Manufacturer: Bently Nevada
Product No.: 3500/25-01-01-CN
Country of origin:Stany Zjednoczone
Product Type: Vibration Monitoring Modules
Payment: T/T, Western Union
Weight: 320g
Shipping port: Xiamen
Warranty: 12 months
Providing high-accuracy phase reference and rotational speed measurements for machinery protection, the Bently Nevada 3500/25-01-01-CN is a half-height, dual-channel module designed for the 3500 Machinery Protection System. This specific model features a single half-height 2-channel Keyphasor card paired with an I/O module configured for internal terminations. The hardware processes input signals from proximity probes or magnetic pickups, converting them into digital phase reference pulses used by other monitoring modules in the rack. Approved under country-specific standards (CN designation), this industrial-grade module ensures reliable operation within critical diagnostic architectures.
| Option Code | Configuration Detail |
|---|---|
| 3500/25 | Enhanced Keyphasor Module |
| -01 | Single half-height 2-channel Keyphasor card (order for 2 channels) |
| -01 | I/O Module with Internal Terminations |
| -CN | Country Specific Approvals (China / Regional Standards) |
| Parameter | Value / Requirement |
|---|---|
| Manufacturer | Bently Nevada |
| Series | 3500 Machinery Protection System |
| Input Channels | 2 differential or single-ended channels |
| Input Signal Range | +0.8 V to -26.0 V (Non-contact sensors) or 8 V peak-to-peak (Magnetic pickups) |
| Input Impedance | 10 kohm minimum |
| Power Consumption | 3.2 Watts typical |
| Signal-to-Noise Ratio | Minimum 20 dB dynamic range |
| Operating Temperature Range | -30 degC to +65 degC (-22 degF to +149 degF) |
| Country of Origin | United States (Made in U.S.A.) |
| Shipping Weight (Calculated) | 2.0 kg (including module, internal terminations I/O card, and protective packaging) |
| Terminal / Pin No. | Signal Assignment | Description |
|---|---|---|
| 1 | KPH 1 + | Keyphasor Channel 1 Non-Inverting Signal Input |
| 2 | KPH 1 - | Keyphasor Channel 1 Inverting / Common Return |
| 3 | KPH 1 OUT | Transducer Power (-24 VDC Supply for Proximitor) |
| 4 | KPH 2 + | Keyphasor Channel 2 Non-Inverting Signal Input |
| 5 | KPH 2 - | Keyphasor Channel 2 Inverting / Common Return |
| 6 | KPH 2 OUT | Transducer Power (-24 VDC Supply for Proximitor) |
| 7 | SHIELD | Dedicated cable shield ground point (tied to chassis ground) |
The "Enhanced" 3500/25 module directly replaces legacy non-enhanced 3500/25 modules. However, firmware compatibility must be verified prior to hot-swapping: your 3500 Rack Configuration Software must be upgraded to version 3.3 or higher to configure the advanced dynamic hysteresis options. Do not attempt to run a non-enhanced card and an enhanced card as a redundant pair in the same slot space; both cards must share the same hardware revision level to guarantee system synchronization.
When configuring magnetic pickups, field engineers should note that the output signal drops significantly at low RPM. If the machine operates below 100 RPM, standard passive magnetic pickups may not generate sufficient amplitude to cross the threshold, leading to "Keyphasor Fault" indications. In these scenarios, use active proximity sensors which maintain constant voltage outputs down to zero speed.
To prevent electromagnetic interference (EMI) from neighboring power cables and variable frequency drives (VFDs), ensure Keyphasor wiring is routed via dedicated, shielded twisted-pair (STP) lines. The shield should only be grounded at the 3500 chassis ground terminal on the I/O card; the sensor-end shield must be left floating and insulated to eliminate parasitic ground loops.
Prior to removing or installing any 3500/25 module, ensure the rack is placed in a bypassed or safe state. Improper hot-swapping in active protection racks can trigger false machinery trip signals. Verify field wiring insulation to prevent accidental shorting of the -24 VDC transducer power lines to the chassis ground.
Inspect the module backplane and gold connector pins for debris or misalignment before insertion.
Align the half-height module card with the upper or lower guide rails in the selected slot location.
Slide the module gently but firmly straight back into the rack until the ejector tabs lock cleanly.
Secure the front-panel mounting screws to ensure proper chassis grounding and thermal contact.
Upload and verify configuration parameters via the Bently Nevada 3500 Rack Configuration software.
Globalna ekspresowa wysyłka
Zwroty i gwarancja
Zamówienia są przetwarzane i dostarczane od poniedziałku do piątku (z wyłączeniem dni świątecznych).
Aby poznać pełne warunki kwalifikowalności, opłaty za przyjęcie towaru z powrotem oraz szczegóły dotyczące zwrotów międzynarodowych, prosimy zapoznać się z naszym oficjalnym Polityka zwrotów i zwrotu pieniędzy .
| Country of origin |
Stany Zjednoczone
|
This article explains how integrated electric actuators, such as SMC’s e-Actuator series, are transforming industrial motion control by replacing traditional pneumatic and hydraulic systems. It...
This article explains how PLC systems perform core mathematical operations such as addition, subtraction, multiplication, division, modulo, and exponentiation within industrial automation. It shows...
The article explains several advanced Boolean logic functions used in PLC programming beyond basic AND, OR, and NOT operations. It covers how tools like truth tables, multiplexers, pulse generators,...
Boolean logic is the foundation of every PLC program. From simple machine controls to complex industrial automation systems, logic gates determine how controllers respond to changing inputs and...
Industrial firewalls play a critical role in OT cybersecurity, protecting PLC, DCS, and SCADA networks through segmentation, ingress/egress control, and IDS/IPS integration aligned with IEC 62443...
Modern robotic grippers are evolving beyond traditional mechanical jaws. From gecko-inspired adhesive systems and soft food-grade grippers to AI-powered warehouse tools, advanced gripping...
