Pengilang: Lenze
No. Produk: EVS9326-EI
Negara asal:Jerman
Jenis Produk: Servo Drives
Kod Bar: 85044095
Pembayaran: T/T, Western Union
Berat: 7500g
Dimensi: 35.00 x 25.00 x 13.50 cm
Pelabuhan penghantaran: Xiamen
Jaminan: 12 bulan
Designed for high-performance motion control within coordinated multi-axis systems, the Lenze EVS9326-EI operates as a closed-loop servo inverter within the legacy 9300-Series family. This unit delivers precise speed, torque, and position control for demanding industrial automation architectures, providing a rated power output of 11.0 kW in a robust, cabinet-mounted form factor.
| Parameter | Value |
|---|---|
| Manufacturer | Lenze |
| Model Number | EVS9326-EI |
| Product Series | 9300-Series |
| Product Type | Servo Drive / Controller |
| Rated Power | 11.0 kW |
| Enclosure Rating | IP20 |
| Product Phase | Phase-Out (Legacy Spare Part) |
| Commodity Code | 85044095 |
| Export Control Classification (ECCN) | N |
| Dimensions (H x W x D) | 35.00 x 25.00 x 13.50 cm |
| Weight | 7.50 kg |
| Terminal / Connector | Function / Assignment |
|---|---|
| X1 | Mains Input Connection / DC Bus Link |
| X2 | Motor Phase Output & Motor Temperature Sensor (PTC) |
| X3 | Resolver Feedback Input |
| X4 | Incremental Encoder Input / Master-Slave Interface |
| X5 | Analog and Digital Control Inputs/Outputs |
| X6 | System Bus (CAN) Interface |
The "EI" suffix designates this unit as the standard execution featuring incremental encoder input/output capabilities. It can directly replace older EVS9326-ES units in most applications, provided the parameter set is migrated and verified using Lenze Global Drive Control (GDC) software. Ensure that the firmware version of the replacement unit matches or exceeds the original to prevent fieldbus mapping mismatches.
Because this drive is IP20 rated, it must be installed in a clean, dust-free control cabinet. At 11.0 kW continuous output, thermal dissipation is significant. Maintain a minimum vertical clearance of 100 mm above and below the unit to prevent localized overheating. For high-inertia applications, an external braking resistor must be connected to terminals UG+ and BR to prevent overvoltage trips (fault code OU) during rapid deceleration.
Always use double-shielded, twisted-pair cabling for the resolver (X3) and encoder (X4) feedback loops. Ground the cable shields at both ends using low-impedance EMC shield clamps to prevent high-frequency noise from corrupting the feedback signal. When integrating the drive into a CAN network via X6, ensure a 120-ohm terminating resistor is physically installed at both ends of the bus line.
CRITICAL WARNING
Isolate all input power sources (mains and 24 VDC auxiliary control power) before performing installation or maintenance. Wait at least 5 minutes after power-off to allow the internal DC bus capacitors to fully discharge below 60 VDC. Verify the absence of voltage with a calibrated multimeter at the DC bus terminals before handling.
Mount the drive vertically on a flat, conductive, and grounded backplate inside the control cabinet to ensure optimal heat transfer and EMC grounding.
Connect the protective earth (PE) conductor directly to the drive's grounding terminal before making any other electrical connections.
Wire the mains input power to terminal X1 and the motor phases to terminal X2 using shielded motor cables to minimize electromagnetic radiation.
Connect the resolver or encoder feedback cable to the respective port (X3 or X4) and route control signals away from high-power cabling.
Penghantaran Ekspres Global
Pemulangan & Jaminan
Pesanan diproses dan dihantar Isnin-Jumaat (tidak termasuk cuti umum).
Untuk kelayakan penuh, yuran penyimpanan semula, dan butiran pemulangan antarabangsa, sila lihat rasmi kami Polisi Pemulangan & Bayaran Balik .
| Country of origin |
Jerman
|
Logik Boolean adalah asas bagi setiap program PLC. Dari kawalan mesin yang mudah hingga sistem automasi industri yang kompleks, pintu logik menentukan bagaimana pengawal bertindak balas terhadap...
Firewall industri memainkan peranan penting dalam keselamatan siber OT, melindungi rangkaian PLC, DCS, dan SCADA melalui segmentasi, kawalan masuk/keluar, dan integrasi IDS/IPS yang selaras dengan...
Pengapit robotik moden sedang berkembang melebihi rahang mekanikal tradisional. Daripada sistem pelekat yang diinspirasikan oleh cicak dan pengapit lembut gred makanan hingga alat gudang yang...
Dari pemampat DC yang digerakkan tali ke troli lombong bertenaga bateri, operasi perlombongan awal menandakan titik perubahan dalam elektrifikasi industri. Artikel ini meneroka bagaimana motor...
Factory I/O sedang mengubah pendidikan PLC dengan menyediakan simulasi industri 3D yang mendalam untuk pelajar, jurutera, dan pasukan penyelenggaraan. Platform ini merapatkan jurang antara teori dan...
Tutorial ini mengkaji bagaimana fungsi PLC terbina dalam pemacu servo CMZ SBD dapat melaksanakan program gerakan berdiri sendiri, termasuk logik homing, kawalan kedudukan, dan pergerakan paksi...
