Manufacturer: Omron
Product No.: NX-TS2102
Country of origin:Япония
Product Type: Temperature Input Units
Payment: T/T, Western Union
Weight: 70g
Dimensions: 12 (W) x 100 (H) x 71 (D) mm
Shipping port: Xiamen
Warranty: 12 months
Designed for high-speed thermal monitoring within the Sysmac automation platform, the Omron NX-TS2102 delivers high-resolution temperature data acquisition directly to the NX bus interface. This 2-point thermocouple input unit enables real-time temperature tracking with an ultra-low conversion cycle time of 10 ms per unit, making it an excellent choice for dynamic closed-loop heating and cooling processes. Utilizing a screwless clamping terminal block with 16 connection terminals, the module simplifies field commissioning while ensuring vibration-resistant wire terminations in demanding industrial environments.
| Parameter | Specification |
|---|---|
| Manufacturer | Omron |
| Model Number | NX-TS2102 |
| Series | NX I/O System |
| Unit Type | Temperature Input Unit (Thermocouple Type) |
| Number of Inputs | 2 channels |
| Conversion Time | 10 ms / Unit |
| Resolution | 0.01 degC maximum |
| Input Conversion Range | +/-20 degC of the nominal sensor input range |
| Input Impedance | 20 kOhm minimum |
| Absolute Maximum Rating | +/-130 mV |
| Disconnection Detection Current | Approximately 0.1 uA |
| Warm-up Period | 45 minutes |
| Isolation Method | Power: Transformer; Signal: Digital Isolator (Input-to-NX Bus and Channel-to-Channel) |
| Insulation Resistance | 20 MOhm minimum between isolated circuits (at 100 VDC) |
| Dielectric Strength | 510 VAC between isolated circuits for 1 minute (leakage current 5 mA max) |
| NX Unit Power Consumption | 1.15 W max (on CPU/Control Unit); 0.80 W max (on Coupler Unit) |
| Module Dimensions | 12 mm (W) x 100 mm (H) x 71 mm (D) |
| Net Weight | 0.07 kg |
| Country of Origin | Japan |
| Shipping Weight (Calculated) | 1.00 kg |
The NX-TS2102 is highly compatible across the entire Sysmac platform, including NX102, NX1P2, and NJ series controllers when utilizing EtherCAT or EtherNet/IP coupler units. If your process requires RTD sensors (such as Pt100) instead of thermocouples, consider the alternative NX-TS2101 model. For installations requiring higher density in a single slot, the 4-channel NX-TS3102 is a direct functional alternative with similar conversion characteristics.
To achieve the specified maximum conversion resolution of 0.01 degC, the module requires a warm-up period of 45 minutes after system start-up. In high-density control enclosures, avoid placing high-power components (like contactors, variable frequency drives, or power supplies) immediately adjacent to the temperature unit, as localized thermal radiation can distort the built-in cold junction compensation (CJC) reference reading.
When wiring the 16-pin screwless terminal block, ensure that thermocouple extension wires match the correct alloy chemistry of the sensor type (e.g., K-type extension wire for K-type thermocouples) up to the terminal clamp to prevent parasitic junctions. Shielded thermocouple cables should be used, with the shield terminated at a single low-impedance ground point to minimize electrical noise induced from adjacent mains wiring.
CRITICAL WARNING
Always isolate all system power sources (mains supply and external I/O power) before inserting or removing the module from the NX bus rack assembly. Failure to completely de-energize the unit during terminal maintenance or expansion may cause permanent damage to the integrated digital isolators or interrupt synchronous communication on the active backplane.
Mount the module onto the standard 35 mm DIN rail. Engage the upper hook of the NX Unit connector with the DIN rail, then press downward until the locking lever clicks securely into position.
Connect the adjacent NX Units together, sliding them firmly until the side-plane bus connectors link cleanly. Secure the end plate on the rightmost unit of the assembly.
Perform wiring of the thermocouple cables using solid wires or ferrules. Insert a flat-blade screwdriver into the terminal release hole, insert the stripped wire into the clamp terminal, and release the screwdriver to lock.
Глобална експресна доставка
Връщания и гаранция
Поръчките се обработват и доставят от понеделник до петък (с изключение на официалните празници).
За пълна информация относно допустимост, такси за презареждане и международни връщания, моля, разгледайте нашия официален Политика за възстановяване и връщане .
| Country of origin |
Япония
|
Тази статия обяснява как интегрираните електрически задвижвания, като серията e-Actuator на SMC, трансформират индустриалното управление на движението, като заменят традиционните пневматични и...
Тази статия обяснява как PLC системите изпълняват основни математически операции като събиране, изваждане, умножение, деление, модуло и степенуване в индустриалната автоматизация. Показва как тези...
Статията обяснява няколко усъвършенствани булеви логически функции, използвани в програмирането на PLC, извън основните операции AND, OR и NOT. Тя разглежда как инструменти като таблици на...
Булевата логика е основата на всяка програма за PLC. От прости машинни управления до сложни индустриални автоматизационни системи, логическите врати определят как контролерите реагират на променящите...
Индустриалните защитни стени играят ключова роля в киберсигурността на OT, като защитават мрежите PLC, DCS и SCADA чрез сегментация, контрол на входящия/изходящия трафик и интеграция на IDS/IPS в...
Съвременните роботизирани захвати се развиват отвъд традиционните механични челюсти. От системи с лепкави повърхности, вдъхновени от геконите, и меки захвати за хранителни продукти до инструменти за...
