ABB 07 DC 92 GJR5 2522 00 R0101 | AC31 32-Channel Digital I/O Module

Only 6 item(s) left in stock

Manufacturer: ABB
Product No.: GJR5252200R0101
Country of origin:Németország
Product Type: Digital I/O Module
Barcode: 85389091
Payment: T/T, Western Union
Weight: 450g
Dimensions: 120 × 140 × 85 mm
Shipping port: Xiamen
Warranty: 12 months

ABB 07 DC 92 (07DC92), order number GJR5 2522 00 R0101, is a remote digital input/output module for the AC31 automation system and CS31 system bus. Unlike fixed I/O modules, all 32 channels can be individually configured by the user program as digital inputs, digital outputs, or re-readable outputs, providing exceptional flexibility for distributed control applications.

The module divides its 32 channels into four electrically isolated groups with eight channels per group. Each output uses transistor technology with a nominal load capacity of 500 mA and incorporates electronic overload and short-circuit protection. Built-in diagnostic functions, channel status LEDs, and communication monitoring assist maintenance personnel during commissioning and fault investigation.

The ABB 07 DC 92 occupies two digital addresses on the CS31 system bus and can also be configured as a dedicated output module when input addresses are not required. This flexibility makes the module suitable for machine automation, process control systems, utility installations, and industrial modernization projects requiring distributed field I/O.

Technical Specifications

Manufacturer	ABB
Model	07 DC 92 (07DC92)
Order Number	GJR5 2522 00 R0101 (GJR5252200R0101)
Product Type	Digital Input / Output Module
System	AC31 / Advant Controller 31
Communication Bus	CS31 System Bus
Bus Interface	EIA RS-485
Number of Configurable Channels	32
Channel Modes	Input, Output, Re-readable Output
Channel Groups	4 Groups × 8 Channels
Electrical Isolation	Group-to-Group and Bus-to-I/O Isolation
Rated Supply Voltage	24 VDC
Rated Signal Voltage	24 VDC
Maximum Current Consumption	0.15 A (without load)
Maximum Supply Terminal Load	4.0 A
Maximum Power Dissipation	5 W (outputs unloaded), 10 W (outputs loaded)
Reverse Polarity Protection	Supported
Operating Temperature	0°C to +55°C
Status Indicators	32 Yellow LEDs + 1 Red Fault LED
Address Setting	DIL Switch Under Side Cover

Digital Input Characteristics

Input Channels	32
Input Delay	Typical 7 ms
Input Voltage	24 VDC
Signal 0 Range	-30 V to +5 V
Signal 1 Range	+13 V to +30 V
Input Current at 24 V	Typical 7 mA
Reference Potentials	ZP0, ZP1, ZP2, ZP3

Digital Output Characteristics

Output Type	Transistor Outputs
Output Channels	32
Nominal Output Current	500 mA per Channel
Maximum Group Current	4 A per Group
Leakage Current	< 0.5 mA
Overload Protection	Integrated
Short-Circuit Protection	Integrated
Current Limitation	Supported
Overload Threshold	Approx. 0.7 A
Automatic Reactivation	After Short-Circuit or Overload Removal
Inductive Load Protection	Internal Varistor

Installation & Commissioning Guide

Field commissioning of the ABB 07 DC 92 usually begins with verification of the DIL address switch, CS31 bus wiring, and 24 VDC power connections. The module reads its address configuration only during power-up initialization, therefore any address change requires a restart before it becomes effective.

Install the module vertically with the connectors facing upward and downward. Natural convection cooling must remain unobstructed by cable ducts, power supplies, or other cabinet components.

Mounting Method	DIN EN 50022 Rail or 4 × M4 Screws
Installation Position	Vertical
Cooling Method	Natural Convection
Width × Height × Depth	120 × 140 × 85 mm
Weight	450 g

During startup all LEDs illuminate briefly while the module performs initialization. If the CS31 bus is not operating correctly, the red fault LED flashes continuously. Before replacing the module, engineers should verify address settings, bus polarity, controller configuration, and cable continuity.

If an overload or short circuit occurs, the affected output channel is automatically switched off by the protection circuitry. The corresponding channel LED flashes until the fault condition is removed and the output is reactivated.

Product Image	Model Number / Title	Condition	Availability	Action
	ABB 07 DO 90-S GJR5 2508 00 R202 AC31-S Safety Binary Output Module	Original New	In Stock	View Details

Key Features:

#Advant Controller 31 #Digital I/O Modules

Product Documentation

Technical Datasheet (PDF) Complete specifications and technical drawings.

Why does the red diagnostic LED continue flashing even though the module has power?

The module has completed its startup sequence but has not established normal communication on the CS31 bus. In most cases the cause is an incorrect station address, communication wiring fault, controller configuration issue, or loss of bus continuity.

Why are several channels reporting faults when only one field device appears to be defective?

The output circuits are arranged in protected groups. A short circuit or overload on a single field device can trigger protection for the affected group, causing multiple channels to report a fault condition until the source of the problem is removed.

What should be checked before replacing a suspected faulty module?

Before replacing the module, verify the 24 VDC supply, CS31 communication status, field wiring integrity, terminal tightness, and controller diagnostics. Communication and wiring issues are more common than actual hardware failure.

Why does an output channel switch off unexpectedly during normal operation?

An output may be automatically disconnected if the load current exceeds the protection threshold or if a short circuit is detected. The protection circuitry prevents damage to the output stage and attempts recovery after the fault condition is removed.

Why is an output LED active while the connected device remains de-energized?

The LED only indicates the output command state. Open field wiring, damaged loads, blown protection devices, voltage drops, or incorrect terminal assignments can prevent the connected device from operating even when the output is commanded ON.

Do address switch changes become effective immediately?

No. The module reads its address configuration during startup. Any change to the DIL switch setting requires a restart before the new address becomes active on the CS31 network.

Can the module operate with both input and output channels configured at the same time?

Yes. Each channel can be individually assigned by the application program. Input, output, and re-readable output functions can coexist within the same module according to system requirements.

What is the most common cause of intermittent I/O faults in service?

Intermittent faults are typically associated with loose terminals, unstable power supplies, damaged field cables, excessive vibration, moisture ingress, or poor communication connections rather than permanent module failure.

Can a replacement module be installed without modifying the AC31 application program?

In most systems, yes. The module does not store application-specific channel assignments. After replacement, engineers should verify the address setting, communication status, and field wiring before returning the system to operation.

Why do outputs repeatedly switch OFF and then recover automatically?

This behavior usually indicates that the electronic protection circuit is responding to an overload or short-circuit condition. The module removes power from the affected output and periodically attempts to restore operation until the fault is cleared.

What should be investigated if communication is lost after maintenance work?

Address settings, CS31 bus polarity, terminal connections, shield continuity, and recently modified field wiring should be inspected first. Most post-maintenance communication problems are related to wiring changes rather than controller or module failure.

Can the module be used as a dedicated output station?

Yes. The 07 DC 92 can be configured as an output-only station when input processing is not required, allowing available address resources on the CS31 network to be used more efficiently.

Globális expressz szállítás

Normál szállítás: 4-6 munkanap a DHL, FedEx és UPS szolgáltatásával.
Gyors kiszállítás: A raktáron lévő, 14:00 (GMT+8) előtt leadott megrendeléseket aznap feladjuk.
Világszintű lefedettség: Több mint 150 országban szolgálunk ki, beleértve a gyors szállítást Szaúd-Arábiába és az Egyesült Arab Emírségekbe.

Visszaküldés és garancia

30 napos garancia: Csak a raktáron lévő termékek eredeti, gyári zárt csomagolásban történő visszaküldését fogadjuk el.
12 hónapos garancia: Minden ipari alkatrészünket szakmai műszaki garancia védi.

A megrendeléseket hétfőtől péntekig dolgozzuk fel és szállítjuk (állami ünnepnapok kivételével).

A teljes jogosultság, a készletfeltöltési díjak és a nemzetközi visszaküldési részletek megtekintéséhez kérjük, tekintse meg hivatalos oldalunkat Visszatérítési és Visszaküldési Szabályzat .

TECHNICAL SPECIFICATIONS

Color pattern	Szürkésfehér
Country of origin	Németország
Power source	DC áram

Nemrég megtekintett termékek

Műszaki ismeretek

Electric Actuators Designed to Replace Fluids: Hands-on Tutorial

Elektromos működtetők, amelyek a folyadékenergia-rendszereket váltják ki: Gyakorlati ipari automatizálási útmutató

Ez a cikk bemutatja, hogyan alakítják át az integrált elektromos működtetők, például az SMC e-Actuator sorozata, az ipari mozgásvezérlést azáltal, hogy kiváltják a hagyományos pneumatikus és...

2026. június 23.

$Math Operations Using OpenPLC for Industrial Automation Applications$

ABB 07 DC 92 GJR5 2522 00 R0101 | AC31 32-Channel Digital I/O Module