machinery protection in demanding power generation, oil and gas, and petrochemical processes.\u003c\/p\u003e\n\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFully Threaded 5.0-Inch Case:\u003c\/strong\u003e Designed with zero unthreaded length (0.0 in) for versatile mounting depth adjustment inside threaded machine housings.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStandard Non-Armored Cable:\u003c\/strong\u003e Includes a lightweight, high-temperature standard cable with a 1.5-meter total length for streamlined cable routing.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eClickLoc Miniature Coaxial Connector:\u003c\/strong\u003e Features a gold-plated ClickLoc connector that resists vibration loosening while simplifying connections to the extension cable.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHazardous Area Certified:\u003c\/strong\u003e Comes pre-approved with CSA, ATEX, and IECEx ratings, ensuring safe operation in Zone 0, Zone 1, and Division 1 environments.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRugged Material Construction:\u003c\/strong\u003e Built with a polyphenylene sulfide (PPS) probe tip and a stainless steel body to seal against moisture and high differential pressures.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cp\u003eThe Bently Nevada 330101-00-50-15-02-05 proximity probe is ideal for a wide range of critical machinery monitoring tasks, including:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eRadial vibration measurements in steam and gas turbine bearings.\u003c\/li\u003e\n\u003cli\u003eThrust (axial) position monitoring for compressor and pump rotors.\u003c\/li\u003e\n\u003cli\u003eShaft eccentricity and speed measurements on major industrial rotating machines.\u003c\/li\u003e\n\u003cli\u003ePermanently mounted machinery protection systems compliant with API 670 standards.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003cp\u003eThis Bently Nevada probe is custom-ordered according to specific physical and electrical options. The table below decodes the options configured on this specific SKU:\u003c\/p\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eOption Code\u003c\/th\u003e\n\u003cth\u003eConfigured Value\u003c\/th\u003e\n\u003cth\u003eDescription\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eBase Model\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e330101\u003c\/td\u003e\n\u003ctd\u003e3300 XL 8 mm Proximity Probe, 3\/8-24 UNF thread, without armor\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eA - Unthreaded Length\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e00\u003c\/td\u003e\n\u003ctd\u003e0.0 inches (fully threaded body)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eB - Overall Case Length\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e50\u003c\/td\u003e\n\u003ctd\u003e5.0 inches overall case length\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eC - Total Length\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e15\u003c\/td\u003e\n\u003ctd\u003e1.5 meters (4.9 feet) total probe length\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eD - Connector\/Cable Option\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e02\u003c\/td\u003e\n\u003ctd\u003eMiniature coaxial ClickLoc connector, standard cable\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eE - Agency Approval\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e05\u003c\/td\u003e\n\u003ctd\u003eCSA, ATEX, IECEx hazardous area approvals\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eParameter\u003c\/th\u003e\n\u003cth\u003eSpecification Value\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eManufacturer\u003c\/td\u003e\n\u003ctd\u003eBently Nevada\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePart Number\u003c\/td\u003e\n\u003ctd\u003e330101-00-50-15-02-05\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eProbe Tip Diameter\u003c\/td\u003e\n\u003ctd\u003e8 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eThread Size\u003c\/td\u003e\n\u003ctd\u003e3\/8-24 UNF-2A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMeasurement Type\u003c\/td\u003e\n\u003ctd\u003eDisplacement (proximity)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Principle\u003c\/td\u003e\n\u003ctd\u003eEddy current\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eLinear Range\u003c\/td\u003e\n\u003ctd\u003e2 mm (80 mils), from approximately 0.25 to 2.3 mm (10 to 90 mils)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eIncremental Scale Factor (ISF)\u003c\/td\u003e\n\u003ctd\u003e7.87 V\/mm (200 mV\/mil) nominal\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eRecommended Gap Voltage\u003c\/td\u003e\n\u003ctd\u003e-9 Vdc (approximately 1.27 mm or 50 mils)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eNominal Probe DC Resistance (R_PROBE)\u003c\/td\u003e\n\u003ctd\u003e7.73 +\/- 0.50 Ohms (center conductor to outer conductor)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOutput Resistance\u003c\/td\u003e\n\u003ctd\u003e50 Ohms\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating and Storage Temperature (Standard Probe)\u003c\/td\u003e\n\u003ctd\u003e-52 degC to +177 degC (-62 degF to +350 degF)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePressure Sealing Limit\u003c\/td\u003e\n\u003ctd\u003eSealed with Viton O-ring between probe tip and case\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eRelative Humidity Resistance\u003c\/td\u003e\n\u003ctd\u003eLess than 3% change in Average Scale Factor (ASF) under 93% humidity\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eConnector Type\u003c\/td\u003e\n\u003ctd\u003eGold-plated miniature coaxial ClickLoc connector\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e45 mm x 95 mm x 95 mm (H x W x D)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e0.14 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\n\u003cp\u003eTo ensure optimal system performance and longevity of the Bently Nevada 330101 probe, adhere to the following engineering and installation instructions:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eThread Engagement:\u003c\/strong\u003e Maximum recommended thread engagement is 0.563 inches (14 mm) to prevent binding during installation.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGap Setting:\u003c\/strong\u003e Mount the probe with the appropriate physical gap (typically -9 Vdc or 1.27 mm \/ 50 mils) corresponding to the system calibration.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCable Routing:\u003c\/strong\u003e Ensure the probe cable is routed away from high-voltage wiring, and employ proper shielding and grounding techniques in accordance with standard industrial vibration monitoring practices.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEnvironmental Protection:\u003c\/strong\u003e Standard probes operating below -34 degC (-30 degF) may experience a degraded pressure seal. Proper insulation or casing protection is advised in sub-zero locations.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eCompliance and Certifications\u003c\/h3\u003e\n\u003cp\u003eThe 330101-00-50-15-02-05 configuration includes the following major agency approvals:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCSA:\u003c\/strong\u003e Class I, Div 1, Groups A, B, C, D; Class II, Div 1, Groups E, F, G; Class III\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eATEX\/IECEx:\u003c\/strong\u003e Ex ia IIC T5...T1 Ga; Ex ia IIIC T90 Celsius...T280 Celsius Dc\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCE Mark:\u003c\/strong\u003e Compliant with applicable European Union directives\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666527220075,"sku":"330101-00-50-15-02-05","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330101-00-50-15-02-05-proximity-probes-rzcvy3d10ha_fd737c6a-95f9-4ce2-a013-92f2f5eefa36.jpg?v=1765440295"},{"product_id":"bently-nevada-330901-00-09-05-02-00-3300-nsv-proximity-probes","title":"Bently Nevada 330901-00-09-05-02-00 3300 NSv Proximity Probes","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\n\u003cp\u003eOption 00 (0.0 in unthreaded length) and Option 09 (0.9 in case length) specify the configuration of this \u003cstrong\u003e3300 NSv proximity probe\u003c\/strong\u003e — \u003cstrong\u003e330901-00-09-05-02-00\u003c\/strong\u003e. This standard mount, non-armored probe features a 1\/4-28 UNF thread and is used in machinery with tight physical clearance and reduced target area constraints, such as small centrifugal air compressors, refrigeration compressors, and process gas compressors. With a short 0.9-inch fully threaded case and a 0.5-meter (20-inch) total probe length, this configuration allows for non-contact displacement measurement in highly restricted internal enclosures where standard-sized probes cannot be installed.\u003c\/p\u003e\n\u003cp\u003eThis variant uses a standard 75-ohm coaxial cable with a miniature ClickLoc coaxial connector (Option 02) without an integrated connector protector, facilitating compact cable routing. Because it is optioned with no agency approvals (Option E = 00), this probe is used for general-purpose, non-hazardous industrial installations. It is compatible with the Bently Nevada 330980 Proximitor Sensor and 330930 extension cables, providing a standard scale factor of 7.87 V\/mm (200 mV\/mil) over a 1.5 mm (60 mils) linear range when paired as a complete transducer system.\u003c\/p\u003e\n\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eOption 00 specifies a fully threaded probe case with 0.0 inches of unthreaded length for maximum mounting flexibility.\u003c\/li\u003e\n  \u003cli\u003eOption 09 provides a compact 0.9-inch overall case length suitable for tight internal installation envelopes.\u003c\/li\u003e\n  \u003cli\u003eOption 05 provides a 0.5-meter (20-inch) FEP-insulated coaxial cable, minimizing routing slack inside the machine housing.\u003c\/li\u003e\n  \u003cli\u003eOption 02 provides a miniature coaxial ClickLoc connector with a standard unarmored cable, enabling secure, click-to-lock connections.\u003c\/li\u003e\n  \u003cli\u003eOption 00 specifies that agency approvals are not required, serving cost-effective general-purpose installations.\u003c\/li\u003e\n  \u003cli\u003eStandard 1\/4-28 UNF thread without stainless steel armor for straightforward mounting in pre-tapped bores.\u003c\/li\u003e\n  \u003cli\u003ePolyphenylene sulfide (PPS) tip material with patented TipLoc molding ensures a robust bond between the probe tip and case.\u003c\/li\u003e\n  \u003cli\u003ePatented CableLoc design provides up to 220 N (50 lb) of cable pull strength.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eSmall-bore machinery and high-speed rotating equipment with tight spatial constraints.\u003c\/li\u003e\n  \u003cli\u003eCentrifugal air compressors and refrigeration compressors.\u003c\/li\u003e\n  \u003cli\u003eProcess gas compressors and fluid-filmed bearing machinery.\u003c\/li\u003e\n  \u003cli\u003eRadial vibration, radial position, and axial position monitoring on small shaft diameters.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003ctable border=\"1\" cellpadding=\"5\"\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eOption \/ Segment\u003c\/th\u003e\n      \u003cth\u003eCode on This SKU\u003c\/th\u003e\n      \u003cth\u003eDescription\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eBase Part Number\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330901\u003c\/td\u003e\n      \u003ctd\u003e3300 NSv Proximity Probe, 1\/4-28 UNF thread, standard mount without armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eA: Unthreaded Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e00\u003c\/td\u003e\n      \u003ctd\u003e0.0 inches (0 mm) unthreaded length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eB: Overall Case Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e09\u003c\/td\u003e\n      \u003ctd\u003e0.9 inches (23 mm) overall case length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eC: Total Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e05\u003c\/td\u003e\n      \u003ctd\u003e0.5 meters (20 inches) total length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eD: Connector and Cable-Type Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e02\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector, standard cable (no connector protector)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eE: Agency Approval Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e00\u003c\/td\u003e\n      \u003ctd\u003eNo approvals required \/ general-purpose use\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable border=\"1\" cellpadding=\"5\"\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eParameter\u003c\/th\u003e\n      \u003cth\u003eSpecification Value\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eManufacturer\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eBently Nevada (Baker Hughes)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eModel SKU\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330901-00-09-05-02-00\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eThread Specification\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e1\/4-28 UNF-2A\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eArmor Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eUnarmored (standard coaxial cable)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eUnthreaded Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e0.0 inches (0 mm)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eCase Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e0.9 inches (23 mm)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eTotal Probe Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e0.5 meters (20 inches)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eLinear Range\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e1.5 mm (60 mils), from approximately 0.25 to 1.75 mm (10 to 70 mils)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eAverage Scale Factor (ASF)\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e7.87 V\/mm (200 mV\/mil)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eDeviation from Best Fit Straight Line (DSL)\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eLess than +\/-0.06 mm (+\/-2.3 mils)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eFrequency Response\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e0 to 10 kHz: +0, -3 dB typical\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Tip Material\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003ePolyphenylene sulfide (PPS)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Case Material\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eAISI 304 stainless steel (SST)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eCable Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e75 ohm coaxial, fluoroethylene propylene (FEP) insulated\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe DC Resistance (RPROBE)\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e4.0 +\/-0.5 ohms (center conductor to outer conductor)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOperating and Storage Temperature\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e-52 degC to +177 degC (-62 degF to +351 degF)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003ePressure Sealing\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eViton O-ring differential seal (sustained below -34 degC \/ -30 degF can affect seal)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eTensile Strength (Maximum Rated)\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e220 N (50 lb) probe case to lead, 220 N (50 lb) lead to connectors\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eRecommended Case Torque\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e5.1 N m (45 in lb) nominal, 7.3 N m (65 in lb) maximum\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eConnector Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eMiniature male coaxial ClickLoc connector (gold-plated brass)\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eConnections and Interfaces\u003c\/h3\u003e\n\u003ctable border=\"1\" cellpadding=\"5\"\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eConnection \/ Interface\u003c\/th\u003e\n      \u003cth\u003eType \/ Pin Assignment\u003c\/th\u003e\n      \u003cth\u003eFunction\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Cable End\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eMiniature Male Coaxial ClickLoc\u003c\/td\u003e\n      \u003ctd\u003eConnects to the 3300 NSv Extension Cable (mating female connector)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eInternal Conductor\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eCenter Pin (Gold-plated brass)\u003c\/td\u003e\n      \u003ctd\u003eTransmits high-frequency RF signal and returns DC\/AC dynamic voltage\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eExternal Conductor\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eOuter Ring \/ Shield (Gold-plated brass)\u003c\/td\u003e\n      \u003ctd\u003eCommon ground and electrostatic shielding return path\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eGap Setting:\u003c\/strong\u003e Set the probe gap to the nominal target of 1.0 mm (40 mils) or approximately -9.0 Vdc to -10.0 Vdc output at the Proximitor Sensor for axial or radial measurements.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eThread Engagement:\u003c\/strong\u003e Do not exceed 0.375 inches of thread engagement on 1\/4-28 UNF probe cases to avoid potential binding.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCase Torque:\u003c\/strong\u003e Torque the probe case to 5.1 N m (45 in lb) nominal during installation. Do not exceed the maximum limit of 7.3 N m (65 in lb).\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCable Bend Radius:\u003c\/strong\u003e Maintain a minimum bend radius of 25.4 mm (1.0 inch) for the probe cable to prevent attenuation or damage to the internal FEP insulation.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eConnector Tightening:\u003c\/strong\u003e ClickLoc connectors should be joined finger-tight; do not exceed 0.56 Nm (5 in lb) of torque.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eMoisture Protection:\u003c\/strong\u003e In environments with high humidity or exposure to liquids, protect the ClickLoc connections using silicone tape or connector protectors.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eCompliance and Certifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eRoHS:\u003c\/strong\u003e Compliant with European Community Directive 2011\/65\/EU and China RoHS standards.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eElectromagnetic Compatibility (EMC):\u003c\/strong\u003e Compliant with EMC Directive 2014\/30\/EU, standards EN 61000-6-2 (Immunity) and EN 61000-6-4 (Emissions).\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eFunctional Safety:\u003c\/strong\u003e SIL 2 (HFT=0) and SIL 3 (HFT=1) capable when used as part of a safety instrumented system.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eAgency Approval Option E = 00:\u003c\/strong\u003e General Purpose (no hazardous area approvals required).\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666527678827,"sku":"330901-00-09-05-02-00","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330901-00-09-05-02-00-proximity-probes-zfdbmqoge43_88000aab-7e3a-4ef0-a25e-dcedfbff1d8e.jpg?v=1765440302"},{"product_id":"bently-nevada-330103-00-15-10-02-05-3300-xl-8-mm-proximity-probe","title":"Bently Nevada 330103-00-15-10-02-05 3300 XL 8 mm Proximity Probe","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e330103-00-15-10-02-05\u003c\/strong\u003e: 3300 XL 8 mm proximity probe with M10 x 1 metric thread, configured without armor, featuring 0 mm unthreaded length (Option 00), 150 mm overall case length (Option 15), 1.0 meter total length (Option 10), and a Miniature ClickLoc coaxial connector on standard cable without connector protection (Option 02). This configuration includes Option 05 for CSA, ATEX, and IECEx agency approvals.\u003c\/p\u003e\n\u003cp\u003eThis unarmored metric probe variant is used for non-contact eddy-current shaft displacement and vibration measurements within a 3300 XL monitoring system. Unlike variants equipped with stainless steel armor or FluidLoc cable options, this configuration employs standard coaxial cabling and a standard unarmored sleeve, and is designed to operate in systems requiring metric M10 x 1 mounting threads and 150 mm of thread depth.\u003c\/p\u003e\n\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eM10 x 1 metric thread profile with a case length of 150 mm\u003c\/li\u003e\n  \u003cli\u003e0 mm unthreaded length maximizing the threaded engagement portion\u003c\/li\u003e\n  \u003cli\u003e1.0 meter total system length for direct connection or use with standard extension cables\u003c\/li\u003e\n  \u003cli\u003eMiniature coaxial ClickLoc connector with gold-plated brass components\u003c\/li\u003e\n  \u003cli\u003eStandard coaxial cable configuration without external protective armor\u003c\/li\u003e\n  \u003cli\u003eAgency approval option 05 certifying suitability for CSA, ATEX, and IECEx hazardous area installations\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eShaft vibration and axial position measurement on fluid-film bearing machines\u003c\/li\u003e\n  \u003cli\u003eKeyphasor reference and speed measurements on industrial machinery\u003c\/li\u003e\n  \u003cli\u003eIndustrial rotating machinery protection in oil and gas, petrochemical, and power generation plants\u003c\/li\u003e\n  \u003cli\u003eMonitoring radial dynamic motion and axial shaft position\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003ctable border=\"1\" style=\"width:100%; border-collapse:collapse;\"\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eOption \/ Segment\u003c\/th\u003e\n      \u003cth\u003eCode on This SKU\u003c\/th\u003e\n      \u003cth\u003eDescription\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOrderable Part Number\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330103-00-15-10-02-05\u003c\/td\u003e\n      \u003ctd\u003e3300 XL 8 mm proximity probe, M10 x 1 thread, without armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eA - Unthreaded Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e00\u003c\/td\u003e\n      \u003ctd\u003e0 mm unthreaded length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eB - Overall Case Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e15\u003c\/td\u003e\n      \u003ctd\u003e150 mm case length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eC - Total Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e10\u003c\/td\u003e\n      \u003ctd\u003e1.0 meter (3.3 feet) total length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eD - Connector and Cable-Type Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e02\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector, standard cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eE - Agency Approval Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e05\u003c\/td\u003e\n      \u003ctd\u003eCSA, ATEX, IECEx Approvals\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable border=\"1\" style=\"width:100%; border-collapse:collapse;\"\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eManufacturer\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eBently Nevada (Baker Hughes)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003ePart Number\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330103-00-15-10-02-05\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProduct Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e3300 XL 8 mm Proximity Probe (Metric)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eThread Size\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eM10 x 1\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eArmor Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eWithout armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eUnthreaded Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e0 mm\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eCase Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e150 mm\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eTotal Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e1.0 meter (3.3 feet)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eConnector Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eMiniature male coaxial ClickLoc connector\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eCable Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eStandard coaxial cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Tip Material\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003ePolyphenylene sulfide (PPS)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Case Material\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eAISI 303 stainless steel\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOperating Temperature\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e-52 to +177 degC (-62 to +350 degF)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Pressure Rating\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eSealed up to 7.0 bar (100 psi)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOutput Sensitivity\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e7.87 V\/mm (200 mV\/mil) when paired with 3300 XL Proximitor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eLinear Range\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e2.0 mm (80 mils), starting at approximately 0.25 mm (10 mils) from probe tip\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eDimensions\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e150 mm x 17 mm x 17 mm (H x W x D)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eWeight\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e0.15 kg\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eConnections and Interfaces\u003c\/h3\u003e\n\u003cp\u003eThe probe cable is terminated with a miniature gold-plated male ClickLoc coaxial connector that connects directly to a standard 3300 XL extension cable or Proximitor sensor.\u003c\/p\u003e\n\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\n\u003cp\u003eEnsure the mounting thread is tapped to M10 x 1. The maximum thread engagement length is 15 mm to prevent binding. A class-matched thread should be used for all internal threads. Do not exceed the maximum recommended torque during installation. For hazardous area installations, maintain grounding and shielding continuity in accordance with the system installation drawings.\u003c\/p\u003e\n\n\u003ch3\u003eCompliance and Certifications\u003c\/h3\u003e\n\u003cp\u003eThis probe configuration complies with the following certifications under Option 05:\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eCSA (Class I, Division 1 and 2, Groups A, B, C, D)\u003c\/li\u003e\n  \u003cli\u003eATEX (Zone 0, 1, 2, Group IIC)\u003c\/li\u003e\n  \u003cli\u003eIECEx (Zone 0, 1, 2, Group IIC)\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666527809899,"sku":"330103-00-15-10-02-05","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330103-00-15-10-02-05-3300-xl-8-mm-probe-dcytptlhlmy_08d170d8-0aa4-4c47-9f72-bc3a4ee97ad8.jpg?v=1765440304"},{"product_id":"bently-nevada-330102-00-40-50-02-00-3300-xl-8-mm-armored-proximity-probe","title":"Bently Nevada 330102-00-40-50-02-00 3300 XL 8 mm Armored Proximity Probe","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\n\u003cp\u003eOption 00 (0.0 in unthreaded) and Option 02 (ClickLoc, no connector protector) specify this 3300 XL 8 mm probe configuration — \u003cstrong\u003e330102-00-40-50-02-00\u003c\/strong\u003e. This armored proximity probe features a 4.0-inch case length (Option 40) and a 5.0-meter total length (Option 50), designed without hazardous area approvals (Option 00).\u003c\/p\u003e\n\u003cp\u003eUnlike non-armored siblings (such as the 330101 series) or configurations with connector protectors (Option 01), the 330102 model utilizes flexible AISI 302\/304 stainless steel armor with an FEP outer jacket to protect the coaxial cable from physical abrasion and chemical exposure. Additionally, the 5.0-meter length variant is calibrated specifically for 5-meter Proximitor systems, bypassing the need for separate extension cables in short-run installations.\u003c\/p\u003e\n\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eStandard 3\/8-24 UNF threaded body made from durable AISI 303\/304 stainless steel.\u003c\/li\u003e\n  \u003cli\u003eOption 00 unthreaded length providing 0.0 in (0 mm) of unthreaded shaft, maximizing thread engagement in the mounting bracket.\u003c\/li\u003e\n  \u003cli\u003eOption 40 case length providing a 4.0 in (101.6 mm) overall threaded case for extended mounting reach.\u003c\/li\u003e\n  \u003cli\u003eOption 50 total length providing 5.0 m (16.4 ft) of system length, intended for direct integration with 5-meter Proximitor sensors.\u003c\/li\u003e\n  \u003cli\u003eOption 02 connector option providing a miniature gold-plated coaxial ClickLoc connector with standard 75-ohm FEP insulated triaxial cable.\u003c\/li\u003e\n  \u003cli\u003eOption 00 agency approval selection, suitable for non-hazardous locations or standard industrial applications.\u003c\/li\u003e\n  \u003cli\u003eIntegrated flexible AISI 302\/304 stainless steel armor with an FEP outer jacket to protect the cable in abrasive industrial environments.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cp\u003eThis transducer is primarily used for non-contact shaft vibration and axial position measurements in rotating machinery, including steam turbines, gas turbines, compressors, pumps, and generators. The integrated steel armor is ideal for applications where the routing path exposes the cable to mechanical wear, sharp edges, or environmental contaminants.\u003c\/p\u003e\n\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eOption \/ Segment\u003c\/th\u003e\n      \u003cth\u003eCode on This SKU\u003c\/th\u003e\n      \u003cth\u003eDescription\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOrderable Part Number\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330102-00-40-50-02-00\u003c\/td\u003e\n      \u003ctd\u003e3300 XL 8 mm proximity probe, 3\/8-24 UNF thread, with armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eA - Unthreaded Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e00\u003c\/td\u003e\n      \u003ctd\u003e0.0 in (0 mm)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eB - Overall Case Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e40\u003c\/td\u003e\n      \u003ctd\u003e4.0 in (101.6 mm)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eC - Total Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e50\u003c\/td\u003e\n      \u003ctd\u003e5.0 meters (16.4 feet)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eD - Connector and Cable Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e02\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector, standard cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eE - Agency Approval Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e00\u003c\/td\u003e\n      \u003ctd\u003eNot required\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eParameter\u003c\/th\u003e\n      \u003cth\u003eSpecification\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eManufacturer\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eBently Nevada (Baker Hughes)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003ePart Number\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330102-00-40-50-02-00\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Tip Material\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003ePolyphenylene sulfide (PPS)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eCase Material\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eAISI 303 or 304 stainless steel (SST)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eThread Size\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e3\/8-24 UNF-2A\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eUnthreaded Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e0.0 in (0 mm)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eCase Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e4.0 in (101.6 mm)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eTotal Probe Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e5.0 m (16.4 ft)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eArmor Material\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eFlexible AISI 302 or 304 SST with FEP outer jacket\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eCable Outside Diameter\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e3.68 mm (standard cable), 7.67 mm (with armor)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eConnector Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eMiniature gold-plated coaxial ClickLoc\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eSystem Compatability\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e5-meter 3300 XL Proximitor systems\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOperating Temperature (Probe)\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e-52 to +177 degC (-62 to +350 Fahrenheit)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Pressure Limit\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eDifferential pressure seal up to tip rating (Viton O-ring)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eNominal DC Resistance\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e8.73 ohms (typical for 5.0 m length)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eMinimum Cable Bend Radius\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e25.4 mm (1.0 in)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eTensile Strength (Max)\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330 N (75 lbf) probe case to lead\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eDimensions\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e250 mm x 250 mm x 45 mm (H x W x D) (typical coiled package)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eWeight\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e0.65 kg (650 g)\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\n\u003cp\u003eEnsure that the probe is properly gapped using a voltmeter or specialized gap calibration tool before finalizing the mechanical mounting. Maintain a minimum cable bend radius of 25.4 mm (1.0 in) to protect the internal FEP insulation. When tightening the probe case into the bracket, do not exceed the recommended torque limits. Always route the armored cable away from high-temperature exhaust paths and electrical power cables to mitigate thermal damage and electromagnetic interference.\u003c\/p\u003e\n\n\u003ch3\u003eCompliance and Certifications\u003c\/h3\u003e\n\u003cp\u003eThis series meets the following standards when part of a qualified 3300 XL Transducer system:\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eEMC: European Community Directive 2014\/30\/EU, standards EN 61000-6-2 and EN 61000-6-4.\u003c\/li\u003e\n  \u003cli\u003eRoHS: European Community Directive 2011\/65\/EU and China RoHS (15-year EFUP designation).\u003c\/li\u003e\n  \u003cli\u003eFunctional Safety: SIL 2 certified (HFT=0), SIL 3 capable (HFT=1) when configured as part of a safety instrumented system.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666528235883,"sku":"330102-00-40-50-02-00","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330102-00-40-50-02-00-proximity-probes-gotwhwpcq4x_681e7c20-17d7-42f3-beba-ea4aa683316f.jpg?v=1765440311"},{"product_id":"bently-nevada-330910-03-16-10-02-00-3300-nsv-proximity-probes","title":"Bently Nevada 330910-03-16-10-02-00 3300 NSv Proximity Probes","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\n\u003cp\u003eOption 03 (30 mm unthreaded length) and Option 16 (160 mm overall case length) specify this armored metric probe configuration - \u003cstrong\u003e330910-03-16-10-02-00\u003c\/strong\u003e, a \u003cstrong\u003e3300 NSv proximity probe\u003c\/strong\u003e with an M10x1 threaded body. This configuration features 30 mm of unthreaded length, a 160 mm overall case length, a 1.0-meter total cable length protected by stainless steel armor, a miniature coaxial ClickLoc connector without an integrated connector protector, and does not require hazardous area agency approvals. Unlike non-armored metric alternatives like the 330905, this model provides integrated flexible stainless steel armor to prevent cable abrasion and mechanical damage in deep-reach machine housings.\u003c\/p\u003e\n\n\u003cp\u003eUsed as part of the 3300 XL NSv transducer system, this probe provides non-contact displacement measurements in environments with reduced target areas or tight clearances, such as small-bore machinery, aeroderivative gas turbines, and high-speed shafts. It maintains a 1.5 mm (60 mils) linear range when paired with a compatible 330980 Proximitor sensor and a 330930 extension cable.\u003c\/p\u003e\n\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eOption 03 designates a 30 mm unthreaded length on a metric M10x1 threaded body.\u003c\/li\u003e\n  \u003cli\u003eOption 16 provides a 160 mm overall case length for deep-reach installation depth.\u003c\/li\u003e\n  \u003cli\u003eOption 10 supplies a 1.0-meter (39-inch) total probe length.\u003c\/li\u003e\n  \u003cli\u003eOption 02 includes a miniature coaxial ClickLoc connector with standard 75 ohm coaxial cable.\u003c\/li\u003e\n  \u003cli\u003eIntegrated stainless steel armor provides physical cable protection in high-friction machinery applications.\u003c\/li\u003e\n  \u003cli\u003eGold-plated brass ClickLoc connectors secure electrical connections and prevent accidental loosening under vibration.\u003c\/li\u003e\n  \u003cli\u003ePolyphenylene sulfide (PPS) probe tip offers chemical and fluid resistance inside process machine casings.\u003c\/li\u003e\n  \u003cli\u003eViton O-ring seals differential pressure between the probe tip and case.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eSmall-bore machinery vibration and position monitoring\u003c\/li\u003e\n  \u003cli\u003eAeroderivative gas turbine displacement measurements\u003c\/li\u003e\n  \u003cli\u003eHigh-speed rotating equipment with constrained target geometries\u003c\/li\u003e\n  \u003cli\u003eRadial vibration and axial position measurements on shafts smaller than 20 mm (0.8 inches)\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eOption\u003c\/th\u003e\n      \u003cth\u003eCode on This SKU\u003c\/th\u003e\n      \u003cth\u003eDescription\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOrderable Part Number\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e\u003cstrong\u003e330910-03-16-10-02-00\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e3300 NSv Proximity Probe, M10X1 thread, with armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eA - Unthreaded Length Option\u003c\/td\u003e\n      \u003ctd\u003e03\u003c\/td\u003e\n      \u003ctd\u003e30 mm unthreaded length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eB - Overall Case Length Option\u003c\/td\u003e\n      \u003ctd\u003e16\u003c\/td\u003e\n      \u003ctd\u003e160 mm overall case length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eC - Total Length Option\u003c\/td\u003e\n      \u003ctd\u003e10\u003c\/td\u003e\n      \u003ctd\u003e1.0 meter (39 in) probe length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eD - Connector and Cable-Type Option\u003c\/td\u003e\n      \u003ctd\u003e02\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector, standard cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eE - Agency Approval Option\u003c\/td\u003e\n      \u003ctd\u003e00\u003c\/td\u003e\n      \u003ctd\u003eAgency approvals not required\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eManufacturer\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eBently Nevada\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003ePart Number\/Model\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330910-03-16-10-02-00\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Thread Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eM10x1 metric thread (with armor)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eMechanical Protection\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eStainless steel armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Tip Material\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003ePolyphenylene sulfide (PPS)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Case Material\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eAISI 304 stainless steel (SST)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Cable Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e75 ohm coaxial cable, fluoroethylene propylene (FEP) insulated\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eConnector Material\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eGold-plated brass ClickLoc connectors\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eLinear Range\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e1.5 mm (60 mils), beginning at approximately 0.25 mm (10 mils) from target\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eRecommended Gap Setting\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e1.0 mm (40 mils)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eIncremental Scale Factor (ISF)\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e7.87 V\/mm (200 mV\/mil) +12.5% \/ -20% including interchangeability error\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eDeviation from Best Fit Straight Line (DSL)\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eLess than +\/-0.06 mm (+\/-2.3 mils)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eTensile Strength (Maximum Rated)\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e220 N (50 lb) probe case to probe lead, probe lead to extension cable, and probe case to armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eMinimum Bend Radius\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e25.4 mm (1.0 in)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOperating and Storage Temperature (Probe)\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e-52 to +177 degC\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eRelative Humidity Limit\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e100% condensing, non-submersible when connectors are protected\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Pressure Seal\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eViton O-ring pressure seal\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eConnections and Interfaces\u003c\/h3\u003e\n\u003cp\u003eThe probe connects to a 3300 NSv extension cable via a miniature coaxial ClickLoc connection. The coaxial interface is secured with a gold-plated brass lock mechanism to maintain electrical continuity and prevent detachment under vibration.\u003c\/p\u003e\n\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eAvoid exceeding the maximum thread engagement length of 15 mm for M10x1 probe cases to prevent binding.\u003c\/li\u003e\n  \u003cli\u003eEnsure the minimum bend radius of the armored cable is at least 25.4 mm (1.0 in) during routing.\u003c\/li\u003e\n  \u003cli\u003eDo not expose the probe pressure seal to temperatures below -34 degC for sustained periods.\u003c\/li\u003e\n  \u003cli\u003eUse connector protectors or silicone self-fusing tape on the connection between the probe and extension cable to prevent liquid entry.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eCompliance and Certifications\u003c\/h3\u003e\n\u003cp\u003eThis configuration has the Agency Approval Option designated as '00' (Not required). It is intended for general-purpose industrial applications that do not require specific hazardous area certifications.\u003c\/p\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666528334187,"sku":"330910-03-16-10-02-00","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330910-03-16-10-02-00-3300-nsv-probe-jpirluga0oh_12ffdcba-1e79-4750-a326-d56abda2e4c9.jpg?v=1765440312"},{"product_id":"bently-nevada-330704-00-50-10-01-05-3300-xl-11-mm-proximity-probe","title":"Bently Nevada 330704-00-50-10-01-05 3300 XL 11 mm Proximity Probe","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e330704-00-50-10-01-05\u003c\/strong\u003e: 3300 XL 11 mm proximity probe with metric M14 x 1.5 thread and stainless steel armor. Option 00 specifies a 0 mm unthreaded length, Option 50 defines a 50 mm overall case length, and Option 10 indicates a 1.0 meter (3.3 feet) total probe length. It features a miniature coaxial ClickLoc connector with a pre-installed connector protector on a standard 75 ohm FEP-insulated cable (Option 01), combined with multiple international hazardous area certifications (Option 05).\u003c\/p\u003e\n\u003cp\u003eThis eddy-current proximity probe belongs to the 3300 XL 11 mm Proximity Transducer System, which is used for non-contacting vibration and displacement measurements on fluid film bearing machines. The protective flexible AISI 302 stainless steel armor shields the cable from physical wear and harsh industrial environments, contrasting with non-armored variants like the 330703 probe. The probe connects to a 3300 XL 11 mm extension cable and a 3300 XL 11 mm Proximitor Sensor to form a complete 5-meter or 9-meter measurement system.\u003c\/p\u003e\n\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eOption 00 (0 mm unthreaded length) and Option 50 (50 mm overall case length) provide a standard metric M14 x 1.5 threaded profile.\u003c\/li\u003e\n\u003cli\u003eOption 10 specifies a 1.0 meter (3.3 feet) total probe length, designed to connect directly to compatible 3300 XL extension cables.\u003c\/li\u003e\n\u003cli\u003eOption 01 includes a miniature coaxial ClickLoc connector along with a fluorosilicone connector protector to guard the connection from environmental contaminants.\u003c\/li\u003e\n\u003cli\u003eOption 05 provides multiple approvals for hazardous environments, including CSA, ATEX, and IECEx intrinsic safety and non-incendive ratings.\u003c\/li\u003e\n\u003cli\u003eFlexible AISI 302 stainless steel armor with FEP outer jacket offers robust mechanical protection for the triaxial probe cable.\u003c\/li\u003e\n\u003cli\u003ePolyphenylene sulfide (PPS) tip material resists chemical erosion and high temperatures in rotating machinery casings.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cp\u003eTypical applications for this transducer system configuration include:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eAxial (thrust) position measurements on steam turbines and turbomachinery.\u003c\/li\u003e\n\u003cli\u003eShaft radial vibration measurements on fluid film bearing machines.\u003c\/li\u003e\n\u003cli\u003eRamp differential expansion measurements on steam turbines.\u003c\/li\u003e\n\u003cli\u003eRod position or rod drop measurements on industrial reciprocating compressors.\u003c\/li\u003e\n\u003cli\u003eTachometer, zero speed, and phase reference (Keyphasor) signal generation.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eOption \/ Segment\u003c\/th\u003e\n      \u003cth\u003eCode on This SKU\u003c\/th\u003e\n      \u003cth\u003eMeaning \/ Description\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOrderable Part Number\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e\u003cstrong\u003e330704-00-50-10-01-05\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e3300 XL 11 mm Proximity Probe, M14 x 1.5 thread, with armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eA - Unthreaded Length\u003c\/td\u003e\n      \u003ctd\u003e00\u003c\/td\u003e\n      \u003ctd\u003e0 mm unthreaded length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eB - Overall Case Length\u003c\/td\u003e\n      \u003ctd\u003e50\u003c\/td\u003e\n      \u003ctd\u003e50 mm overall case length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eC - Total Length\u003c\/td\u003e\n      \u003ctd\u003e10\u003c\/td\u003e\n      \u003ctd\u003e1.0 meter (3.3 feet) total probe length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eD - Connector and Cable-Type\u003c\/td\u003e\n      \u003ctd\u003e01\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector with connector protector, standard cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eE - Agency Approval\u003c\/td\u003e\n      \u003ctd\u003e05\u003c\/td\u003e\n      \u003ctd\u003eMultiple Approvals (CSA, ATEX, IECEx intrinsic safety and non-sparking\/non-incendive)\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eParameter\u003c\/th\u003e\n      \u003cth\u003eSpecification Value\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eManufacturer\u003c\/td\u003e\n      \u003ctd\u003eBently Nevada (Baker Hughes)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003ePart Number \/ Model\u003c\/td\u003e\n      \u003ctd\u003e330704-00-50-10-01-05\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eTransducer System\u003c\/td\u003e\n      \u003ctd\u003e3300 XL 11 mm Proximity Transducer System\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eThread Type\u003c\/td\u003e\n      \u003ctd\u003eM14 x 1.5 metric thread\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eArmor Option\u003c\/td\u003e\n      \u003ctd\u003eFlexible AISI 302 stainless steel armor with FEP outer jacket\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eLinear Range\u003c\/td\u003e\n      \u003ctd\u003e4.0 mm (160 mils), beginning at approximately 0.5 mm (20 mils) from target to 4.5 mm (180 mils)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eRecommended Gap Setting\u003c\/td\u003e\n      \u003ctd\u003e2.5 mm (100 mils)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eIncremental Scale Factor (ISF)\u003c\/td\u003e\n      \u003ctd\u003e3.94 V\/mm (100 mV\/mil) +\/-10% over the 4.0 mm linear range\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eDeviation from Best Fit Straight Line (DSL)\u003c\/td\u003e\n      \u003ctd\u003eLess than +\/-0.10 mm (+\/-4 mils) at standard temperature; Less than +\/-0.15 mm (+\/-6 mils) over probe temp range -35 degC to +120 degC\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eProbe Tip Material\u003c\/td\u003e\n      \u003ctd\u003ePolyphenylene sulfide (PPS)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eProbe Case Material\u003c\/td\u003e\n      \u003ctd\u003eAISI 304 stainless steel (SST)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eProbe Cable Specification\u003c\/td\u003e\n      \u003ctd\u003e75 ohm triaxial, fluoroethylene propylene (FEP) insulated\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eProbe dc Resistance (R_PROBE)\u003c\/td\u003e\n      \u003ctd\u003e5.9 +\/- 0.5 ohms (center conductor to outer conductor for 1.0 m probe)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eOperating and Storage Temperature\u003c\/td\u003e\n      \u003ctd\u003e-52 degC to +177 degC (-62 degF to +351 degF)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eRelative Humidity\u003c\/td\u003e\n      \u003ctd\u003e100% condensing, non-submersible when connectors are protected\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eTensile Strength (Maximum Rated)\u003c\/td\u003e\n      \u003ctd\u003e330 N (75 lb) probe case to probe lead; 270 N (60 lb) at probe lead to extension cable connectors\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eMinimum Bend Radius\u003c\/td\u003e\n      \u003ctd\u003e25.4 mm (1.0 in) with or without SST armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eMaximum Rated Torque\u003c\/td\u003e\n      \u003ctd\u003e63.3 N-m (560 in-lb); Recommended installation torque: 21.1 N-m (187 in-lb)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eConnector-to-Connector Torque\u003c\/td\u003e\n      \u003ctd\u003eRecommended finger tight; Maximum torque: 0.565 N-m (5 in-lb)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eConnector Type\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector (gold-plated brass)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eConnector Protector\u003c\/td\u003e\n      \u003ctd\u003ePre-installed fluorosilicone material\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\n\u003cp\u003eWhen installing the 3300 XL 11 mm proximity probe, adhere to the following industrial engineering practices:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eThread Torque:\u003c\/strong\u003e Do not exceed the maximum rated torque of 63.3 N-m (560 in-lb) for M14 x 1.5 probe cases. The recommended installation torque is 21.1 N-m (187 in-lb).\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBend Radius:\u003c\/strong\u003e Maintain a minimum bend radius of 25.4 mm (1.0 inch) for the FEP-insulated coaxial cable and the stainless steel armor to avoid internal damage to the conductor.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnector Handling:\u003c\/strong\u003e Connection between the probe and extension cable should be finger-tight. The maximum allowable torque for the ClickLoc coaxial connector is 0.565 N-m (5 in-lb).\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnector Protection:\u003c\/strong\u003e Ensure the fluorosilicone connector protector is fully installed over the coaxial connection to prevent moisture, dirt, and oil contamination. Do not use silicone tape inside the machinery casing or in areas exposed to turbine oil.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProbe Gap Setting:\u003c\/strong\u003e Set the initial physical gap between the probe tip and the target to 2.5 mm (100 mils), which corresponds to the midpoint of the 4.0 mm (160 mils) linear range.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eCompliance and Certifications\u003c\/h3\u003e\n\u003cp\u003eThis proximity probe is certified under the Option 05 Multiple Approvals package for use in hazardous areas. Verified certifications include:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eATEX\/IECEx:\u003c\/strong\u003e Ex ia IIC T5...T1 Ga for intrinsically safe installations in Zone 0; Ex nA IIC T5...T1 Gc and Ex ec IIC T5...T1 Gc for Zone 2 installations.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCNRTLUs:\u003c\/strong\u003e Class I, Zone 0, AEx\/Ex ia IIC T5...T1 Ga; Class I, Div 1, Groups A, B, C, D; Class II, Groups E, F, G; Class III. Class I, Zone 2, AEx\/Ex nA IIC T5...T1 Gc; Class I, Div 2, Groups A, B, C, D.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSIL Compatibility:\u003c\/strong\u003e SIL 2 certified (HFT = 0) or SIL 3 certified (HFT = 1) when implemented as part of a complete safety instrumented system (SIS) with compliant Bently Nevada monitors.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEnvironmental:\u003c\/strong\u003e RoHS compliant and tested to IEC 68-2-3 for damp heat resistance.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666528498027,"sku":"330704-00-50-10-01-05","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330704-00-50-10-01-05-11mm-sensor-vpsygjuumcc_3819ce21-d777-4282-8af0-ea8758c789f5.jpg?v=1765440315"},{"product_id":"bently-nevada-330103-02-17-05-02-05-3300-xl-8-mm-proximity-probe","title":"Bently Nevada 330103-02-17-05-02-05 3300 XL 8 mm Proximity Probe","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e330103-02-17-05-02-05\u003c\/strong\u003e specifies this 3300 XL 8 mm proximity probe configuration, featuring an M10 x 1 metric thread, 20 mm of unthreaded body length (Option 02), and an overall case length of 170 mm (Option 17). This unarmored probe is manufactured with a 0.5-meter total cable length (Option 05), a miniature coaxial ClickLoc connector on standard triaxial cable (Option 02), and carries CSA, ATEX, and IECEx agency approvals for hazardous areas (Option 05).\u003c\/p\u003e\n\u003cp\u003eThis proximity probe is used for non-contact shaft vibration and axial position measurements in critical industrial machinery. The M10 x 1 threaded body provides metric mounting compatibility, while the 170 mm overall case length provides the extended reach necessary for deep-recessed mounting locations. The system operates on the eddy-current principle, delivering output voltage directly proportional to the gap distance when paired with a matching 3300 XL Proximitor sensor and standard extension cable.\u003c\/p\u003e\n\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eM10 x 1 metric threaded body constructed from AISI 303 or 304 stainless steel without armor.\u003c\/li\u003e\n  \u003cli\u003eOption 02 unthreaded length of 20 mm prevents thread binding in standard recessed mounting brackets.\u003c\/li\u003e\n  \u003cli\u003eOption 17 overall case length of 170 mm allows extended physical reach into machine casings.\u003c\/li\u003e\n  \u003cli\u003eOption 05 total probe length of 0.5 meters (1.6 feet) connects directly to local junction boxes.\u003c\/li\u003e\n  \u003cli\u003eOption 02 miniature coaxial ClickLoc gold-plated connector provides low-resistance signal coupling.\u003c\/li\u003e\n  \u003cli\u003eOption 05 CSA, ATEX, and IECEx approvals allow deployment in certified hazardous locations.\u003c\/li\u003e\n  \u003cli\u003ePolyphenylene sulfide (PPS) probe tip material withstands chemical exposure and high temperatures.\u003c\/li\u003e\n  \u003cli\u003eTipLoc molding process creates a molecular bond between the probe tip and the stainless steel body.\u003c\/li\u003e\n  \u003cli\u003eCableLoc design provides up to 330 N (75 lbf) of pull strength between the cable and the probe housing.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eRadial shaft vibration monitoring on high-speed fluid-film bearing machines such as steam turbines and centrifugal compressors.\u003c\/li\u003e\n  \u003cli\u003eAxial thrust position and casing expansion tracking in rotating machinery protection systems.\u003c\/li\u003e\n  \u003cli\u003eKeyphasor reference signals and speed measurement applications.\u003c\/li\u003e\n  \u003cli\u003eMachinery diagnostics and predictive maintenance in chemical processing plants, refineries, and power generation facilities.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eOption \/ Segment\u003c\/th\u003e\n      \u003cth\u003eCode on This SKU\u003c\/th\u003e\n      \u003cth\u003eDescription\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOrderable Part Number\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330103-02-17-05-02-05\u003c\/td\u003e\n      \u003ctd\u003e3300 XL 8 mm proximity probe, M10 x 1 thread, without armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eA - Unthreaded Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e02\u003c\/td\u003e\n      \u003ctd\u003e20 mm unthreaded length (order in increments of 10 mm)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eB - Overall Case Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e17\u003c\/td\u003e\n      \u003ctd\u003e170 mm overall case length (order in increments of 10 mm)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eC - Total Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e05\u003c\/td\u003e\n      \u003ctd\u003e0.5 meter (1.6 feet) total probe length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eD - Connector and Cable Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e02\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector, standard unarmored cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eE - Agency Approval Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e05\u003c\/td\u003e\n      \u003ctd\u003eCSA, ATEX, and IECEx hazardous area approvals\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eManufacturer\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eBently Nevada (Baker Hughes)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003ePart Number\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330103-02-17-05-02-05\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eTransducer Family\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e3300 XL 8 mm Proximity Transducer System\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eThread Size\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eM10 x 1 (without armor)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Tip Material\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003ePolyphenylene sulfide (PPS)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Case Material\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eAISI 303 or 304 stainless steel\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eNominal DC Resistance (Rprobe)\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e7.45 plus\/minus 0.50 Ohms (from center conductor to outer conductor)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eCable Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e75 Ohm triaxial, fluorinated ethylene propylene (FEP) insulated\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eConnector Material\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eGold-plated brass or gold-plated beryllium copper\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eMinimum Cable Bend Radius\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e25.4 mm (1.0 in)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOperating Temperature Range\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e-52 degC to +177 degC (-62 degF to +350 degF)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eMaximum Case Torque\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e22.6 N-m (200 in-lbf) rated; 7.5 N-m (66 in-lbf) recommended\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eMaximum Rated Cable Tensile Strength\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330 N (75 lbf) probe case to lead; 270 N (60 lbf) at connectors\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Pressure Rating\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eViton O-ring pressure seal between tip and case\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eDimensions\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e25 mm x 150 mm x 150 mm (H x W x D)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eWeight\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e0.15 kg\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eLimit thread engagement length to a maximum of 15 mm to prevent binding or mechanical interference during installation.\u003c\/li\u003e\n  \u003cli\u003eEnsure that the minimum cable bend radius of 25.4 mm (1.0 in) is maintained at all times during routing to prevent cable shield damage.\u003c\/li\u003e\n  \u003cli\u003eTighten the probe case to the recommended torque of 7.5 N-m (66 in-lbf). Do not exceed the maximum limit of 22.6 N-m (200 in-lbf).\u003c\/li\u003e\n  \u003cli\u003eConnectors must be finger-tight only. Do not exceed the maximum connector torque rating of 0.565 N-m (5 in-lbf).\u003c\/li\u003e\n  \u003cli\u003eMaintain a physical distance or utilize isolation brackets if electrical isolation is required between the probe body and machine housing.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eCompliance and Certifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCSA:\u003c\/strong\u003e Approved for hazardous areas when used with certified intrinsic barriers or non-incendive circuits.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eATEX\/IECEx:\u003c\/strong\u003e Certified for use in Zone 0, Zone 1, and Zone 2 explosive atmospheres with appropriate barrier devices.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCE:\u003c\/strong\u003e Fully compliant with applicable European Union directives for electromagnetic compatibility.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666528792939,"sku":"330103-02-17-05-02-05","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330103-02-17-05-02-05-proximity-probes-1mrxwyihxj5_6454c233-f967-42bf-a2ad-7d7b5577a541.jpg?v=1765440316"},{"product_id":"bently-nevada-330101-48-71-20-02-00-3300-xl-8-mm-proximity-probe","title":"Bently Nevada 330101-48-71-20-02-00 3300 XL 8 mm Proximity Probe","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eBently Nevada 330101-48-71-20-02-00\u003c\/strong\u003e is an 8 mm proximity probe belonging to the industry-standard \u003cstrong\u003e3300 XL 8 mm Proximity Transducer System\u003c\/strong\u003e. Designed for non-contact vibration and shaft position measurements, this probe operates on the eddy current principle to provide precise displacement feedback. This specific configuration features a 3\/8-24 UNF threaded body without armor, with a 4.8-inch unthreaded length, a 7.1-inch overall case length, and a total cable length of 2.0 meters (6.6 feet) terminated in a miniature coaxial ClickLoc connector with standard cable. It does not require agency approvals, making it an ideal choice for standard industrial environments where certified hazardous area protection is not mandatory.\u003c\/p\u003e\n\u003cp\u003eAs part of the 3300 XL series, this proximity probe offers excellent mechanical and environmental durability. It is fully compatible with 330180 series Proximitor sensors and standard 3300 XL extension cables. When integrated into a complete 3300 XL monitoring chain, it delivers highly accurate and repeatable measurements, ensuring reliable machinery protection for critical assets such as steam and gas turbines, compressors, pumps, and other rotating machinery.\u003c\/p\u003e\n\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eEddy-current technology for reliable non-contact displacement and vibration measurement.\u003c\/li\u003e\n  \u003cli\u003eSpecially configured with a 4.8-inch unthreaded portion and a 7.1-inch total case length.\u003c\/li\u003e\n  \u003cli\u003e2.0 meters (6.6 feet) of standard triaxial FEP-insulated probe cable for reliable signal transmission.\u003c\/li\u003e\n  \u003cli\u003eMiniature coaxial ClickLoc connector provides a secure, vibration-resistant connection.\u003c\/li\u003e\n  \u003cli\u003eViton O-ring pressure seal built into the probe tip to prevent leakages through the casing.\u003c\/li\u003e\n  \u003cli\u003eFully compatible with Bently Nevada 3300 XL series Proximitor sensors and extension cables.\u003c\/li\u003e\n  \u003cli\u003eDesigned for permanent mounting on bearing housings, machine casings, or external brackets.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cp\u003eThis proximity probe configuration is commonly deployed in various rotating machinery applications to monitor critical mechanical parameters:\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eShaft radial vibration measurements on high-speed turbines and compressors.\u003c\/li\u003e\n  \u003cli\u003eAxial thrust position and rotor displacement monitoring in pumps and gearboxes.\u003c\/li\u003e\n  \u003cli\u003eEccentricity and phase reference (Keyphasor) tracking.\u003c\/li\u003e\n  \u003cli\u003ePermanent machine protection in heavy-industry sectors including power generation, oil and gas, and chemical processing plants where standard, non-certified components are sufficient.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eOption \/ Segment\u003c\/th\u003e\n      \u003cth\u003eCode on This SKU\u003c\/th\u003e\n      \u003cth\u003eDescription \/ Meaning\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOrderable Part Number\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330101-48-71-20-02-00\u003c\/td\u003e\n      \u003ctd\u003e3300 XL 8 mm Proximity Probe, 3\/8-24 UNF thread, without armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eA - Unthreaded Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e48\u003c\/td\u003e\n      \u003ctd\u003e4.8 inches (122 mm) unthreaded length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eB - Overall Case Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e71\u003c\/td\u003e\n      \u003ctd\u003e7.1 inches (180 mm) overall case length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eC - Total Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e20\u003c\/td\u003e\n      \u003ctd\u003e2.0 meters (6.6 feet) total length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eD - Connector and Cable-Type Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e02\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector, standard cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eE - Agency Approval Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e00\u003c\/td\u003e\n      \u003ctd\u003eNo agency approvals required\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eParameter\u003c\/th\u003e\n      \u003cth\u003eSpecification Value\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eManufacturer\u003c\/td\u003e\n      \u003ctd\u003eBently Nevada\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eModel Number\u003c\/td\u003e\n      \u003ctd\u003e330101-48-71-20-02-00\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eProduct Family\u003c\/td\u003e\n      \u003ctd\u003e3300 XL 8 mm Proximity Transducer System\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eMeasurement Type\u003c\/td\u003e\n      \u003ctd\u003eDisplacement (proximity)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eOperating Principle\u003c\/td\u003e\n      \u003ctd\u003eEddy current\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eProbe Tip Diameter\u003c\/td\u003e\n      \u003ctd\u003e8 mm\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eThread Type\u003c\/td\u003e\n      \u003ctd\u003e3\/8-24 UNF-2A thread, without armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eLinear Range\u003c\/td\u003e\n      \u003ctd\u003e2 mm (80 mils), starting from approximately 0.25 mm (10 mils) up to 2.3 mm (90 mils)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eIncremental Scale Factor (ISF)\u003c\/td\u003e\n      \u003ctd\u003e7.87 V\/mm (200 mV\/mil) nominal\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eProbe Tip Material\u003c\/td\u003e\n      \u003ctd\u003ePolyphenylene sulfide (PPS)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eProbe Case Material\u003c\/td\u003e\n      \u003ctd\u003eAISI 303 or 304 stainless steel (SST)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eCable Type\u003c\/td\u003e\n      \u003ctd\u003e75 Ohm triaxial fluoroethylene propylene (FEP) insulated cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eTensile Strength\u003c\/td\u003e\n      \u003ctd\u003e330 N (75 lbf) maximum rated (probe case to probe lead)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eConnector Material\u003c\/td\u003e\n      \u003ctd\u003eGold-plated brass\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eRecommended Torque\u003c\/td\u003e\n      \u003ctd\u003e7.5 Nm (66 in-lbf) for case mounting; finger tight for coaxial connectors\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eProbe Temperature Range\u003c\/td\u003e\n      \u003ctd\u003e-52 degC to +177 degC (-62 degF to +350 degF) for operating and storage\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eMinimum Bend Radius\u003c\/td\u003e\n      \u003ctd\u003e25.4 mm (1.0 in) for standard probe cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eDimensions\u003c\/td\u003e\n      \u003ctd\u003e45 mm x 95 mm x 95 mm (H x W x D)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eWeight\u003c\/td\u003e\n      \u003ctd\u003e0.14 kg\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\n\u003cp\u003eTo achieve reliable vibration and position monitoring, follow these essential engineering and installation guidelines:\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProbe Gap:\u003c\/strong\u003e Ensure the probe is mounted with the appropriate gap setting matching the system calibration (typically gapped at 1.27 mm or -9 Vdc for radial vibration measurements over the linear range).\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eUnthreaded Length Selection:\u003c\/strong\u003e The 4.8-inch unthreaded length of this probe must be chosen correctly to clear mounting bosses or brackets without interfering with internal rotating components.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCable Protection \u0026amp; Bend Radius:\u003c\/strong\u003e Maintain a minimum cable bend radius of 25.4 mm (1.0 in). Route cables through conduits or protective trays to prevent mechanical damage, keeping them away from high-voltage lines to minimize electromagnetic interference.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCoaxial Connection:\u003c\/strong\u003e Ensure ClickLoc coaxial connectors are joined finger-tight. Avoid using heavy pliers or exceeding the maximum connector torque of 0.565 Nm (5 in-lbf).\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eGrounding \u0026amp; Shielding:\u003c\/strong\u003e Properly ground and shield the entire transducer loop. Shielding should typically be terminated at the monitor end, maintaining isolation at the probe casing.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eCompliance and Certifications\u003c\/h3\u003e\n\u003cp\u003eThis standard Bently Nevada 330101-48-71-20-02-00 configuration utilizes the -00 approval option and is designed for general purpose, non-hazardous industrial environments. It does not carry explosive atmosphere certifications (such as ATEX, IECEx, or CSA hazardous area approvals), which are designated under option code -05. However, it is manufactured under rigorous ISO 9001 quality management procedures and conforms to Bently Nevada's high mechanical, electrical, and environmental performance standards.\u003c\/p\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666528924011,"sku":"330101-48-71-20-02-00","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330101-48-71-20-02-00-probes-xz2tt3bkr0p_93808766-5d5f-4ca9-9b36-0e5ef11be6fa.jpg?v=1765440319"},{"product_id":"bently-nevada-330910-00-05-02-00-3300-nsv-proximity-probe","title":"Bently Nevada 330910-00-05-02-00 3300 NSv Proximity Probe","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\n\u003cp\u003eOption 00 (0 mm unthreaded length) and Option 05 (50 mm overall case length) specify this 3300 NSv armored metric probe configuration — \u003cstrong\u003e330910-00-05-02-00\u003c\/strong\u003e, a rugged \u003cstrong\u003e3300 NSv proximity probe\u003c\/strong\u003e designed with integrated stainless steel armor. It is used in tight installations and reduced target area scenarios where conventional 5 mm or 8 mm proximity systems cannot be deployed due to sideview or counterbore limitations. The probe features integrated M10x1 metric threads and robust stainless steel armor to protect the coaxial cable from physical abrasion, crushing, and harsh mechanical environments.\u003c\/p\u003e\n\n\u003cp\u003eThis variant is specifically configured for applications requiring a fully threaded casing of 50 mm without any unthreaded portion at the tip. It utilizes standard coaxial cable terminated with a miniature coaxial ClickLoc connector and is intended for non-hazardous locations where agency approvals are not required. It pairs with the 3300 XL NSv Proximitor Sensor (330980) and 3300 NSv Extension Cable (330930) to form a complete non-contact eddy-current measurement system.\u003c\/p\u003e\n\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eM10x1 metric threaded probe body with integrated stainless steel armor for high mechanical protection.\u003c\/li\u003e\n  \u003cli\u003eOption 00 unthreaded length specifies a fully threaded 0 mm profile.\u003c\/li\u003e\n  \u003cli\u003eOption 05 overall case length provides a compact 50 mm threaded housing.\u003c\/li\u003e\n  \u003cli\u003eMiniature coaxial ClickLoc connector secures connection and resists loosening under vibration.\u003c\/li\u003e\n  \u003cli\u003eStandard coaxial cable construction with gold-plated brass connector contacts.\u003c\/li\u003e\n  \u003cli\u003ePatented TipLoc molding delivers a secure bond between the polyphenylene sulfide (PPS) probe tip and the steel body.\u003c\/li\u003e\n  \u003cli\u003ePatented CableLoc design provides up to 220 N pull strength at the cable-to-probe junction.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eCentrifugal air compressors and industrial refrigeration compressors.\u003c\/li\u003e\n  \u003cli\u003eProcess gas compressors and high-speed turbomachinery with limited installation clearances.\u003c\/li\u003e\n  \u003cli\u003eSmall-bore machines with shaft diameters smaller than 51 mm.\u003c\/li\u003e\n  \u003cli\u003eAxial thrust and radial vibration monitoring on flat targets smaller than 15 mm.\u003c\/li\u003e\n  \u003cli\u003eTachometer, zero speed, and Keyphasor phase reference measurements.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eOption \/ Segment\u003c\/th\u003e\n      \u003cth\u003eCode Value\u003c\/th\u003e\n      \u003cth\u003eDescription \/ Meaning\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eBase Part Number\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330910\u003c\/td\u003e\n      \u003ctd\u003e3300 NSv Proximity Probe, Metric M10x1 thread, with stainless steel armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eSegment A: Unthreaded Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e00\u003c\/td\u003e\n      \u003ctd\u003e0 mm unthreaded length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eSegment B: Overall Case Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e05\u003c\/td\u003e\n      \u003ctd\u003e50 mm overall case length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eSegment C: Connector \/ Cable Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e02\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector, standard coaxial cable (no connector protector)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eSegment D: Agency Approval\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e00\u003c\/td\u003e\n      \u003ctd\u003eApprovals not required \/ standard commercial configuration\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eParameter\u003c\/th\u003e\n      \u003cth\u003eSpecification Value\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eManufacturer\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eBently Nevada (Baker Hughes)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eModel SKU\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330910-00-05-02-00\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eSystem Compatibility\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e3300 XL NSv Transducer System\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eThread Size\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eMetric M10x1\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eMechanical Protection\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eIntegrated stainless steel armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eLinear Range\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e1.5 mm (60 mils), beginning at 0.25 mm (10 mils) from the target\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eRecommended Gap Setting\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e1.0 mm (40 mils)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eIncremental Scale Factor (ISF)\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e7.87 V\/mm (200 mV\/mil)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eDeviation from Best Fit Straight Line (DSL)\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eLess than +\/-0.06 mm (+\/-2.3 mils) over linear range\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eFrequency Response\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e0 to 10 kHz (+0, -3 dB)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003ePower Requirements\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e-17.5 Vdc to -26 Vdc at 12 mA maximum consumption\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOutput Resistance\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e50 ohm\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eCable Resistance\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eCenter conductor: 0.220 ohm\/m; Shield: 0.066 ohm\/m\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eCable Capacitance\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e69.9 pF\/m typical\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOperating and Storage Temperature Range\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e-52 degC to +177 degC (-62 degF to +351 degF)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eRelative Humidity Limit\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e100% condensing, non-submersible (when connectors are protected)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eMaximum Recommended Thread Torque\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e11.3 N m (100 in lb)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eMaximum Rated Thread Torque\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e33.9 N m (300 in lb)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eMinimum Bend Radius\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e25.4 mm (1.0 in)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Case-to-Lead Pull Strength\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e220 N (50 lb)\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\n\u003cp\u003eTo avoid potential damage during installation, do not exceed the recommended installation torque of 11.3 N m (100 in lb) for this metric M10x1 threaded probe body. The minimum bend radius of 25.4 mm (1.0 in) must be observed for both armored and unarmored cable runs. Connectors must remain dry and free of contaminants; it is recommended to apply silicone self-fusing tape or a connector protector kit to the probe-to-extension cable junction to block moisture and process fluids. The field wiring should use a three-conductor shielded triad cable with a maximum length of 305 meters (1,000 feet) between the Proximitor Sensor and the monitoring system.\u003c\/p\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666528989547,"sku":"330910-00-05-02-00","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330910-00-05-02-00-3300-nsv-extension-cable-34c034e3o32_19f50961-ab46-4162-9d94-10dd4ce9b452.jpg?v=1765440320"},{"product_id":"bently-nevada-330101-02-21-10-01-00-3300-xl-8-mm-proximity-probe","title":"Bently Nevada 330101-02-21-10-01-00 3300 XL 8 mm Proximity Probe","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\nThe \u003cstrong\u003eBently Nevada 330101-02-21-10-01-00\u003c\/strong\u003e is an unarmored \u003cstrong\u003e8 mm proximity probe\u003c\/strong\u003e engineered for high-precision, non-contact machinery protection and condition monitoring. This specific configuration features a 3\/8-24 UNF thread with a short unthreaded case length of 0.2 inches (option 02) and an overall case length of 2.1 inches (option 21). Fitted with a 1.0 meter standard coaxial cable (option 10) and a miniature coaxial ClickLoc connector with an integrated connector protector (option 01), this sensor does not require agency approvals (option 00) and is optimized for standard industrial vibration chains.\n\nOperating on the eddy-current measurement principle, this probe determines the precise dynamic and static distance between the probe tip and a target conductive shaft. It is part of the 3300 XL 8 mm Transducer System, pairing with a 3300 XL extension cable and a 330180 series Proximitor sensor. Together, this chain generates a highly stable voltage output proportional to shaft vibration and position, feeding critical real-time diagnostic data to Bently Nevada 3500 rack modules or other machinery protection systems.\n\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eProximity tip diameter of 8 mm designed for precise non-contact eddy-current displacement measurements.\u003c\/li\u003e\n  \u003cli\u003eIntegrated connector protector (option 01) safeguarding the miniature ClickLoc coaxial connection against oil, moisture, and contaminants.\u003c\/li\u003e\n  \u003cli\u003eUnarmored stainless steel threaded body (3\/8-24 UNF) designed for bearing housing or machine casing mount.\u003c\/li\u003e\n  \u003cli\u003eCompact 0.2 in unthreaded length and 2.1 in case length for tight mechanical clearance installations.\u003c\/li\u003e\n  \u003cli\u003e1.0 meter total cable length (standard coaxial) suited for neat connection to local junction boxes.\u003c\/li\u003e\n  \u003cli\u003eExcellent thermal performance and mechanical durability across harsh industrial rotating environments.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eApplications\u003c\/h3\u003e\nThe \u003cstrong\u003eBently Nevada 330101-02-21-10-01-00\u003c\/strong\u003e probe is ideal for permanent mounting on critical rotating machinery, including:\n\u003cul\u003e\n  \u003cli\u003eSteam and gas turbine shaft vibration and axial position measurement.\u003c\/li\u003e\n  \u003cli\u003eRotor dynamic displacement monitoring in large compressors and industrial pumps.\u003c\/li\u003e\n  \u003cli\u003eBearing oil film clearance and thickness monitoring.\u003c\/li\u003e\n  \u003cli\u003eRadial vibration, thrust position, and speed sensing on high-speed rotating shafts.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eOption \/ Segment\u003c\/th\u003e\n      \u003cth\u003eCode on This SKU\u003c\/th\u003e\n      \u003cth\u003eDescription \/ Meaning\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eBase Model\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330101\u003c\/td\u003e\n      \u003ctd\u003e3300 XL 8 mm Probe, 3\/8-24 UNF thread, without armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eA - Unthreaded Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e02\u003c\/td\u003e\n      \u003ctd\u003e0.2 inches (5 mm) unthreaded length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eB - Overall Case Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e21\u003c\/td\u003e\n      \u003ctd\u003e2.1 inches (53 mm) overall case length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eC - Total Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e10\u003c\/td\u003e\n      \u003ctd\u003e1.0 meter (3.3 feet) total length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eD - Connector and Cable-Type Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e01\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector with connector protector, standard cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eE - Agency Approval Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e00\u003c\/td\u003e\n      \u003ctd\u003eNot required (No approvals)\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eParameter\u003c\/th\u003e\n      \u003cth\u003eSpecification Value\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eManufacturer\u003c\/td\u003e\n      \u003ctd\u003eBently Nevada\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003ePart Number \/ Model\u003c\/td\u003e\n      \u003ctd\u003e330101-02-21-10-01-00\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eProbe Diameter\u003c\/td\u003e\n      \u003ctd\u003e8 mm\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eMeasurement Type\u003c\/td\u003e\n      \u003ctd\u003eDisplacement (proximity)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eOperating Principle\u003c\/td\u003e\n      \u003ctd\u003eEddy current\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eThread Type\u003c\/td\u003e\n      \u003ctd\u003e3\/8-24 UNF\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eUnthreaded Length\u003c\/td\u003e\n      \u003ctd\u003e0.2 inches (5 mm)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eOverall Case Length\u003c\/td\u003e\n      \u003ctd\u003e2.1 inches (53 mm)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eTotal Length\u003c\/td\u003e\n      \u003ctd\u003e1.0 meter (3.3 feet)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eCable Type\u003c\/td\u003e\n      \u003ctd\u003eStandard coaxial cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eConnector Type\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc with connector protector\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eMechanical Protection\u003c\/td\u003e\n      \u003ctd\u003eWithout armor (unarmored)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eAgency Approvals\u003c\/td\u003e\n      \u003ctd\u003eNo approvals required (Option 00)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eOperating Temperature Range\u003c\/td\u003e\n      \u003ctd\u003e-51 degC to +177 degC (-60 degF to +350 degF)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eDimensions\u003c\/td\u003e\n      \u003ctd\u003e45 mm x 95 mm x 95 mm (H x W x D)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eWeight\u003c\/td\u003e\n      \u003ctd\u003e0.14 kg\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\nEnsure reliable transducer system performance by adhering to the following engineering guidelines:\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProbe Gap Calibration:\u003c\/strong\u003e Mount the probe with the correct initial mechanical gap (typically 1.27 mm or 50 mils) to target the midpoint of the Proximitor sensor's calibrated linear voltage range.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eThread Integrity:\u003c\/strong\u003e Use care when threading the probe into brackets or casings. Do not exceed recommended tightening torque to prevent thread damage.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCable Protection:\u003c\/strong\u003e Route the standard unarmored coaxial cable inside rigid or flexible conduit to protect it from mechanical wear, pinching, and high temperatures.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eConnector Protection:\u003c\/strong\u003e Verify that the integrated connector protector is properly seated to insulate the ClickLoc junction from lubricating oil, moisture, and debris.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eGrounding and Shielding:\u003c\/strong\u003e Properly terminate cable shields at the instrument\/monitor end of the loop only, preventing ground loops that introduce electronic noise.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666529120619,"sku":"330101-02-21-10-01-00","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330101-02-21-10-01-00-proximity-probe-f0bf1dmjmxw_e7b05a45-1859-4c42-bab1-7ba26740bd05.jpg?v=1765440324"},{"product_id":"bently-nevada-330104-00-07-10-02-05-3300-xl-8-mm-proximity-probe-with-armor","title":"Bently Nevada 330104-00-07-10-02-05 3300 XL 8 mm Proximity Probe with Armor","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e330104-00-07-10-02-05\u003c\/strong\u003e specifies a \u003cstrong\u003e3300 XL 8 mm proximity probe\u003c\/strong\u003e configured with M10 x 1 metric threads, a fully threaded 70 mm case, integrated stainless steel armor, a 1.0-meter overall length, and CSA, ATEX, and IECEx approvals.\u003c\/p\u003e\n\u003cp\u003eThis configuration incorporates an unarmored tip followed by a stainless steel armored cable jacket to withstand harsh industrial wear. The miniature coaxial ClickLoc connector is supplied without a connector protector (Option 02) and connects standard coaxial field wiring to a Proximitor sensor. It operates as part of an eddy-current transducer system to monitor machinery shaft vibration, position, or speed.\u003c\/p\u003e\n\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eM10 x 1 metric thread structure with 0 mm unthreaded length (Option 00) for complete thread engagement.\u003c\/li\u003e\n  \u003cli\u003e70 mm overall case length (Option 07) suitable for shallow-depth machine case installations.\u003c\/li\u003e\n  \u003cli\u003e1.0 meter (3.3 feet) overall system cable length (Option 10) matching 9-meter or 5-meter monitoring system requirements.\u003c\/li\u003e\n  \u003cli\u003eStainless steel armored cable provides mechanical protection against abrasion and physical damage.\u003c\/li\u003e\n  \u003cli\u003eMiniature coaxial ClickLoc connector (Option 02) offers tool-free gold-plated click connection.\u003c\/li\u003e\n  \u003cli\u003eAgency approval Option 05 qualifies the probe for ATEX, IECEx, and CSA hazardous location installations.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cp\u003eThis proximity probe is used in machinery protection systems to monitor rotating equipment parameters. Common industrial deployments include:\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eRadial shaft vibration monitoring on steam turbines, gas turbines, and industrial compressors.\u003c\/li\u003e\n  \u003cli\u003eAxial thrust position tracking on high-speed pumps and gearboxes.\u003c\/li\u003e\n  \u003cli\u003eKeyphasor and speed measurements on industrial machinery shafts.\u003c\/li\u003e\n  \u003cli\u003eMachinery condition monitoring in petrochemical, power generation, and water treatment plants.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eOption Segment\u003c\/th\u003e\n      \u003cth\u003eCode Value\u003c\/th\u003e\n      \u003cth\u003eMeaning \/ Description\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOrderable Part Number\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330104-00-07-10-02-05\u003c\/td\u003e\n      \u003ctd\u003e3300 XL 8 mm probe, M10 x 1 thread, with armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eA - Unthreaded Length Option\u003c\/td\u003e\n      \u003ctd\u003e00\u003c\/td\u003e\n      \u003ctd\u003e0 mm (fully threaded case)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eB - Overall Case Length Option\u003c\/td\u003e\n      \u003ctd\u003e07\u003c\/td\u003e\n      \u003ctd\u003e70 mm case length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eC - Total Length Option\u003c\/td\u003e\n      \u003ctd\u003e10\u003c\/td\u003e\n      \u003ctd\u003e1.0 meter (3.3 feet) total length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eD - Connector and Cable-Type Option\u003c\/td\u003e\n      \u003ctd\u003e02\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector, standard cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eE - Agency Approval Option\u003c\/td\u003e\n      \u003ctd\u003e05\u003c\/td\u003e\n      \u003ctd\u003eCSA, ATEX, IECEx Approvals\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eParameter\u003c\/th\u003e\n      \u003cth\u003eSpecification Value\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eManufacturer\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eBently Nevada (Baker Hughes)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003ePart Number\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330104-00-07-10-02-05\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProduct Series\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e3300 XL 8 mm Proximity Transducer System\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eThread Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eM10 x 1 metric thread\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eUnthreaded Length (Option A)\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e0 mm\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eCase Length (Option B)\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e70 mm\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eTotal Probe Length (Option C)\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e1.0 meter (3.3 feet)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eConnector Type (Option D)\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector, standard cable (no connector protector)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eArmor Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eIntegrated stainless steel armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eAgency Approvals (Option E)\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eCSA, ATEX, IECEx hazardous area approvals\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eNominal Probe DC Resistance\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e7.59 ohms +\/- 0.50 ohms (center conductor to outer conductor)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOperating Temperature Range\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e-52 degC to +177 degC (-62 degF to +350 degF)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eDifferential Pressure Seal\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eDesigned to seal up to 10.3 bar (150 psi) using Viton O-ring\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Tip Diameter\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e8.0 mm (0.31 in)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eMinimum Target Size\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e15.2 mm (0.6 in) diameter (AISI 4140 steel target)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eDimensions\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e105 mm x 105 mm x 25 mm (H x W x D)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eWeight\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e0.15 kg\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eVerify that the total combined length of the probe and extension cable matches the calibrated length of the Proximitor sensor (typically 5 or 9 meters total).\u003c\/li\u003e\n  \u003cli\u003eEnsure correct probe gap during installation (typically gapped at 1.27 mm or 50 mils for mid-range operation).\u003c\/li\u003e\n  \u003cli\u003eTighten the M10 x 1 threads to the proper installation torque; do not exceed 15 Nm (11 ft-lb) to avoid case damage.\u003c\/li\u003e\n  \u003cli\u003eEnsure the miniature coaxial ClickLoc connectors are connected finger-tight. Avoid using heavy pliers which can damage the gold plating.\u003c\/li\u003e\n  \u003cli\u003eRoute the armored cable away from sharp edges, high-temperature conduits, and high-voltage power sources to minimize electrical noise interference.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eCompliance and Certifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eATEX: Flameproof and intrinsically safe approvals for hazardous zones (with compatible barriers)\u003c\/li\u003e\n  \u003cli\u003eIECEx: International hazardous area certification\u003c\/li\u003e\n  \u003cli\u003eCSA: North American safety approval for Class I, Division 1 and Division 2 locations\u003c\/li\u003e\n  \u003cli\u003eCE: Conformity marking for electromagnetic compatibility\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666529186155,"sku":"330104-00-07-10-02-05","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330104-00-07-10-02-05-proximity-probes-bug1ykziezs_443d9687-acdc-4471-91df-1fcd49568ba0.jpg?v=1765440325"},{"product_id":"bently-nevada-330102-04-45-50-01-00-3300-xl-8-mm-proximity-probe","title":"Bently Nevada 330102-04-45-50-01-00 3300 XL 8 mm Proximity Probe","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\n\u003cp\u003eSteel probe case with 3\/8-24 UNF threads featuring a 0.4 in unthreaded length (Option 04) and a 4.5 in overall case length (Option 45) — \u003cstrong\u003e330102-04-45-50-01-00\u003c\/strong\u003e \u003cstrong\u003eproximity probe\u003c\/strong\u003e.\u003c\/p\u003e\n\u003cp\u003eEquipped with stainless steel armor for robust mechanical protection, this configuration includes a miniature coaxial ClickLoc connector with an integrated connector protector (Option 01). The 5.0-meter total length (Option 50) means the probe connects directly to a 5-meter 3300 XL Proximitor sensor, eliminating the need for a separate extension cable. Operating as an eddy-current system, it provides continuous shaft vibration, axial position, and speed measurements on rotating machinery.\u003c\/p\u003e\n\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e3\/8-24 UNF threaded steel probe case with robust stainless steel armor.\u003c\/li\u003e\n  \u003cli\u003e0.4 in unthreaded length (Option 04) for precise clearance adjustment.\u003c\/li\u003e\n  \u003cli\u003e4.5 in overall case length (Option 45).\u003c\/li\u003e\n  \u003cli\u003e5.0 m total length (Option 50) designed to connect directly to a matching 5-meter Proximitor sensor.\u003c\/li\u003e\n  \u003cli\u003eClickLoc coaxial connector featuring a fluorosilicone connector protector (Option 01) to seal out moisture.\u003c\/li\u003e\n  \u003cli\u003eUnapproved variant (Option 00) for standard non-hazardous industrial environments.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eSteam and gas turbine shaft vibration and position monitoring.\u003c\/li\u003e\n  \u003cli\u003eHydroelectric turbine shaft displacement tracking.\u003c\/li\u003e\n  \u003cli\u003eBoiler feed pump axial position thrust measurements.\u003c\/li\u003e\n  \u003cli\u003eLarge industrial compressor and blower vibration protection.\u003c\/li\u003e\n  \u003cli\u003eGearbox shaft dynamic motion monitoring.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eOption \/ Segment\u003c\/th\u003e\n      \u003cth\u003eCode on This SKU\u003c\/th\u003e\n      \u003cth\u003eDescription\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOrderable Part Number\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330102-04-45-50-01-00\u003c\/td\u003e\n      \u003ctd\u003e3300 XL 8 mm Proximity Probe, 3\/8-24 UNF thread, with armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eA - Unthreaded Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e04\u003c\/td\u003e\n      \u003ctd\u003e0.4 in unthreaded length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eB - Case Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e45\u003c\/td\u003e\n      \u003ctd\u003e4.5 in overall case length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eC - Total Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e50\u003c\/td\u003e\n      \u003ctd\u003e5.0 meters (16.4 feet) total length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eD - Connector and Cable-Type Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e01\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector with connector protector, standard cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eE - Agency Approval Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e00\u003c\/td\u003e\n      \u003ctd\u003eAgency approval not required\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eParameter\u003c\/th\u003e\n      \u003cth\u003eSpecification\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eManufacturer\u003c\/td\u003e\n      \u003ctd\u003eBently Nevada (Baker Hughes)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eModel \/ Part Number\u003c\/td\u003e\n      \u003ctd\u003e330102-04-45-50-01-00\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eTransducer Type\u003c\/td\u003e\n      \u003ctd\u003eNon-contact eddy-current proximity probe\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eProbe Tip Diameter\u003c\/td\u003e\n      \u003ctd\u003e8.0 mm (0.31 in)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eCase Thread Size\u003c\/td\u003e\n      \u003ctd\u003e3\/8-24 UNF-2A\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eUnthreaded Length\u003c\/td\u003e\n      \u003ctd\u003e0.4 in (10.2 mm)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eOverall Case Length\u003c\/td\u003e\n      \u003ctd\u003e4.5 in (114.3 mm)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eTotal Cable Length\u003c\/td\u003e\n      \u003ctd\u003e5.0 meters (16.4 feet)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eCable Type\u003c\/td\u003e\n      \u003ctd\u003eStandard cable with stainless steel armor and FEP outer jacket\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eConnector Type\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eConnector Protector\u003c\/td\u003e\n      \u003ctd\u003eIncluded (Fluorosilicone material)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eAgency Approval\u003c\/td\u003e\n      \u003ctd\u003eNone (Option 00)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eOperating Temperature\u003c\/td\u003e\n      \u003ctd\u003e-52 degC to +177 degC\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eDifferential Pressure Seal\u003c\/td\u003e\n      \u003ctd\u003eUp to 70 psi (4.8 bar) across probe tip\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eProbe Case Material\u003c\/td\u003e\n      \u003ctd\u003e303 Stainless Steel\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eProbe Tip Material\u003c\/td\u003e\n      \u003ctd\u003ePolyphenylene sulfide (PPS)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eMinimum Cable Bend Radius\u003c\/td\u003e\n      \u003ctd\u003e25.4 mm (1.0 in)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eWeight\u003c\/td\u003e\n      \u003ctd\u003e0.60 kg\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eDimensions\u003c\/td\u003e\n      \u003ctd\u003e9.5 mm x 9.5 mm x 114.3 mm (H x W x D)\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eConnections and Interfaces\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eConnector Component\u003c\/th\u003e\n      \u003cth\u003eConnection Type \/ Details\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eProbe Connector\u003c\/td\u003e\n      \u003ctd\u003eMiniature male coaxial ClickLoc connector with gold-plated brass body\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eExtension Interface\u003c\/td\u003e\n      \u003ctd\u003eConnects directly to female ClickLoc connector of a 5-meter Proximitor Sensor\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eSecure the probe housing using a 9\/16 inch lock nut (supplied).\u003c\/li\u003e\n  \u003cli\u003eVerify that the unthreaded length is at least 0.8 in less than the overall case length to maintain physical housing stability.\u003c\/li\u003e\n  \u003cli\u003eMaintain a minimum cable bend radius of 25.4 mm (1.0 in) to prevent damaging the internal coaxial core and outer armor.\u003c\/li\u003e\n  \u003cli\u003eHand-tighten ClickLoc connectors to click feedback. Do not use tools on the gold-plated connectors.\u003c\/li\u003e\n  \u003cli\u003eRun probe cables through dedicated, grounded conduits to avoid electromagnetic interference.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eCompliance and Certifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eCE Compliant\u003c\/li\u003e\n  \u003cli\u003eRoHS Compliant\u003c\/li\u003e\n  \u003cli\u003eManufactured under ISO 9001 certified quality standards\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666529349995,"sku":"330102-04-45-50-01-00","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330102-04-45-50-01-00-high-speed-sensor-monitoring-module-eb1pwa34vxd_78bc51bc-25c2-4c22-a8d5-7ef59edc1257.jpg?v=1765440328"},{"product_id":"bently-nevada-330101-00-72-10-12-05-3300-xl-8-mm-proximity-probe","title":"Bently Nevada 330101-00-72-10-12-05 3300 XL 8 mm Proximity Probe","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eBently Nevada 330101-00-72-10-12-05\u003c\/strong\u003e is an eddy-current-based \u003cstrong\u003e3300 XL 8 mm Proximity Probe\u003c\/strong\u003e designed for non-contact shaft vibration and position monitoring in critical rotating machinery. Unlike armored configurations, this variant features a lightweight, flexible, unarmored body with standard 3\/8-24 UNF threads, 0.0 inches of unthreaded length, and a 7.2-inch case length to suit deep-well housing installations. A key distinguishing feature of this configuration is its 1.0-meter (3.3 feet) integrated FluidLoc cable with a miniature coaxial ClickLoc connector. The patented FluidLoc cable utilizes an internal sealing process that blocks lubrication oil and other process liquids from migrating along the cable's interior, providing exceptional protection against leakage out of pressurized machine casings. This probe is equipped with the -05 agency approval option, certifying it under international CSA, ATEX, and IECEx hazardous area safety standards for reliable operation in explosive environments.\u003c\/p\u003e\n\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e8 mm tip diameter proximity probe optimized for accurate, non-contact displacement and dynamic vibration measurement.\u003c\/li\u003e\n  \u003cli\u003eFully threaded 3\/8-24 UNF stainless steel case with 0.0 in unthreaded length and 7.2 in overall case length.\u003c\/li\u003e\n  \u003cli\u003eFluidLoc cable design prevents machinery oil and other liquid media from escaping pressurized housings via the cable's internal core.\u003c\/li\u003e\n  \u003cli\u003eGold-plated miniature ClickLoc coaxial connector provides secure, finger-tight locking without requiring specialized installation tools.\u003c\/li\u003e\n  \u003cli\u003eRobust PPS (polyphenylene sulfide) tip material and AISI 303 stainless steel body withstand harsh industrial conditions.\u003c\/li\u003e\n  \u003cli\u003eBroad temperature operating envelope from -52 degC to +177 degC.\u003c\/li\u003e\n  \u003cli\u003eCertified under major hazardous area standards including ATEX, IECEx, and CSA.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cp\u003eThe Bently Nevada 330101-00-72-10-12-05 probe is primarily deployed in demanding industrial environments where continuous machine protection is crucial:\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eRadial vibration and axial displacement monitoring on steam and gas turbines.\u003c\/li\u003e\n  \u003cli\u003eRotor position and casing expansion tracking in high-pressure compressors, turbo-expanders, and pumps.\u003c\/li\u003e\n  \u003cli\u003eMachinery housings requiring tight oil containment, such as oil-filled turbine bearings or flooded gearboxes.\u003c\/li\u003e\n  \u003cli\u003ePermanent installations in petrochemical plants, refineries, pipelines, and power generation facilities requiring certified intrinsically safe components.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eOption \/ Segment\u003c\/th\u003e\n      \u003cth\u003eCode on This SKU\u003c\/th\u003e\n      \u003cth\u003eDescription \/ Meaning\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOrderable Part Number\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330101-00-72-10-12-05\u003c\/td\u003e\n      \u003ctd\u003e3300 XL 8 mm Proximity Probe, 3\/8-24 UNF thread, without armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eA - Unthreaded Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e00\u003c\/td\u003e\n      \u003ctd\u003e0.0 in (0 mm) unthreaded length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eB - Overall Case Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e72\u003c\/td\u003e\n      \u003ctd\u003e7.2 in (183 mm) case length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eC - Total Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e10\u003c\/td\u003e\n      \u003ctd\u003e1.0 meter (3.3 feet) total length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eD - Connector and Cable Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e12\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector, FluidLoc cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eE - Agency Approval Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e05\u003c\/td\u003e\n      \u003ctd\u003eCSA, ATEX, IECEx Approvals\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eManufacturer\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eBently Nevada\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003ePart Number \/ Model\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330101-00-72-10-12-05\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProduct Series\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e3300 XL 8 mm Proximity Transducer System\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eMeasurement Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eDisplacement (proximity), vibration, speed, and phase reference\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOperating Principle\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eEddy current\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Tip Diameter\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e8 mm\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eThread Specification\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e3\/8-24 UNF-2A threads\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eCase Configuration\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e7.2 in (183 mm) overall case length, fully threaded (0.0 in unthreaded length)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eArmor Protection\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eUnarmored (without armor)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eCable Construction\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e1.0 meter (3.3 feet) FluidLoc cable (prevents internal oil migration)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eConnector Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector (gold-plated)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eMaterial Construction\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003ePolyphenylene sulfide (PPS) probe tip; AISI 303 stainless steel probe body\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Operating Temperature\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e-52 degC to +177 degC (-62 degF to +350 degF)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Pressure Rating\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eSealed against differential pressure between tip and case (Viton O-ring design)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eDimensions\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e45 mm x 95 mm x 95 mm (H x W x D)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eWeight\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e0.14 kg\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\n\u003cp\u003eTo ensure precise performance of the 3300 XL proximity transducer system, follow these general engineering rules:\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eVerify that the mounting thread matches the probe's 3\/8-24 UNF profile and has adequate depth (maximum recommended thread engagement of 0.563 inches in standard mounts).\u003c\/li\u003e\n  \u003cli\u003eSet the target-to-probe gap carefully during installation. Standard calibration uses an AISI 4140 steel target with a standard gap offset corresponding to roughly -10 Vdc (1.27 mm or 50 mils) output at the Proximitor sensor.\u003c\/li\u003e\n  \u003cli\u003eEnsure lock nuts with pre-drilled safety wire holes are secured tightly to prevent loosening under heavy vibration.\u003c\/li\u003e\n  \u003cli\u003eProtect standard ClickLoc coaxial connectors from dirt, grease, and mechanical strain. Avoid bending the FluidLoc cable below its minimum bend radius during installation routing.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eCompliance and Certifications\u003c\/h3\u003e\n\u003cp\u003eThis product configuration complies with the following industry approvals:\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eHazardous Area Approvals (Option 05):\u003c\/strong\u003e Certified for intrinsically safe and non-incendive environments under CSA, ATEX, and IECEx (e.g., Ex ia IIC T1...T5 Ga, Ex nA IIC T1...T5 Gc).\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eElectromagnetic Compatibility:\u003c\/strong\u003e Complies with European Union EMC Directive 2014\/30\/EU standards including EN 61000-6-2 (Immunity) and EN 61000-6-4 (Emissions).\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eEnvironmental Compliance:\u003c\/strong\u003e European Union RoHS Directive 2011\/65\/EU and China RoHS compliance with an EFUP rating of 15 years.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eFunctional Safety:\u003c\/strong\u003e SIL 2 (HFT = 0) and SIL 3 (HFT = 1) certified for safety instrumented systems.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666529382763,"sku":"330101-00-72-10-12-05","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330101-00-72-10-12-05-probe-kr4xc2alh0e_4a3d1182-b13e-40a5-99c0-258ce29d63f3.jpg?v=1765440329"},{"product_id":"bently-nevada-330902-00-38-05-02-05-3300-nsv-proximity-probe","title":"Bently Nevada 330902-00-38-05-02-05 3300 NSv Proximity Probe","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e330902-00-38-05-02-05\u003c\/strong\u003e specifies a 3300 NSv proximity probe configured with a 1\/4-28 UNF thread and protective stainless steel armor. This specific configuration features a 0.0-inch unthreaded length (Option 00), a 3.8-inch overall case length (Option 38), a 0.5-meter (20-inch) total length (Option 05), a miniature coaxial ClickLoc connector on standard cable (Option 02), and multiple agency hazardous area approvals (Option 05).\u003c\/p\u003e\n\u003cp\u003eDesigned for non-contact displacement measurements in machinery with tight physical clearances, the 3300 NSv transducer system replaces older 3300 RAM and 3000\/7000-series systems. This configuration uses its integrated stainless steel armor to shield the coaxial cable against mechanical wear, abrasion, and debris in small-bore rotating machinery such as centrifugal compressors.\u003c\/p\u003e\n\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eOption 00 specifies a 0.0-inch unthreaded portion, making the probe body fully threaded.\u003c\/li\u003e\n  \u003cli\u003eOption 38 provides a 3.8-inch overall case length with a 1\/4-28 UNF-2A thread.\u003c\/li\u003e\n  \u003cli\u003eOption 05 establishes a total probe length of 0.5 meters (20 inches) to prevent excessive internal cabling.\u003c\/li\u003e\n  \u003cli\u003eOption 02 includes a miniature coaxial ClickLoc connector with standard FEP-jacketed cable.\u003c\/li\u003e\n  \u003cli\u003eOption 05 multiple approvals package covers CSA, ATEX, and IECEx certifications for hazardous environments.\u003c\/li\u003e\n  \u003cli\u003eIntegrated stainless steel armor provides physical cable protection from crushing and abrasion.\u003c\/li\u003e\n  \u003cli\u003eViton O-ring tip seal prevents differential pressure leakage between the probe tip and the machine case.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cp\u003eThe 3300 NSv proximity probe is primarily used in fluid-filmed bearing machines with small shaft diameters or restricted side-view access. Key applications include:\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eCentrifugal air compressors and refrigeration compressors\u003c\/li\u003e\n  \u003cli\u003eSmall-bore machinery and high-speed equipment with limited target geometry\u003c\/li\u003e\n  \u003cli\u003eRadial vibration and radial position measurements\u003c\/li\u003e\n  \u003cli\u003eAxial (thrust) position measurements\u003c\/li\u003e\n  \u003cli\u003eTachometer, zero speed, and phase reference (Keyphasor) signal generation\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eOption \/ Segment\u003c\/th\u003e\n      \u003cth\u003eCode on This SKU\u003c\/th\u003e\n      \u003cth\u003eMeaning \/ Description\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eBase Model\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330902\u003c\/td\u003e\n      \u003ctd\u003e3300 NSv Probe, 1\/4-28 UNF thread, with stainless steel armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eA - Unthreaded Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e00\u003c\/td\u003e\n      \u003ctd\u003e0.0 inches unthreaded length (fully threaded case)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eB - Overall Case Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e38\u003c\/td\u003e\n      \u003ctd\u003e3.8 inches (97 mm) overall case length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eC - Total Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e05\u003c\/td\u003e\n      \u003ctd\u003e0.5 meters (20 inches) total length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eD - Connector and Cable Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e02\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector, standard cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eE - Agency Approval Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e05\u003c\/td\u003e\n      \u003ctd\u003eMultiple Approvals (including CSA, ATEX, IECEx)\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eParameter\u003c\/th\u003e\n      \u003cth\u003eSpecification Value\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eManufacturer\u003c\/td\u003e\n      \u003ctd\u003eBently Nevada (Baker Hughes)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003ePart Number \/ SKU\u003c\/td\u003e\n      \u003ctd\u003e330902-00-38-05-02-05\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eThread Type\u003c\/td\u003e\n      \u003ctd\u003e1\/4-28 UNF-2A\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eArmor Material\u003c\/td\u003e\n      \u003ctd\u003eStainless steel armor (uncoated)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eUnthreaded Length\u003c\/td\u003e\n      \u003ctd\u003e0.0 in (0 mm)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eCase Length\u003c\/td\u003e\n      \u003ctd\u003e3.8 in (97 mm)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eTotal Length\u003c\/td\u003e\n      \u003ctd\u003e0.5 meters (20 inches)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eConnector Type\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc male connector\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eCable Type\u003c\/td\u003e\n      \u003ctd\u003e75 ohm coaxial cable (FEP insulated)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eTarget Material Calibration\u003c\/td\u003e\n      \u003ctd\u003eAISI 4140 steel\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eLinear Range\u003c\/td\u003e\n      \u003ctd\u003e1.5 mm (60 mils), from approximately 0.25 to 1.75 mm (10 to 70 mils)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eRecommended Probe Gap\u003c\/td\u003e\n      \u003ctd\u003e1.0 mm (40 mils)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eIncremental Scale Factor (ISF)\u003c\/td\u003e\n      \u003ctd\u003e7.87 V\/mm (200 mV\/mil) nominal\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eDeviation from Best Fit Straight Line (DSL)\u003c\/td\u003e\n      \u003ctd\u003eLess than +\/-0.06 mm (+\/-2.3 mils) over linear range\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eProbe DC Resistance\u003c\/td\u003e\n      \u003ctd\u003eConductor to shield: 4.0 +\/- 0.5 ohms\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eOutput Impedance\u003c\/td\u003e\n      \u003ctd\u003e50 ohms (Proximitor Sensor)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eOperating\/Storage Temperature\u003c\/td\u003e\n      \u003ctd\u003e-52 degC to +177 degC (-62 degF to +351 degF)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eHumidity Resistance\u003c\/td\u003e\n      \u003ctd\u003e100% condensing, non-submersible with protected connectors\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003ePressure Seal Rating\u003c\/td\u003e\n      \u003ctd\u003eViton O-ring differential pressure seal\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eFrequency Response\u003c\/td\u003e\n      \u003ctd\u003e0 to 10 kHz: +0, -3 dB typical\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\n\u003cp\u003eTo ensure precise performance and long operational life, adhere to these technical installation practices:\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eWhen drilling and tapping holes for a 1\/4-28 probe, a #3 or larger tap drill is recommended.\u003c\/li\u003e\n  \u003cli\u003eDo not exceed the maximum recommended torque of 5.1 N-m (45 in-lb) or the absolute maximum rated torque of 7.3 N-m (65 in-lb) on 1\/4-28 probe cases during installation.\u003c\/li\u003e\n  \u003cli\u003eEnsure the coaxial cable maintains a minimum bend radius of 25.4 mm (1.0 inch).\u003c\/li\u003e\n  \u003cli\u003eProtect all electrical connections from environmental humidity and oil ingress by installing a connector protector kit or applying silicone self-fusing tape.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eCompliance and Certifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eEMC Standards:\u003c\/strong\u003e EN 61000-6-2 (Industrial Immunity), EN 61000-6-4 (Industrial Emissions)\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eEnvironmental Compliance:\u003c\/strong\u003e RoHS Directive 2011\/65\/EU; China RoHS EFUP designation of 15 years\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eFunctional Safety:\u003c\/strong\u003e SIL 2 certified (HFT = 0), SIL 3 certified (HFT = 1)\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eHazardous Area Approvals (Option 05 Multiple Approvals):\u003c\/strong\u003e Intrinsically Safe (Ex ia) and Non-sparking\/Increased Safety (Ex nA\/Ex ec) under ATEX, IECEx, and CSA standards for Zone 0, Zone 2, and Class I Division 1\/2 areas\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666529415531,"sku":"330902-00-38-05-02-05","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330902-00-38-05-02-05-proximity-transducer-driver-module-g1umh2wjrxt_77152006-f3c5-49f1-8208-34f5703cbe9b.jpg?v=1765440330"},{"product_id":"bently-nevada-330101-00-80-10-02-00-3300-xl-8-mm-proximity-probe","title":"Bently Nevada 330101-00-80-10-02-00 3300 XL 8 mm Proximity Probe","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\n\u003cp\u003eEngineered for high-precision rotating machinery monitoring, the \u003cstrong\u003eBently Nevada 330101-00-80-10-02-00\u003c\/strong\u003e is an eddy-current \u003cstrong\u003e8 mm proximity probe\u003c\/strong\u003e designed for non-contact shaft vibration and position measurement. This exact configuration is built with a standard 3\/8-24 UNF thread housing and is fully threaded (0.0 inches of unthreaded length), presenting an extended 8.0-inch overall case length. It integrates a 1.0-meter standard coaxial cable without armor, terminated in a miniature ClickLoc connector. Free of hazardous area approvals, this specific variant is optimized for cost-effective installation in general-purpose industrial environments where mechanical armor or connector protectors are not required.\u003c\/p\u003e\n\u003cp\u003eAs a key component of the 3300 XL 8 mm Proximity Transducer System, this probe operates on the eddy-current principle to measure static and dynamic distances between the probe tip and a conductive target, typically an AISI 4140 steel shaft. It pairs seamlessly with a 3300 XL Proximitor sensor and a corresponding extension cable, providing a linear range of 2.0 mm (80 mils) with an incremental scale factor of 7.87 V\/mm (200 mV\/mil). This system delivers highly accurate displacement readings that are essential for machinery protection and predictive maintenance systems, such as the Bently Nevada 3500 series rack.\u003c\/p\u003e\n\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eFully threaded case (0.0 in unthreaded length) and long 8.0 in overall housing, ideal for deep bearing housings.\u003c\/li\u003e\n  \u003cli\u003e1.0 meter (3.3 feet) standard unarmored coaxial cable configuration.\u003c\/li\u003e\n  \u003cli\u003eStandard miniature coaxial ClickLoc connector provides low-profile connection to extension cables.\u003c\/li\u003e\n  \u003cli\u003eHigh-performance eddy-current transducer technology delivers reliable non-contact measurement.\u003c\/li\u003e\n  \u003cli\u003eFull compatibility with Bently Nevada 3300 XL monitoring systems and 3500 rack modules.\u003c\/li\u003e\n  \u003cli\u003eViton O-ring design provides high-resistance sealing against differential pressure.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eSteam and gas turbine radial shaft vibration monitoring.\u003c\/li\u003e\n  \u003cli\u003eCompressor, expander, and pump shaft axial position and displacement measurement.\u003c\/li\u003e\n  \u003cli\u003eThrust bearing wear and rotor dynamic tracking in large rotating machinery.\u003c\/li\u003e\n  \u003cli\u003ePermanent machinery protection installations on industrial bearing casings.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eOption Code\u003c\/th\u003e\n      \u003cth\u003eThis SKU Value\u003c\/th\u003e\n      \u003cth\u003eMeaning \/ Specification (from Datasheet)\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOrderable Part Number\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330101-00-80-10-02-00\u003c\/td\u003e\n      \u003ctd\u003e3300 XL 8 mm Proximity Probe, 3\/8-24 UNF thread, without armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eA - Unthreaded Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e00\u003c\/td\u003e\n      \u003ctd\u003e0.0 in (0 mm) unthreaded length (fully threaded housing)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eB - Overall Case Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e80\u003c\/td\u003e\n      \u003ctd\u003e8.0 in (203 mm) overall case length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eC - Total Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e10\u003c\/td\u003e\n      \u003ctd\u003e1.0 meter (3.3 feet) probe total length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eD - Connector and Cable\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e02\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector, standard cable (no armor, no connector protector)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eE - Agency Approval\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e00\u003c\/td\u003e\n      \u003ctd\u003eNot required (general-purpose safe area installation)\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eParameter\u003c\/th\u003e\n      \u003cth\u003eValue \/ Specification\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eManufacturer\u003c\/td\u003e\n      \u003ctd\u003eBently Nevada\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eModel Number\u003c\/td\u003e\n      \u003ctd\u003e330101-00-80-10-02-00\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eProduct Family\u003c\/td\u003e\n      \u003ctd\u003e3300 XL 8 mm Proximity Transducer System\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eProbe Diameter\u003c\/td\u003e\n      \u003ctd\u003e8 mm\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eMeasurement Type\u003c\/td\u003e\n      \u003ctd\u003eDisplacement (proximity)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eOperating Principle\u003c\/td\u003e\n      \u003ctd\u003eEddy current\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eLinear Range\u003c\/td\u003e\n      \u003ctd\u003e2.0 mm (80 mils), from approximately 0.25 mm to 2.25 mm (10 to 90 mils)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eIncremental Scale Factor (ISF)\u003c\/td\u003e\n      \u003ctd\u003e7.87 V\/mm (200 mV\/mil) nominal\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eStandard Case Thread\u003c\/td\u003e\n      \u003ctd\u003e3\/8-24 UNF-2A (without armor)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eUnthreaded Case Length\u003c\/td\u003e\n      \u003ctd\u003e0.0 in (0 mm)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eOverall Case Length\u003c\/td\u003e\n      \u003ctd\u003e8.0 in (203 mm)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eProbe Cable Length\u003c\/td\u003e\n      \u003ctd\u003e1.0 meter (3.3 feet)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eConnector Type\u003c\/td\u003e\n      \u003ctd\u003eMiniature ClickLoc coaxial connector\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eProbe Temperature Range\u003c\/td\u003e\n      \u003ctd\u003e-52 degC to +177 degC (-62 degF to +350 degF) operating and storage\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eNominal Probe DC Resistance\u003c\/td\u003e\n      \u003ctd\u003e7.59 ohms +\/- 0.50 ohms (for 1.0 m length, center conductor to outer conductor)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eEnvironmental Protection\u003c\/td\u003e\n      \u003ctd\u003eViton O-ring probe tip-to-case pressure seal\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eWeight\u003c\/td\u003e\n      \u003ctd\u003e0.14 kg\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eDimensions\u003c\/td\u003e\n      \u003ctd\u003e45 mm x 95 mm x 95 mm (H x W x D)\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\n\u003cp\u003eTo ensure optimal performance and prevent premature failure of the 3300 XL proximity probe during installation, observe the following guidelines:\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProbe Gap:\u003c\/strong\u003e Mount the probe with the appropriate mechanical clearance gap (typically calibrated to -9 Vdc, or approximately 1.27 mm \/ 50 mils) corresponding to the target center-line of the linear range.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eThread Engagement:\u003c\/strong\u003e Do not exceed the maximum recommended thread engagement of 0.563 inches for 3\/8-24 threads to prevent binding.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCable Routing:\u003c\/strong\u003e Always route the probe and extension cables with proper shielding, grounding, and isolation from high-voltage lines. Use conduits or cable trays to prevent mechanical damage.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eTorque Limits:\u003c\/strong\u003e Connectors should be finger-tight only. Do not use tools on the ClickLoc gold connectors to avoid damage to the gold plating and physical structure.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666529579371,"sku":"330101-00-80-10-02-00","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330101-00-80-10-02-00-8-mm-probe-4u5mjqy5nh3_f97d92ee-70bb-4f31-9605-8d278d1e7a0b.jpg?v=1765440335"},{"product_id":"bently-nevada-330104-07-14-05-01-00-3300-xl-8-mm-proximity-probe-with-armor","title":"Bently Nevada 330104-07-14-05-01-00 3300 XL 8 mm Proximity Probe with Armor","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\n\u003cp\u003eOption 07 (70 mm unthreaded length) and Option 01 (coaxial ClickLoc connector with connector protector, standard cable) specify this metric 3300 XL 8 mm probe configuration — \u003cstrong\u003e330104-07-14-05-01-00\u003c\/strong\u003e. This non-contact eddy-current sensor measures shaft vibration, axial position, and keyphasor reference on rotating machinery.\u003c\/p\u003e\n\n\u003cp\u003eFeaturing a heavy-duty stainless steel armored sheath, this variant provides enhanced mechanical shielding for the coaxial lead. This specific combination of a 140 mm case, 70 mm unthreaded segment, and 0.5-meter cable length matches specific machine housing geometries and integrates with 3300 XL Proximitor sensors and extension cables without requiring hazardous area agency approvals.\u003c\/p\u003e\n\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eStainless steel armor with FEP outer jacket provides protection from physical impact and chemical exposure.\u003c\/li\u003e\n  \u003cli\u003eOption 07 provides 70 mm of unthreaded length on a 140 mm overall metric case.\u003c\/li\u003e\n  \u003cli\u003eMetric thread configuration with M10 x 1 casing thread matches European and ISO machinery mounting standards.\u003c\/li\u003e\n  \u003cli\u003eOption 01 miniature coaxial ClickLoc connector includes a pre-installed fluorosilicone connector protector.\u003c\/li\u003e\n  \u003cli\u003eCompact 0.5-meter total cable length is suitable for direct connections to nearby junction boxes.\u003c\/li\u003e\n  \u003cli\u003eNo agency approvals (Option 00) for general purpose, non-hazardous area applications.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eShaft vibration and dynamic displacement measurements on steam and gas turbines.\u003c\/li\u003e\n  \u003cli\u003eAxial rotor position and thrust bearing wear monitoring in high-pressure compressors.\u003c\/li\u003e\n  \u003cli\u003eSpeed and tachometer measurements using keyphasor reference signals on industrial pumps.\u003c\/li\u003e\n  \u003cli\u003eMachinery protection systems within power generation, oil and gas, and petrochemical facilities.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003ctable border=\"1\" style=\"width:100%; border-collapse:collapse;\"\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth style=\"padding: 8px; text-align: left;\"\u003eOption Code Segment\u003c\/th\u003e\n      \u003cth style=\"padding: 8px; text-align: left;\"\u003eThis SKU Value\u003c\/th\u003e\n      \u003cth style=\"padding: 8px; text-align: left;\"\u003eDescription \/ Meaning\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd style=\"padding: 8px;\"\u003e\u003cstrong\u003eOrderable Part Number\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd style=\"padding: 8px;\"\u003e\u003cstrong\u003e330104-07-14-05-01-00\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd style=\"padding: 8px;\"\u003e3300 XL 8 mm probe, M10 x 1 thread, with stainless steel armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd style=\"padding: 8px;\"\u003eA - Unthreaded Length Option\u003c\/td\u003e\n      \u003ctd style=\"padding: 8px;\"\u003e07\u003c\/td\u003e\n      \u003ctd style=\"padding: 8px;\"\u003e70 mm unthreaded segment length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd style=\"padding: 8px;\"\u003eB - Overall Case Length Option\u003c\/td\u003e\n      \u003ctd style=\"padding: 8px;\"\u003e14\u003c\/td\u003e\n      \u003ctd style=\"padding: 8px;\"\u003e140 mm overall case length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd style=\"padding: 8px;\"\u003eC - Total Length Option\u003c\/td\u003e\n      \u003ctd style=\"padding: 8px;\"\u003e05\u003c\/td\u003e\n      \u003ctd style=\"padding: 8px;\"\u003e0.5 meter (1.6 feet) cable length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd style=\"padding: 8px;\"\u003eD - Connector and Cable Option\u003c\/td\u003e\n      \u003ctd style=\"padding: 8px;\"\u003e01\u003c\/td\u003e\n      \u003ctd style=\"padding: 8px;\"\u003eMiniature ClickLoc coaxial connector with connector protector, standard cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd style=\"padding: 8px;\"\u003eE - Agency Approval Option\u003c\/td\u003e\n      \u003ctd style=\"padding: 8px;\"\u003e00\u003c\/td\u003e\n      \u003ctd style=\"padding: 8px;\"\u003eNo agency approvals required\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable border=\"1\" style=\"width:100%; border-collapse:collapse;\"\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd style=\"padding: 8px; font-weight: bold;\"\u003eManufacturer\u003c\/td\u003e\n      \u003ctd style=\"padding: 8px;\"\u003eBently Nevada (Baker Hughes)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd style=\"padding: 8px; font-weight: bold;\"\u003eModel Number\u003c\/td\u003e\n      \u003ctd style=\"padding: 8px;\"\u003e330104-07-14-05-01-00\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd style=\"padding: 8px; font-weight: bold;\"\u003eProduct Type\u003c\/td\u003e\n      \u003ctd style=\"padding: 8px;\"\u003e3300 XL 8 mm Proximity Probe\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd style=\"padding: 8px; font-weight: bold;\"\u003eThread Size\u003c\/td\u003e\n      \u003ctd style=\"padding: 8px;\"\u003eM10 x 1 metric thread\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd style=\"padding: 8px; font-weight: bold;\"\u003eArmoring\u003c\/td\u003e\n      \u003ctd style=\"padding: 8px;\"\u003eFlexible stainless steel armor with FEP outer jacket\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd style=\"padding: 8px; font-weight: bold;\"\u003eUnthreaded Length\u003c\/td\u003e\n      \u003ctd style=\"padding: 8px;\"\u003e70 mm\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd style=\"padding: 8px; font-weight: bold;\"\u003eOverall Case Length\u003c\/td\u003e\n      \u003ctd style=\"padding: 8px;\"\u003e140 mm\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd style=\"padding: 8px; font-weight: bold;\"\u003eTotal Cable Length\u003c\/td\u003e\n      \u003ctd style=\"padding: 8px;\"\u003e0.5 meter (1.6 feet)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd style=\"padding: 8px; font-weight: bold;\"\u003eCable Type\u003c\/td\u003e\n      \u003ctd style=\"padding: 8px;\"\u003e75 Ohm coaxial cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd style=\"padding: 8px; font-weight: bold;\"\u003eConnector Type\u003c\/td\u003e\n      \u003ctd style=\"padding: 8px;\"\u003eMiniature coaxial ClickLoc male connector\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd style=\"padding: 8px; font-weight: bold;\"\u003eConnector Protector\u003c\/td\u003e\n      \u003ctd style=\"padding: 8px;\"\u003ePre-installed on connector end\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd style=\"padding: 8px; font-weight: bold;\"\u003eOperating Temperature\u003c\/td\u003e\n      \u003ctd style=\"padding: 8px;\"\u003e-52 degC to +177 degC\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd style=\"padding: 8px; font-weight: bold;\"\u003eProbe Tip Material\u003c\/td\u003e\n      \u003ctd style=\"padding: 8px;\"\u003ePolyphenylene sulfide (PPS)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd style=\"padding: 8px; font-weight: bold;\"\u003eProbe Case Material\u003c\/td\u003e\n      \u003ctd style=\"padding: 8px;\"\u003eAISI 303 stainless steel\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd style=\"padding: 8px; font-weight: bold;\"\u003eTensile Strength\u003c\/td\u003e\n      \u003ctd style=\"padding: 8px;\"\u003e330 N (75 lbf) maximum probe-to-cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd style=\"padding: 8px; font-weight: bold;\"\u003eRecommended Torque\u003c\/td\u003e\n      \u003ctd style=\"padding: 8px;\"\u003e15 N-m (110 in-lb) maximum\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd style=\"padding: 8px; font-weight: bold;\"\u003eThread Engagement\u003c\/td\u003e\n      \u003ctd style=\"padding: 8px;\"\u003e15 mm maximum recommended\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd style=\"padding: 8px; font-weight: bold;\"\u003eDimensions\u003c\/td\u003e\n      \u003ctd style=\"padding: 8px;\"\u003e185 mm x 185 mm x 45 mm (H x W x D)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd style=\"padding: 8px; font-weight: bold;\"\u003eWeight\u003c\/td\u003e\n      \u003ctd style=\"padding: 8px;\"\u003e0.21 kg\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eThread Engagement:\u003c\/strong\u003e Do not exceed 15 mm of thread engagement inside the bracket or machine housing to prevent mechanical binding of the M10 x 1 casing.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eBend Radius:\u003c\/strong\u003e Maintain a minimum bend radius of 25 mm (1.0 inch) for the armored cable to avoid damage to the coaxial core and steel armor.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eConnector Care:\u003c\/strong\u003e Clean connection surfaces with a dry, lint-free cloth before joining ClickLoc connectors. Tighten only to finger-tight pressure.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eGap Calibration:\u003c\/strong\u003e Establish the static operating gap within the linear range of the transducer system (typically 2.0 mm or 80 mils) using a voltmeter.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eGrounding:\u003c\/strong\u003e Connect the outer shield of the extension cable to the designated instrument ground terminal at the Proximitor sensor housing. Do not ground the probe tip or casing.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666529677675,"sku":"330104-07-14-05-01-00","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330104-07-14-05-01-00-3300-xl-8-mm-proximity-probes-pokx4p0xh0x_9a6b64de-5c3c-4b96-bd8e-d09969d0d414.jpg?v=1765440337"},{"product_id":"bently-nevada-330901-10-24-10-02-00-3300-nsv-proximity-probes","title":"Bently Nevada 330901-10-24-10-02-00 3300 NSv Proximity Probes","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\n\u003cp\u003eA partially unthreaded 1\/4-28 UNF steel probe body with 1.0 inch of unthreaded length (Option 10), a 2.4-inch overall case length (Option 24), and a 1.0-meter standard cable (Option 10) defines this 3300 XL NSv proximity transducer configuration — \u003cstrong\u003e330901-10-24-10-02-00\u003c\/strong\u003e.\u003c\/p\u003e\n\u003cp\u003eThis specific configuration does not include a stainless steel armor jacket or connector protector (Option 02) and is designed for applications where hazardous area approvals are not required (Option 00). In contrast to armored configurations such as the 330902 series or configurations featuring FluidLoc cable technology (Option 11 or 12), this unarmored standard-cable model provides a lightweight, highly flexible solution for tight installation spaces with reduced target area geometry.\u003c\/p\u003e\n\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e1\/4-28 UNF Thread Configuration:\u003c\/strong\u003e Manufactured with standard threads and no protective armor (330901 series).\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e1.0 Inch Unthreaded Length (Option 10):\u003c\/strong\u003e Matches specified mounting requirements where a portion of the probe body must remain unthreaded.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e2.4-Inch Case Length (Option 24):\u003c\/strong\u003e Designed for standard deep-port insertion installations.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e1.0-Meter Total Length (Option 10):\u003c\/strong\u003e Provides 1.0 meter (39 inches) of integrated coaxial cable to connect directly to a 330930 extension cable or compatible 330980 Proximitor sensor.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eClickLoc Miniature Coaxial Connector (Option 02):\u003c\/strong\u003e Standard ClickLoc male connector without connector protector on standard 75-ohm cable.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNo Agency Approvals Required (Option 00):\u003c\/strong\u003e Suitable for non-hazardous area environments.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cp\u003eThe 3300 NSv Proximity Transducer System is designed for machinery with small target diameters or limited mounting clearance, where standard 8 mm probes cannot be installed due to space constraints. Typical installations include:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eVibration and position measurements on small-bore rotating machinery\u003c\/li\u003e\n\u003cli\u003eRadial vibration and axial position sensing on aeroderivative gas turbines\u003c\/li\u003e\n\u003cli\u003eCentrifugal compressors and pumps with small shafts (under 30 mm)\u003c\/li\u003e\n\u003cli\u003eTurbine auxiliary systems and gearboxes\u003c\/li\u003e\n\u003cli\u003eFluid-film bearing monitoring in space-restricted environments\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003ctable border=\"1\" cellpadding=\"5\" cellspacing=\"0\"\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eOption \/ Segment\u003c\/th\u003e\n\u003cth\u003eCode on This SKU\u003c\/th\u003e\n\u003cth\u003eDescription \/ Configuration Meaning\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOrderable Part Number\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e330901-10-24-10-02-00\u003c\/td\u003e\n\u003ctd\u003e3300 NSv Proximity Probe, 1\/4-28 UNF thread, without armor\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eA - Unthreaded Length Option\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e10\u003c\/td\u003e\n\u003ctd\u003e1.0 in (25 mm) unthreaded length (ordered in 0.1-inch increments)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eB - Overall Case Length Option\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e24\u003c\/td\u003e\n\u003ctd\u003e2.4 in (61 mm) overall case length (ordered in 0.1-inch increments)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eC - Total Length Option\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e10\u003c\/td\u003e\n\u003ctd\u003e1.0 meter (39 inches) total cable length\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eD - Connector and Cable-Type Option\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e02\u003c\/td\u003e\n\u003ctd\u003eMiniature coaxial ClickLoc connector, standard cable (no connector protector)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eE - Agency Approval Option\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e00\u003c\/td\u003e\n\u003ctd\u003eNo approvals required\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable border=\"1\" cellpadding=\"5\" cellspacing=\"0\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eManufacturer\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eBently Nevada (Baker Hughes)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePart Number \/ SKU\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e330901-10-24-10-02-00\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eSystem Compatibility\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e3300 XL NSv Proximity Transducer System\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eProbe Thread Size\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e1\/4-28 UNF-2A, without armor\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eUnthreaded Length\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e1.0 in (25.4 mm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eCase Length\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e2.4 in (61.0 mm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eTotal Cable Length\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e1.0 meter (39 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eConnector Type\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eMiniature coaxial ClickLoc male connector (gold-plated brass)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eCable Jacket \/ Type\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e75-ohm coaxial standard cable, unarmored (2.8 mm max outside diameter)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eLinear Range\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e1.5 mm (60 mils); starts at 0.25 mm (10 mils) to 1.75 mm (70 mils)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eRecommended Gap Setting\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e1.0 mm (40 mils)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eIncremental Scale Factor (ISF)\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e7.87 V\/mm (200 mV\/mil) nominal\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eDeviation from Best Fit Straight Line (DSL)\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eLess than +\/-0.06 mm (+\/-2.3 mils)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eFrequency Response\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e0 to 10 kHz: +0, -3 dB typical (with up to 305 m \/ 1,000 ft of field wiring)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eProbe Tip Diameter\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e5.26 mm (0.207 in) maximum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eTarget Size Limit (Flat Target)\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eMinimum 8.9 mm (0.35 in) diameter; recommended minimum 13 mm (0.5 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eDC Resistance (Probe Center to Outer)\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e4.2 ohms +\/-0.5 ohms (for 1.0 m probe length)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eOperating Temperature Range\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e-52 degC to +177 degC (-62 degF to +351 degF)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eRelative Humidity Limit\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e100% condensing, non-submersible (tested to IEC 68-2-3 damp heat)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePressure Sealing Material\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eViton O-ring differential pressure seal between tip and case\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eMaximum Recommended Case Torque\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e5.1 N m (45 in lb)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eCable Minimum Bend Radius\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e25.4 mm (1.0 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\n\u003cp\u003eProper mechanical and electrical installation is critical to ensure accurate proximity probe measurements:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCase Torque Limit:\u003c\/strong\u003e When installing the 1\/4-28 UNF probe case, do not exceed the maximum recommended torque of 5.1 N m (45 in lb) to prevent thread or casing damage.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCable Bend Radius:\u003c\/strong\u003e Maintain a minimum coaxial cable bend radius of 25.4 mm (1.0 in) during cable routing.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThread Engagement:\u003c\/strong\u003e Ensure proper thread engagement limits (typical maximum thread engagement for a 1\/4-28 UNF probe is 0.375 inches) to prevent physical contact issues or binding.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnector Handling:\u003c\/strong\u003e ClickLoc connectors must be joined finger-tight. Ensure connectors are clean and dry before connection. Installing a connector protector or using silicone tape (not recommended in oil-exposed environments) is advised to prevent fluid ingress.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProbe Gapping:\u003c\/strong\u003e Set the initial probe gap to approximately 1.0 mm (40 mils) using a feeler gauge or by monitoring the Proximitor output voltage (typically -9.0 Vdc to -10.0 Vdc) for centering in the linear range.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eCompliance and Certifications\u003c\/h3\u003e\n\u003cp\u003eThis specific configuration (Option 00) is designated for applications where specialized hazardous area safety approvals are not required. For applications requiring intrinsic safety, non-incendive, or zone certifications (such as ATEX, IECEx, or CSA), specify the Option 05 (Multiple Approvals) configuration.\u003c\/p\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666529775979,"sku":"330901-10-24-10-02-00","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330901-10-24-10-02-00-3300-nsv-proximity-probes-y5yirl1fi3d_e557b226-ec98-45e8-af82-6882aa5ec3da.jpg?v=1765440339"},{"product_id":"bently-nevada-330101-30-60-90-02-00-3300-xl-8-mm-proximity-probe","title":"Bently Nevada 330101-30-60-90-02-00 3300 XL 8 mm Proximity Probe","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eBently Nevada 330101-30-60-90-02-00\u003c\/strong\u003e is an unarmored \u003cstrong\u003e8 mm proximity probe\u003c\/strong\u003e designed for non-contact shaft vibration and position measurement within critical rotating machinery. As a key component of the 3300 XL 8 mm Proximity Transducer System, this specific configuration features a 3\/8-24 UNF threaded case with a 3.0-inch unthreaded length, a 6.0-inch overall case length, a 9.0-meter total cable length, and a miniature coaxial ClickLoc connector, configured without agency approvals.\u003c\/p\u003e\n\u003cp\u003eOperating on the eddy-current principle, this transducer system measures the dynamic and static distance between the probe tip and the observed conductive target, such as a machine shaft. It pairs seamlessly with 3300 XL Proximitor sensors (such as the 330180 series) and standard extension cables to deliver extremely accurate, temperature-stable displacement signals. This configuration is commonly integrated into machinery protection systems (including the Bently Nevada 3500 series) to monitor fluid-film bearing clearance, radial shaft vibration, and axial thrust position in high-speed industrial applications.\u003c\/p\u003e\n\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eEddy-current sensor design for precise non-contact measurement of shaft displacement and vibration.\u003c\/li\u003e\n  \u003cli\u003eGenerous 9.0-meter total length enables direct connection to a Proximitor sensor without requiring a separate extension cable, simplifying wiring in specific system layouts.\u003c\/li\u003e\n  \u003cli\u003e3.0-inch unthreaded length allows deep insertion into machine casing or bearing housings while leaving a 3.0-inch threaded section for robust mechanical adjustment and locking.\u003c\/li\u003e\n  \u003cli\u003eStandard unarmored cable design provides a lightweight, flexible routing path suitable for installations with protective conduit.\u003c\/li\u003e\n  \u003cli\u003eMiniature coaxial ClickLoc connector offers a secure, reliable electrical connection that resists moisture and vibration.\u003c\/li\u003e\n  \u003cli\u003eRobust probe tip constructed from high-durability PPS material to withstand harsh, oil-rich industrial environments.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cp\u003eThis proximity probe is ideal for machinery protection and condition monitoring in heavy-industry sectors such as oil and gas, petrochemicals, power generation, and water treatment. Typical application scenarios include:\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eRadial shaft vibration monitoring in steam and gas turbines.\u003c\/li\u003e\n  \u003cli\u003eThrust (axial) position measurements on high-speed compressors and turbochargers.\u003c\/li\u003e\n  \u003cli\u003eRotor displacement and bearing wear tracking in heavy industrial pumps and gearboxes.\u003c\/li\u003e\n  \u003cli\u003eShaft centerline tracking and rotational speed\/keyphaser references.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eOption \/ Segment\u003c\/th\u003e\n      \u003cth\u003eCode on This SKU\u003c\/th\u003e\n      \u003cth\u003eDescription \/ Meaning\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOrderable Part Number\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e\u003cstrong\u003e330101-30-60-90-02-00\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e3300 XL 8 mm Proximity Probe, 3\/8-24 UNF thread, without armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eA - Unthreaded Length Option\u003c\/td\u003e\n      \u003ctd\u003e30\u003c\/td\u003e\n      \u003ctd\u003e3.0 inches (76 mm) unthreaded length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eB - Overall Case Length Option\u003c\/td\u003e\n      \u003ctd\u003e60\u003c\/td\u003e\n      \u003ctd\u003e6.0 inches (152 mm) overall case length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eC - Total Length Option\u003c\/td\u003e\n      \u003ctd\u003e90\u003c\/td\u003e\n      \u003ctd\u003e9.0 meters (29.5 feet) total length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eD - Connector and Cable-Type Option\u003c\/td\u003e\n      \u003ctd\u003e02\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector, standard cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eE - Agency Approval Option\u003c\/td\u003e\n      \u003ctd\u003e00\u003c\/td\u003e\n      \u003ctd\u003eNo agency approvals required\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eManufacturer\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eBently Nevada\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eModel \/ Part Number\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330101-30-60-90-02-00\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProduct Series\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e3300 XL Transducer System\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Diameter\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e8 mm\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eMeasurement Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eNon-contact displacement (proximity)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOperating Principle\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eEddy current\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eThread Size\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e3\/8-24 UNF\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eMechanical Protection\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eWithout armor (unarmored cable)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eUnthreaded Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e3.0 in (76 mm)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOverall Case Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e6.0 in (152 mm)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eTotal Probe Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e9.0 meters (29.5 feet)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eConnector Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eWeight\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e0.14 kg\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eDimensions\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e45 mm x 95 mm x 95 mm (H x W x D)\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProbe Gapping:\u003c\/strong\u003e Mount the probe with the appropriate physical gap from the target surface (typically 1.27 mm or 50 mils for standard calibration, corresponding to -10 VDC output) before locking it into position.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCable Routing:\u003c\/strong\u003e Avoid sharp bends when routing the unarmored cable. Ensure the cable is supported and run through dedicated protective conduit if exposed to physical hazard or extreme mechanical wear.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eGrounding \u0026amp; Shielding:\u003c\/strong\u003e Connect the outer shield of the probe cable to the instrument ground inside the Proximitor sensor housing. Avoid multiple ground points to prevent ground loops.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eMechanical Clearance:\u003c\/strong\u003e Maintain a minimum radial clearance around the probe tip of at least 3 probe diameters (approximately 24 mm) from any surrounding metal to avoid eddy-current side-loading effects.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLocking:\u003c\/strong\u003e Tighten mounting nuts securely to the machinery housing or bracket to prevent drift due to structural vibration. Do not exceed recommended torque limits for 3\/8-24 UNF threads.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666529874283,"sku":"330101-30-60-90-02-00","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330101-30-60-90-02-00-3300-xl-8-mm-probe-4nqjqeh1yhc_ac158f1d-1974-4167-af6a-026c57745cea.jpg?v=1765440343"},{"product_id":"bently-nevada-330901-10-20-10-02-05-3300-nsv-proximity-probe","title":"Bently Nevada 330901-10-20-10-02-05 3300 NSv Proximity Probe","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\n\u003cp\u003eUnarmored 1\/4-28 UNF threaded probe body with 1.0 in unthreaded length (Option 10), 2.0 in overall case length (Option 20), and a 1.0 m total standard cable length (Option 10) specifies this 3300 NSv proximity probe configuration — \u003cstrong\u003e330901-10-20-10-02-05 3300 NSv Proximity Probe\u003c\/strong\u003e.\u003c\/p\u003e\n\u003cp\u003eThis non-contacting eddy-current transducer is engineered for reduced target area and tight clearance environments, offering critical shaft vibration and position measurements on small-bore rotating machinery. Option 02 provides a miniature coaxial ClickLoc connector with standard cable, and Option 05 equips the assembly with Multiple Approvals for hazardous area installations.\u003c\/p\u003e\n\u003cp\u003eDesigned to operate seamlessly within the 3300 XL NSv Proximity Transducer System, this probe pairs directly with the 330930 NSv extension cable and the 330980 NSv Proximitor Sensor. Compared to standard 8 mm probe variants, the NSv design is optimized for applications with limited shaft geometry or close spacing requirements, utilizing its small tip size to prevent cross-talk and maintain measurement linear range up to 1.5 mm (60 mils).\u003c\/p\u003e\n\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eOption 10 unthreaded length provides a 1.0 in (25.4 mm) unthreaded section for specific installation depth requirements.\u003c\/li\u003e\n\u003cli\u003eOption 20 overall case length provides a 2.0 in (50.8 mm) total case length with 1\/4-28 UNF thread.\u003c\/li\u003e\n\u003cli\u003eOption 10 total length designates a 1.0 m (39 in) probe cable with a miniature coaxial ClickLoc connector.\u003c\/li\u003e\n\u003cli\u003eOption 02 connector type features a miniature male ClickLoc coaxial connector on standard unarmored coaxial cable.\u003c\/li\u003e\n\u003cli\u003eOption 05 multiple approvals deliver CSA, ATEX, and IECEx hazardous area certifications for intrinsically safe and non-sparking zones.\u003c\/li\u003e\n\u003cli\u003eUnarmored AISI 304 stainless steel case material stands up to demanding industrial environments.\u003c\/li\u003e\n\u003cli\u003ePolyphenylene sulfide (PPS) probe tip ensures robust chemical resistance and high-temperature performance.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eSmall-bore rotating machinery shaft monitoring\u003c\/li\u003e\n\u003cli\u003eShaft vibration and axial position measurements on aeroderivative gas turbines\u003c\/li\u003e\n\u003cli\u003eHigh-speed equipment with restricted target areas or limited radial clearances\u003c\/li\u003e\n\u003cli\u003eRadial vibration or position measurements where close sensor spacing is necessary\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eOption Segment\u003c\/th\u003e\n\u003cth\u003eCode Value\u003c\/th\u003e\n\u003cth\u003eDescription \/ Specification\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrderable Part Number\u003c\/td\u003e\n\u003ctd\u003e\u003cstrong\u003e330901-10-20-10-02-05\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e3300 NSv Proximity Probe, 1\/4-28 UNF thread, standard mount, without armor\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eA - Unthreaded Length Option\u003c\/td\u003e\n\u003ctd\u003e10\u003c\/td\u003e\n\u003ctd\u003e1.0 in (25.4 mm) unthreaded length\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eB - Overall Case Length Option\u003c\/td\u003e\n\u003ctd\u003e20\u003c\/td\u003e\n\u003ctd\u003e2.0 in (50.8 mm) overall case length\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eC - Total Length Option\u003c\/td\u003e\n\u003ctd\u003e10\u003c\/td\u003e\n\u003ctd\u003e1.0 meter (39 in) total cable length\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eD - Connector and Cable Option\u003c\/td\u003e\n\u003ctd\u003e02\u003c\/td\u003e\n\u003ctd\u003eMiniature coaxial ClickLoc connector, standard cable\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eE - Agency Approval Option\u003c\/td\u003e\n\u003ctd\u003e05\u003c\/td\u003e\n\u003ctd\u003eMultiple Approvals (CSA, ATEX, IECEx)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eManufacturer\u003c\/td\u003e\n\u003ctd\u003eBently Nevada (Baker Hughes)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePart Number\u003c\/td\u003e\n\u003ctd\u003e330901-10-20-10-02-05\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSystem Compatibility\u003c\/td\u003e\n\u003ctd\u003e3300 XL NSv Transducer System (330930 cable, 330980 Proximitor)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTip Diameter\u003c\/td\u003e\n\u003ctd\u003e5.26 mm (0.207 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eProbe Thread Size\u003c\/td\u003e\n\u003ctd\u003e1\/4-28 UNF-2A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eArmor Option\u003c\/td\u003e\n\u003ctd\u003eWithout stainless steel armor\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eLinear Range\u003c\/td\u003e\n\u003ctd\u003e1.5 mm (60 mils)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAverage Scale Factor (ASF)\u003c\/td\u003e\n\u003ctd\u003e7.87 V\/mm (200 mV\/mil)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temperature Range\u003c\/td\u003e\n\u003ctd\u003e-52 degC to +177 degC (-62 degF to +351 degF)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCase Material\u003c\/td\u003e\n\u003ctd\u003eAISI 304 stainless steel (SST)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTip Material\u003c\/td\u003e\n\u003ctd\u003ePolyphenylene sulfide (PPS)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCable Type\u003c\/td\u003e\n\u003ctd\u003e75 ohm coaxial, FEP insulated, standard cable\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eConnector Type\u003c\/td\u003e\n\u003ctd\u003eMiniature male coaxial ClickLoc connector\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTensile Strength\u003c\/td\u003e\n\u003ctd\u003e220 N (50 lb) maximum rated probe case to probe lead\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eConnections and Interfaces\u003c\/h3\u003e\n\u003cp\u003eThe probe lead terminates in a miniature male coaxial ClickLoc connector, designed for quick, secure connection to the 330930 extension cable without requiring specialized assembly tools.\u003c\/p\u003e\n\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eEnsure a minimum probe tip clearance of at least 25 mm (1.0 in) for axial position measurements to prevent electromagnetic cross-talk with adjacent sensors.\u003c\/li\u003e\n\u003cli\u003eFor radial vibration measurements on shafts smaller than 20 mm (0.8 in), expect a potential scale factor change up to 10%.\u003c\/li\u003e\n\u003cli\u003eRecommended case torque must not exceed 5.1 N m (45 in lb) during installation into a 1\/4-28 UNF threaded hole.\u003c\/li\u003e\n\u003cli\u003eProtect coaxial connectors using self-fusing silicone tape or a connector protector kit to prevent liquid ingress.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eCompliance and Certifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eCSA: Class I, Zone 0: AEx\/Ex ia IIC T5...T1 Ga; Class I, Div 1, Groups A, B, C, D\u003c\/li\u003e\n\u003cli\u003eATEX\/IECEx: Ex ia IIC T5...T1 Ga; Ex ia IIIC T90C...T280C Dc; Ex nA IIC T5...T1 Gc; Ex ec IIC T5...T1 Gc\u003c\/li\u003e\n\u003cli\u003eRoHS: Compliant with European Community Directive 2011\/65\/EU and China RoHS (15-year EFUP)\u003c\/li\u003e\n\u003cli\u003eFunctional Safety: SIL 2 certified (HFT=0), SIL 3 capable (HFT=1)\u003c\/li\u003e\n\u003cli\u003eCE: Compliant with European Community Directive EMC 2014\/30\/EU\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666530365803,"sku":"330901-10-20-10-02-05","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330901-10-20-10-02-05-probe-15b533j5duq_56cc3038-2157-40dc-8a5a-bc3b23f6a8b8.jpg?v=1765440349"},{"product_id":"bently-nevada-330101-00-28-10-02-00-3300-xl-8-mm-proximity-probe","title":"Bently Nevada 330101-00-28-10-02-00 3300 XL 8 mm Proximity Probe","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eBently Nevada 330101-00-28-10-02-00\u003c\/strong\u003e is an unarmored 8 mm \u003cstrong\u003eproximity probe\u003c\/strong\u003e configured with a fully threaded 3\/8-24 UNF housing (0.0 inches unthreaded length), a 2.8-inch case length, and a 1.0-meter (3.3 feet) standard coaxial cable with a miniature ClickLoc connector. Designed for systems that do not require hazardous area approvals, this specific variant provides non-contact vibration and shaft position measurements in industrial machinery. It acts as a critical sensing element within a 3300 XL monitoring chain, pairing seamlessly with a 330180 series Proximitor sensor and a corresponding standard extension cable to deliver highly accurate displacement readings.\u003c\/p\u003e\n\u003cp\u003eThis proximity probe utilizes eddy-current technology to track dynamic displacement, such as radial shaft vibration and axial thrust position. Since it is constructed without protective armor, this variant is ideal for installations where the cable path is adequately protected inside conduits or dry machine casings. Its 1.0-meter cable must be integrated into a 5-meter or 9-meter overall system configuration to maintain precise calibration and minimize interference.\u003c\/p\u003e\n\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e8 mm tip diameter proximity probe designed for non-contact eddy-current displacement measurement.\u003c\/li\u003e\n  \u003cli\u003eFully threaded 2.8-inch case length without protective armor, optimal for installations where external mechanical wear is not a primary risk.\u003c\/li\u003e\n  \u003cli\u003eEquipped with a miniature coaxial ClickLoc connector, ensuring a secure, click-verified snap connection.\u003c\/li\u003e\n  \u003cli\u003eStandard cable design suited for typical industrial environments with oil and moisture exposure.\u003c\/li\u003e\n  \u003cli\u003eRobust stainless steel case construction with high-performance PPS tip material.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cp\u003eTypical applications for this probe include turbine shaft vibration and position monitoring, critical compressor and pump rotor displacement measurements, and general rotating machinery protection within power generation, oil and gas, and chemical processing facilities.\u003c\/p\u003e\n\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eOption Segment\u003c\/th\u003e\n      \u003cth\u003eCode\u003c\/th\u003e\n      \u003cth\u003eDescription\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOrderable Part Number\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330101-00-28-10-02-00\u003c\/td\u003e\n      \u003ctd\u003e3300 XL 8 mm Proximity Probe, 3\/8-24 UNF thread, without armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eA - Unthreaded Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e00\u003c\/td\u003e\n      \u003ctd\u003e0.0 in (0 mm) unthreaded length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eB - Overall Case Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e28\u003c\/td\u003e\n      \u003ctd\u003e2.8 in (71 mm) case length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eC - Total Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e10\u003c\/td\u003e\n      \u003ctd\u003e1.0 meter (3.3 feet) total length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eD - Connector and Cable-Type Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e02\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector, standard cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eE - Agency Approval Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e00\u003c\/td\u003e\n      \u003ctd\u003eNot required\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eManufacturer\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eBently Nevada\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003ePart Number\/Model\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330101-00-28-10-02-00\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProduct Family\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e3300 XL 8 mm Proximity Transducer System\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Diameter\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e8 mm\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOperating Principle\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eEddy current\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eMeasurement Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eDisplacement (proximity)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eLinear Range\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e2.0 mm (80 mils), starting at 0.25 mm (10 mils) from target\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eIncremental Scale Factor (ISF)\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e7.87 V\/mm (200 mV\/mil) nominal\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe DC Resistance\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e7.59 ohms +\/- 0.50 ohms (from center conductor to outer conductor)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOperating Temperature\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e-52 degC to +177 degC (-62 degF to +350 degF)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eDimensions\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e45 mm x 95 mm x 95 mm (H x W x D)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eWeight\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e0.14 kg\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\n\u003cp\u003eTo ensure proper operation of the proximity probe, verify that it is mounted with the correct probe gap (typically adjusted to -9 Vdc or approximately 1.27 mm \/ 50 mils) according to system calibration. Route the probe cable with proper shielding and grounding practices to eliminate noise coupling. Ensure that the thread engagement limits are respected during installation, and finger-tighten the ClickLoc connectors to prevent damage to the gold-plated contacts.\u003c\/p\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666530398571,"sku":"330101-00-28-10-02-00","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330101-00-28-10-02-00-3300-xl-8-mm-probe-tga2eq5xtjp_44b8f8d2-642a-4d92-870f-cd6430aef76d.jpg?v=1765440351"},{"product_id":"bently-nevada-330101-00-75-20-02-00-3300-xl-8-mm-proximity-probe","title":"Bently Nevada 330101-00-75-20-02-00 3300 XL 8 mm Proximity Probe","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eBently Nevada 330101-00-75-20-02-00\u003c\/strong\u003e is a highly precise and robust \u003cstrong\u003e3300 XL 8 mm proximity probe\u003c\/strong\u003e configured with a fully threaded 7.5-inch case, a 2.0-meter total length standard cable, and no unthreaded offset (0.0 in). This unarmored eddy-current sensor is engineered specifically for non-contact machinery protection and condition monitoring, delivering high-resolution displacement measurements in critical industrial rotating equipment. Designed without any unthreaded portion, this variant allows complete thread support through bearing housings or specialized mounting fixtures where case protrusion must be avoided. The standard cable configuration coupled with a ClickLoc miniature coaxial connector provides a stable, electrically quiet connection to extension cables, making it excellent for general-purpose monitoring networks that do not require specialized steel armor or hazardous area agency certification.\u003c\/p\u003e\n\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eFully Threaded Design:\u003c\/strong\u003e The 7.5-inch overall case is entirely threaded (0.0 in unthreaded length) to offer optimal depth adjustability and structural stability.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eStandard Coaxial Cable:\u003c\/strong\u003e Includes a 2.0-meter (6.6 feet) flexible coaxial cable without external armoring, designed for clean pathways or conduit routing.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eClickLoc Connector Technology:\u003c\/strong\u003e Terminated with a high-durability miniature coaxial ClickLoc connector for a secure and corrosion-resistant coupling.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eNon-Contact Displacement Sensing:\u003c\/strong\u003e Utilizing the eddy-current operating principle, it provides continuous, dynamic measurements of rotor shaft vibration and axial position.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eRobust Construction:\u003c\/strong\u003e A polyphenylene sulfide (PPS) tip and stainless steel probe body withstand harsh chemical and oil-film industrial environments.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eSteam turbine rotor shaft vibration and position tracking\u003c\/li\u003e\n  \u003cli\u003eCentrifugal compressor thrust bearing position monitoring\u003c\/li\u003e\n  \u003cli\u003eBoiler feed pump shaft displacement and thrust displacement\u003c\/li\u003e\n  \u003cli\u003eGeneral-purpose rotating machinery vibration protection loops\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eOption Segment\u003c\/th\u003e\n      \u003cth\u003eCode Value\u003c\/th\u003e\n      \u003cth\u003eDescription \/ Meaning\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOrderable Part Number\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330101-00-75-20-02-00\u003c\/td\u003e\n      \u003ctd\u003e3300 XL 8 mm Proximity Probe, 3\/8-24 UNF thread, without armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eA - Unthreaded Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e00\u003c\/td\u003e\n      \u003ctd\u003e0.0 in (No unthreaded portion, fully threaded)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eB - Overall Case Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e75\u003c\/td\u003e\n      \u003ctd\u003e7.5 in (7.5-inch total threaded case length)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eC - Total Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e20\u003c\/td\u003e\n      \u003ctd\u003e2.0 meters (6.6 feet) overall length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eD - Connector and Cable-Type Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e02\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector, standard cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eE - Agency Approval Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e00\u003c\/td\u003e\n      \u003ctd\u003eNot required (No hazardous area approvals)\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eManufacturer\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eBently Nevada (Baker Hughes)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003ePart Number \/ Model\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330101-00-75-20-02-00\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProduct Series\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e3300 XL 8 mm Proximity Transducer System\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eProbe Diameter\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e8 mm\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eThread Specification\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e3\/8-24 UNF-2A (without armor)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eUnthreaded Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e0.0 in (0.0 mm)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOverall Case Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e7.5 in (190.5 mm)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eTotal Probe Length\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e2.0 meters (6.6 feet)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eConnector Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eCable Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eStandard coaxial cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eOperating Principle\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eEddy current non-contact measurement\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eMeasurement Type\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003eRadial vibration, axial position, speed, and phase reference\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eDimensions (H x W x D)\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e45 mm x 95 mm x 95 mm (H x W x D)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eWeight\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e0.14 kg\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eAdjusting Probe Gap:\u003c\/strong\u003e Calculate and lock the physical gap positioning using standard calibration voltage responses before securing locknuts.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCable Isolation:\u003c\/strong\u003e Route standard unarmored cables through dedicated electrical conduits or protective trays to safeguard them from mechanical wear or impact.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eShield Grounding:\u003c\/strong\u003e Maintain proper noise immunity by keeping the coaxial cable shield continuous and grounding it at a single point, typically at the Proximitor sensor housing.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eMinimizing Crosstalk:\u003c\/strong\u003e Ensure the probe maintains adequate clearance from neighboring metallic surfaces to prevent side-view eddy-current distortions.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666530529643,"sku":"330101-00-75-20-02-00","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330101-00-75-20-02-00-3300-xl-8-mm-proximity-probes-x1ffknjbwsv_dddec6d3-5427-4f3e-a1ec-d2f903523491.jpg?v=1765440353"},{"product_id":"bently-nevada-330101-00-24-10-02-00-3300-xl-8-mm-proximity-probe","title":"Bently Nevada 330101-00-24-10-02-00 3300 XL 8 mm Proximity Probe","description":"\u003ch3\u003eDescription\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eBently Nevada 330101-00-24-10-02-00\u003c\/strong\u003e is an 8 mm proximity probe that is a core component of the \u003cstrong\u003e3300 XL 8 mm Proximity Transducer System\u003c\/strong\u003e. Operating on the eddy-current principle, this probe provides high-precision, non-contact measurement of shaft vibration and dynamic position in critical rotating machinery. Unlike armored configurations, this specific variant features a flexible, unarmored standard coaxial cable. It is configured with a fully threaded 2.4-inch case (0.0 inches of unthreaded length) and a 3\/8-24 UNF thread, allowing for versatile depth adjustments within standard bearing housings. Equipped with a standard 1.0-meter (3.3 feet) cable and terminated with a miniature gold ClickLoc coaxial connector, this configuration is optimized for standard applications where connector protectors and hazardous area agency approvals are not required. It integrates directly with 330180 series Proximitor sensors and standard extension cables to transmit clean, low-noise displacement data to machine protection systems such as the Bently Nevada 3500 rack.\u003c\/p\u003e\n\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eNon-contact eddy-current technology prevents physical wear and maintains long-term calibration stability.\u003c\/li\u003e\n  \u003cli\u003eFully threaded 3\/8-24 UNF stainless steel case provides robust mechanical support and flexible depth adjustments.\u003c\/li\u003e\n  \u003cli\u003ePolyphenylene sulfide (PPS) probe tip offers superior resistance to chemical attack, industrial oils, and humidity.\u003c\/li\u003e\n  \u003cli\u003eMiniature ClickLoc coaxial connector delivers a secure, positive-lock connection with low signal impedance.\u003c\/li\u003e\n  \u003cli\u003eUnarmored standard coaxial cable ensures optimal flexibility for routing through standard protective conduits.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cp\u003eThe 330101-00-24-10-02-00 proximity probe is designed for heavy-duty industrial machinery protection, particularly in power generation and petrochemical sectors. Primary applications include:\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eRadial shaft vibration monitoring on high-speed steam and gas turbines.\u003c\/li\u003e\n  \u003cli\u003eAxial shaft position and thrust bearing wear measurement on compressors and expanders.\u003c\/li\u003e\n  \u003cli\u003eRotor dynamic displacement monitoring in critical industrial pumps.\u003c\/li\u003e\n  \u003cli\u003eContinuous condition monitoring of rotating elements to prevent catastrophic mechanical failure.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eOrdering Information\u003c\/h3\u003e\n\u003cp\u003eThe specific configuration of this proximity probe is defined by its multi-segment orderable code, detailed in the table below:\u003c\/p\u003e\n\u003ctable\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eOption Segment\u003c\/th\u003e\n      \u003cth\u003eCode on This SKU\u003c\/th\u003e\n      \u003cth\u003eMeaning from Official Datasheet\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eBase Model\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e330101\u003c\/td\u003e\n      \u003ctd\u003e3300 XL 8 mm Proximity Probe, 3\/8-24 UNF thread, without armor\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eA - Unthreaded Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e00\u003c\/td\u003e\n      \u003ctd\u003e0.0 inches (fully threaded case)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eB - Overall Case Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e24\u003c\/td\u003e\n      \u003ctd\u003e2.4 inches overall case length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eC - Total Length Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e10\u003c\/td\u003e\n      \u003ctd\u003e1.0 meter (3.3 feet) total cable length\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eD - Connector\/Cable Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e02\u003c\/td\u003e\n      \u003ctd\u003eMiniature coaxial ClickLoc connector, standard cable\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003e\u003cstrong\u003eE - Agency Approval Option\u003c\/strong\u003e\u003c\/td\u003e\n      \u003ctd\u003e00\u003c\/td\u003e\n      \u003ctd\u003eNo hazardous area approvals required\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eTechnical Specifications\u003c\/h3\u003e\n\u003ctable\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eParameter\u003c\/th\u003e\n      \u003cth\u003eValue \/ Specification\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eManufacturer\u003c\/td\u003e\n      \u003ctd\u003eBently Nevada\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003ePart Number \/ Model\u003c\/td\u003e\n      \u003ctd\u003e330101-00-24-10-02-00\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eProduct System\u003c\/td\u003e\n      \u003ctd\u003e3300 XL 8 mm Proximity Transducer System\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eMeasurement Type\u003c\/td\u003e\n      \u003ctd\u003eDisplacement (proximity)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eOperating Principle\u003c\/td\u003e\n      \u003ctd\u003eEddy current\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eProbe Tip Diameter\u003c\/td\u003e\n      \u003ctd\u003e8 mm\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eThread Pitch \/ Size\u003c\/td\u003e\n      \u003ctd\u003e3\/8-24 UNF\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eLinear Range\u003c\/td\u003e\n      \u003ctd\u003e2.0 mm (80 mils), beginning 0.25 mm (10 mils) from the target\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eIncremental Scale Factor (ISF)\u003c\/td\u003e\n      \u003ctd\u003e7.87 V\/mm (200 mV\/mil) nominal\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eRecommended Gap Setting\u003c\/td\u003e\n      \u003ctd\u003e-9 Vdc (approximately 1.27 mm or 50 mils)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eOperating Temperature\u003c\/td\u003e\n      \u003ctd\u003e-52 degC to +177 degC (-62 degF to +350 degF)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eProbe Tip Material\u003c\/td\u003e\n      \u003ctd\u003ePolyphenylene sulfide (PPS)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eCase Material\u003c\/td\u003e\n      \u003ctd\u003eAISI 303 or 304 stainless steel\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eConnector Material\u003c\/td\u003e\n      \u003ctd\u003eGold-plated brass\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eDimensions\u003c\/td\u003e\n      \u003ctd\u003e45 mm x 95 mm x 95 mm (H x W x D)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eWeight\u003c\/td\u003e\n      \u003ctd\u003e0.14 kg\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eInstallation Guidelines\u003c\/h3\u003e\n\u003cp\u003eTo secure reliable operation and accurate measurements, technical engineers must observe the following installation protocols:\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCalibration Gap:\u003c\/strong\u003e Adjust the probe to a physical gap of approximately 1.27 mm (50 mils) from the target material, corresponding to an electrical output of -9 Vdc, placing it at the midpoint of the linear range.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCable Isolation:\u003c\/strong\u003e Coaxial cables must be routed in isolated, grounded conduits or cable trays, keeping them separate from high-current power cables to prevent electromagnetic noise induction.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eConnector Hand-Tightening:\u003c\/strong\u003e Gold ClickLoc connectors should be joined finger-tight. Avoid using heavy pliers, as excessive torque can damage the internal gold contacts or strip threads.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eThread Engagement Limits:\u003c\/strong\u003e For standard 3\/8-24 UNF external threads, limit maximum internal thread engagement to 0.563 inches to avoid mechanical binding during installation.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":52666530562411,"sku":"330101-00-24-10-02-00","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0953\/3227\/0443\/files\/bently-nevada-330101-00-24-10-02-00-proximity-probes-sdl1t3oyofa_95f198c0-1bca-47cd-b7d4-5e9887166938.jpg?v=1765440355"}],"url":"https:\/\/www.plcprotech.com\/vi\/collections\/proximity-probes-and-cables.oembed","provider":"PLC ProTech Ltd.","version":"1.0","type":"link"}