Manufacturer: Omron
Product No.: CJ1W-EIP21
Country of origin:Япония
Product Type: PLC Communication Modules
Payment: T/T, Western Union
Weight: 1500g
Dimensions: 90 mm x 31 mm x 65 mm
Shipping port: Xiamen
Warranty: 12 months
Facilitating high-speed industrial Ethernet communications within modular control architectures, the Omron CJ1W-EIP21 functions as a CPU Bus Unit designed to interface PLC controllers directly with industrial EtherNet/IP networks. This unit enables both high-speed tag data links (implicit messaging) for real-time I/O control and message communications (explicit messaging) for explicit data exchange. Integrating seamlessly onto either local CPU racks or expansion racks, it bridges logical plant-floor control layers with supervisory SCADA, MES, or enterprise database environments without requiring dedicated external gateways.
| Manufacturer | Omron Industrial Automation |
| Model Number | CJ1W-EIP21 |
| Unit Classification | CJ-series CPU Bus Unit |
| Supported Platforms | NJ-series, CJ-series, CP1H-series PLCs |
| Physical Mounting Locations | CPU Rack, Expansion Rack |
| Maximum Units per System | NJ System: 4 max | CJ/NSJ System: 8 max | CP1H System: 2 max |
| Media Access Control (MAC) | CSMA/CD |
| Modulation Method | Baseband |
| Transmission Topology | Star formation (via switching hubs) |
| Baud Rate | 100 Mbit/s (100Base-TX) |
| Maximum Segment Distance | 100 meters (node to network switch/hub) |
| Internal Current Consumption | 410 mA maximum at 5 V DC |
| Dimensions (H x W x D) | 90 mm x 31 mm x 65 mm |
| Unit Weight | 0.094 kg (94 g) |
| Shipping Weight (Calculated) | 1.5 kg |
| Interface Component | Description / Pin Assignment |
|---|---|
| RJ45 Connector | Standard 8-pin modular connector for 100Base-TX Ethernet cable (Category 5/5e shielded twisted pair recommended). |
| Rotary Switches | Two hex decimal rotary switches (x16 and x1) located on the front panel to configure the hardware node IP address suffix. |
| LED Indicators | RUN (Green), ERC (Red), ERH (Red), MS (Green/Red), NS (Green/Red), LNK/ACT (Yellow). |
Based on industrial commissioning logs, the configuration and management of the CJ1W-EIP21 require precise adherence to network bandwidth constraints and configuration rules.
The CJ1W-EIP21 can directly replace older CJ1W-ETN21 Ethernet modules in legacy network topographies, though configuration steps differ. When migrating to an NJ-series controller platform, the unit's maximum allowable instances drop from 8 units (CJ-series limit) to 4 units due to increased backplane bandwidth demands. Ensure the unit's firmware matches the Sysmac Studio or CX-Programmer library version to avoid catalog mismatch faults during upload.
A common real-world failure mode occurs when Tag Data Link (implicit messaging) connections saturate the unit's maximum packet processing rate (PPS). Keep track of your packet limits using the Network Configurator tool. If the cumulative packet-per-second limit is exceeded, cyclic communications may time out, throwing an 'ERH' (EtherNet/IP Unit Error) status. To alleviate this, adjust the Requested Packet Interval (RPI) configurations upward for non-critical monitoring nodes.
To minimize high-frequency electrostatic interference on plant-floor environments, you must use double-shielded STP Cat 5e (or better) cabling. Clamp the shield securely to the rack's functional ground bar. When utilizing the rotary switches on the front bezel to set the IP address, note that the default hardware setting reads the node address as part of the Class C IP scheme (e.g., 192.168.250.X). If custom routing or non-standard subnets are required, set the rotary switches to '00' to enable software-configured IP parameters via CX-Programmer.
Align the top hook of the CJ1W-EIP21 module into the mounting slot of the CJ/NJ-series backplane.
Pivot the unit downward until the bottom connector snaps securely into the bus socket on the backplane.
Tighten the upper and lower mounting screws to secure the chassis. Ensure they are tightened to the recommended torque of 0.4 N-m.
Insert the RJ45 Ethernet patch cord until the locking tab clicks cleanly into place. Ensure proper strain relief is applied to prevent physical pull on the port.
Глобална експресна доставка
Връщания и гаранция
Поръчките се обработват и доставят от понеделник до петък (с изключение на официалните празници).
За пълна информация относно допустимост, такси за презареждане и международни връщания, моля, разгледайте нашия официален Политика за възстановяване и връщане .
| Country of origin |
Япония
|
Тази статия обяснява как интегрираните електрически задвижвания, като серията e-Actuator на SMC, трансформират индустриалното управление на движението, като заменят традиционните пневматични и...
Тази статия обяснява как PLC системите изпълняват основни математически операции като събиране, изваждане, умножение, деление, модуло и степенуване в индустриалната автоматизация. Показва как тези...
Статията обяснява няколко усъвършенствани булеви логически функции, използвани в програмирането на PLC, извън основните операции AND, OR и NOT. Тя разглежда как инструменти като таблици на...
Булевата логика е основата на всяка програма за PLC. От прости машинни управления до сложни индустриални автоматизационни системи, логическите врати определят как контролерите реагират на променящите...
Индустриалните защитни стени играят ключова роля в киберсигурността на OT, като защитават мрежите PLC, DCS и SCADA чрез сегментация, контрол на входящия/изходящия трафик и интеграция на IDS/IPS в...
Съвременните роботизирани захвати се развиват отвъд традиционните механични челюсти. От системи с лепкави повърхности, вдъхновени от геконите, и меки захвати за хранителни продукти до инструменти за...
