Manufacturer: Bently Nevada
Product No.: AM3100T2-Z2
Country of origin:Съединени щати
Product Type: Accelerometer Sensor
Barcode: 8537101190
Payment: T/T, Western Union
Weight: 62g
Dimensions: 1.8cm x 1.6cm x 123cm
Shipping port: Xiamen
Warranty: 12 months
The AM3100T2-Z2 is an Integrated Electronics Piezo-Electric (IEPE) accelerometer optimized for obtaining high quality vibration signals in harsh industrial environments. Its piezo sensing element provides exceptional dynamic range, frequency range, and linearity, while the integrated amplifier boosts the signal and improves immunity to electrical noise.
The sensor requires an industry standard constant-current power supply and provides an output voltage proportional to the acceleration signal, allowing interface with a wide variety of condition monitoring systems.
The AM3100T2-Z2 features a top-exit connector configuration, 100 mV/g sensitivity, and Zone 2 hazardous-area certification.
| ParameterValue | |
| Sensitivity, ±5% @25°C | 100 mV/g |
| Acceleration range | 80 g peak |
| Amplitude nonlinearity | 1% |
| Frequency response ±10% | 0.7-9,000 Hz |
| Frequency response ±3 dB | 0.4-14,000 Hz |
| Resonant frequency | 30 kHz |
| Transverse sensitivity, max | ±5% of axial |
| Temperature response | -55°C : -20% / +120°C : +10% |
| ParameterValue | |
| Voltage source | 18-30 Vdc |
| Current regulating diode | 2-10 mA |
| Broadband electrical noise @ 2.5 Hz to 25 kHz | 500 μg |
| Spectral electrical noise @ 10 Hz | 7 μg/√Hz |
| Spectral electrical noise @ 100 Hz | 4 μg/√Hz |
| Spectral electrical noise @ 1000 Hz | 2 μg/√Hz |
| Output Impedance, max | 100 Ω |
| Bias output voltage | 12 Vdc |
| Grounding | Case isolated, internally shielded |
| ParameterValue | |
| Temperature range | -55°C to 120°C |
| Vibration limit | 500 g peak |
| Shock limit | 5,000 g peak |
| Electromagnetic sensitivity, equiv g, max | 70 μg/gauss |
| Sealing | Hermetic |
| Base strain sensitivity, max | 0.0002 g/μstrain |
| ParameterValue | |
| Sensing element design | PZT ceramic / shear |
| Weight | 62 grams |
| Case material | 316L Stainless Steel |
| Mounting | ¼-28 UNF tapped hole |
| Connector | Top exit, 2-pin, MIL-C-5015 style |
| Recommended cabling | Shielded, twisted pair, no longer than 100 feet |
| Connector PinFunction | |
| Shell | Ground |
| A | Power / Signal |
| B | Common |
Frequency response and spectral noise values are typical.
Install the sensor on a clean, flat, and rigid mounting surface. Remove paint, rust, grease, and debris before installation to ensure proper mechanical coupling and accurate vibration transmission.
Poor mounting surfaces may reduce high-frequency response and introduce measurement errors.
Use the supplied ¼-28 mounting stud for installation.
Installation recommendations:
Use shielded twisted-pair cable as recommended by the manufacturer.
For best signal quality:
Recommended cable length should not exceed 100 feet.
The sensor uses a top-exit 2-pin MIL-C-5015 style connector.
In wet or outdoor environments:
The hermetic sensor body helps protect against moisture ingress when properly installed.
The AM3100T2-Z2 requires an IEPE constant-current power source.
Required electrical supply:
Verify compatibility with the monitoring system before commissioning.
The sensor is case isolated and internally shielded to help reduce ground loop problems.
Recommended practices:
The AM3100T2-Z2 is approved for Zone 2 hazardous locations.
Installation must comply with:
Ensure all associated wiring, barriers, and cable glands meet hazardous-area installation requirements.
The AM3100T2-Z2 is an IEPE accelerometer designed for industrial vibration monitoring applications.
The sensor sensitivity is 100 mV/g (±5% at 25°C).
The sensor supports an acceleration range of 80 g peak.
Frequency response specifications are:
The sensor requires:
Yes. The AM3100T2-Z2 is certified for Zone 2 hazardous-area applications.
The device uses a top-exit 2-pin MIL-C-5015 style connector.
No. The sensor is case isolated and internally shielded.
The operating temperature range is -55°C to 120°C.
Yes. The sensor has a hermetic seal and can operate in wet environments when proper sealed connectors and cables are used.
The mounting interface is a ¼-28 UNF tapped hole.
Shielded twisted-pair cable is recommended, with a maximum length of 100 feet.
Yes. The device includes reverse wiring protection to help prevent damage caused by incorrect wiring.
Глобална експресна доставка
Връщания и гаранция
Поръчките се обработват и доставят от понеделник до петък (с изключение на официалните празници).
За пълна информация относно допустимост, такси за презареждане и международни връщания, моля, разгледайте нашия официален Политика за възстановяване и връщане .
| Color pattern |
Злато
Сребърен
|
| Country of origin |
Съединени щати
|
Тази статия обяснява как интегрираните електрически задвижвания, като серията e-Actuator на SMC, трансформират индустриалното управление на движението, като заменят традиционните пневматични и...
Тази статия обяснява как PLC системите изпълняват основни математически операции като събиране, изваждане, умножение, деление, модуло и степенуване в индустриалната автоматизация. Показва как тези...
Статията обяснява няколко усъвършенствани булеви логически функции, използвани в програмирането на PLC, извън основните операции AND, OR и NOT. Тя разглежда как инструменти като таблици на...
Булевата логика е основата на всяка програма за PLC. От прости машинни управления до сложни индустриални автоматизационни системи, логическите врати определят как контролерите реагират на променящите...
Индустриалните защитни стени играят ключова роля в киберсигурността на OT, като защитават мрежите PLC, DCS и SCADA чрез сегментация, контрол на входящия/изходящия трафик и интеграция на IDS/IPS в...
Съвременните роботизирани захвати се развиват отвъд традиционните механични челюсти. От системи с лепкави повърхности, вдъхновени от геконите, и меки захвати за хранителни продукти до инструменти за...
