Mitsubishi Electric FR-F740-45K-CHT1 F700 Series Energy Saving Inverter

Stokta sadece 10 adet kaldı

Üretici: Mitsubishi Electric
Ürün No.: FR-F740-45K-CHT1
Menşei ülke:Amerika Birleşik Devletleri
Ürün Türü: Variable Frequency Drives
Ödeme: T/T, Western Union
Ağırlık: 35000g
Gönderim limanı: Xiamen
Garanti: 12 ay

Description

Optimizing energy consumption in heavy-duty pump and fan applications, the Mitsubishi Electric FR-F740-45K-CHT1 variable frequency drive provides precise three-phase speed control within the F700 Series automation architecture. This high-capacity inverter is engineered to maximize system efficiency through advanced optimum excitation control, minimizing electrical losses in induction motors. Note that the FR-F740-45K-CHT1 is now discontinued by the manufacturer; the recommended modern replacement is the FR-F840-00930-2-60 power-saving frequency inverter, which offers updated control algorithms and physical drop-in compatibility for most fan and blower systems.

Features

Optimum Excitation Control: Automatically adjusts motor flux to achieve maximum efficiency under variable torque loads.
Dual Performance Ratings: Optimized for high-efficiency variable torque application envelopes.
Integrated EMC Filter: Built-in radio noise filter helps suppress electromagnetic interference to adjacent instrumentation.
Advanced Diagnostics: Monitors lifetime metrics of internal components, including cooling fans and smoothing capacitors.
Network Integration: Supports integration into standard industrial bus architectures via serial communications.

Applications

Municipal water treatment facilities and booster pumping stations.
Large-scale industrial HVAC cooling towers and air handling units (AHU).
Supply and exhaust ventilation fans in heavy industrial facilities.
Secondary circulation pumps in manufacturing process cooling loops.

Technical Specifications

Parameter	Specification Value
Manufacturer	Mitsubishi Electric
Model Reference	FR-F740-45K-CHT1
Series Name	F700 Series
Replacement Part Number	FR-F840-00930-2-60
Applied Motor Capacity	45 kW
Rated Capacity	64.8 kVA
Rated Output Current	85 A (at 40 degC ambient) / 72 A (at 50 degC ambient)
Overload Current Rating	120% for 60 seconds, 150% for 3 seconds (inverse time characteristics)
Rated Input Voltage / Frequency	Three-phase 380 to 480 V AC, 50Hz / 60Hz
Allowable Voltage Fluctuations	323 to 528 V AC (50Hz / 60Hz)
Control Methodology	V/F control, Advanced magnetic flux vector control, Optimum excitation control
Cooling Method	Forced air cooling
Net Weight	35 kg
Shipping Weight (Calculated)	40 kg

Connections and Interfaces

Terminal / Pin Label	Functional Assignment
R/L1, S/L2, T/L3	Three-phase AC power input terminals
U, V, W	Three-phase variable frequency output terminals to the motor
STF / STR	Start Forward / Start Reverse digital control inputs
SD	Common terminal for contact input signals (sink) and isolated 24 V DC power common
RX / TX / SG	Modbus RTU serial RS-485 interface connection points

Empirical Engineering Insights

Alternative Models & Compatibility

When migrating from the discontinued FR-F740-45K-CHT1 to the current-generation FR-F840-00930-2-60, verify the overall envelope size. While both drives are optimized for 45 kW loads, physical terminal block layout structures differ slightly. The F800 series offers superior parameter cloning capability via a built-in USB port, removing the reliance on custom serial communications cables during setup.

Application Pitfalls & Engineering Notes

This unit is rated for variable torque systems. Operating it on constant-torque applications (such as cranes or positive displacement pumps) can cause persistent overcurrent trip faults (E.OC1 to E.OC3) on ramp-up. If the fan or pump system exhibits high backdraft or regenerative loads during braking, an external dynamic braking resistor must be specified to prevent DC bus overvoltage trips (E.OV2).

Commissioning & Wiring Tips

To ensure accurate overload protection, ensure that Parameter 9 (Electronic Thermal O/L Relay) is programmed to match the exact nameplate full-load current (FLA) of the attached motor rather than the drive’s maximum current rating. Ensure that the logic control jumper (Sink/Source selector) on the control board is set correctly before landing your control wiring to avoid potential logic circuit damage.

Installation Guidelines

CRITICAL WARNING: Hazardous voltages remain present on the internal DC bus capacitors even after primary input power has been isolated. Disconnect all primary power supplies and verify that the charge lamp is completely off. Wait at least 10 minutes and measure the voltage across terminals P/+ and N/- with a calibrated multimeter to confirm it is below 50 V DC before executing any maintenance or wiring.

Mount the inverter vertically inside a clean, dust-free electrical enclosure. Ensure there is a minimum of 100 mm top and bottom clearance to permit adequate convective airflow from the integrated cooling fans.

Route incoming line power to terminals R/L1, S/L2, and T/L3, and connect the output motor cables directly to terminals U, V, and W. Do not connect line power directly to the output terminals as this will permanently destroy the inverter module.

Terminate all shielding and ground conductors to the dedicated system ground block. Keep analog speed reference control wiring shielded and physically routed away from noisy motor cables to avoid noise induction.

Key Features:

What is the recommended replacement for the discontinued FR-F740-45K-CHT1?

The recommended modern replacement is the Mitsubishi Electric FR-F840-00930-2-60 power-saving inverter, which provides advanced energy-saving arithmetic and compatible application characteristics.

What are the rated output currents for this variable frequency drive?

The unit outputs a maximum rated current of 85 A at ambient conditions up to 40 degC, which derates to 72 A if operating in ambient environments up to 50 degC.

Can this unit be used for constant-torque industrial applications?

No. The F700 series, including the FR-F740-45K-CHT1, is specifically rated and designed for variable torque loads such as pumps and centrifugal fans.

How long must I wait before performing wiring maintenance on the drive?

You must wait at least 10 minutes after disconnecting input power and confirm that the internal charge LED is completely off before servicing terminal connections.

Küresel Ekspres Kargo

Standart Teslimat: DHL, FedEx ve UPS ile 4-6 iş günü.
Hızlı Gönderim: Saat 14:00 (GMT+8) öncesi verilen stoktaki siparişler aynı gün gönderilir.
Dünya Çapında Hizmet: Suudi Arabistan ve BAE'ye hızlı teslimat dahil 150'den fazla ülkeye hizmet veriyoruz.

İadeler ve Garanti

30 Günlük Garanti: Stokta bulunan ürünler, orijinal, fabrika mühürlü ambalajında iade kabul edilir.
12 Aylık Garanti: Her endüstriyel bileşen profesyonel teknik garantimizle desteklenmektedir.

Siparişler Pazartesi-Cuma (resmi tatiller hariç) işlenir ve teslim edilir.

Tam uygunluk, stok yenileme ücretleri ve uluslararası iade detayları için lütfen resmi sayfamızı inceleyin İade ve Geri Ödeme Politikası .

TECHNICAL SPECIFICATIONS

Country of origin

Mitsubishi Electric FR-F740-45K-CHT1 F700 Series Energy Saving Inverter