Bently Nevada 330101-00-50-20-02-CN 3300 XL 8 mm Proximity Probe

Description

The Bently Nevada 330101-00-50-20-02-CN is an 8 mm proximity probe designed for non-contact vibration and shaft position measurements in critical rotating machinery. As a key component of the 3300 XL 8 mm Proximity Transducer System, this specific configuration features a fully threaded 5.0-inch overall case length (0.0-inch unthreaded length) and a 3/8-24 UNF thread, providing direct casing mounting options without mechanical armor. Engineered with a total cable length of 2.0 meters (6.6 feet) and terminated with a miniature coaxial ClickLoc connector, this probe connects seamlessly to standard extension cables and 3300 XL Proximitor sensors. This variant is specifically designated with the -CN suffix, certifying it with the China hazardous area approval package (NEPSI and CCC markings) for deployment in regulated industrial environments across China.

Utilizing eddy current operating principles, this proximity probe provides highly precise, reliable displacement measurements of turbine shafts, compressor rotors, and pump bearings. Its rugged polyphenylene sulfide (PPS) tip is molded to a stainless steel probe body with a built-in Viton O-ring seal, ensuring excellent chemical resistance and pressure sealing integrity against machine lubricants and gases.

Features

• Fully Threaded Standard Case: Features a 5.0-inch overall case length with 0.0-inch unthreaded length for solid, adjustable thread engagement.
• 2.0-Meter Standard Cable: Equipped with a 2.0-meter (6.6 feet) integrated 75-ohm triaxial FEP insulated standard cable.
• ClickLoc Coaxial Connector: Features a miniature gold-plated coaxial ClickLoc connector for quick, reliable, and vibration-resistant connections.
• Armorless Design: Standard unarmored flexible FEP jacket for ease of routing in space-constrained bearing housings.
• -CN Approval Package: Specifically certified with the China hazardous area approval package, including NEPSI and CCC certifications.
• Robust Environmental Protection: Highly resistant to chemical erosion from high-pH or low-pH solutions and sealed to handle differential machine pressures.

Applications

The 330101 proximity probe is widely utilized in heavy industrial rotating machinery monitoring systems, including:

• Steam turbine and gas turbine shaft vibration and axial position measurement.
• Centrifugal compressor and high-pressure pump rotor displacement monitoring.
• Hydroelectric generator shaft alignment and thermal expansion tracking.
• Critical machinery protection systems (TSI) in power generation, oil & gas, and petrochemical refining.

Ordering Information

Technical Specifications

Connections and Interfaces

The integrated standard cable is terminated with a miniature coaxial ClickLoc connector. This connector features gold plating to minimize electrical noise and is designed to provide secure, finger-tight snap connections to the matching female ClickLoc connector of the standard extension cable.

Installation Guidelines

• Ensure the probe gap is calibrated and adjusted to the correct DC voltage (typically -10 Vdc corresponding to a nominal 1.27 mm or 50 mils gap) using a proximity calibrator before locking in place.
• To prevent binding during installation, ensure the maximum length of thread engagement does not exceed the mechanical limit of 0.563 inches (14.3 mm).
• Employ a class matching external threads when tapping mounting holes, and secure the probe using a lock nut with safety wire holes if required by machinery vibrations.
• Route the FEP-insulated coaxial cable through a dedicated conduit to protect against physical wear, keeping the minimum permissible cable bend radius of 25.4 mm (1.0 inch) in mind.
• Always observe proper shielding and grounding practices: connect the shield of the extension cable to the Proximitor sensor terminal block, and isolate the sensor housing from the machine ground to prevent ground loops.

Compliance and Certifications

• NEPSI: Certified for hazardous area applications in China.
• CCC: China Compulsory Certificate for industrial safety and electrical compliance.
• Hazardous Area approvals (with -CN package): Ex ia IIC T5...T1 Ga, Ex ia IIIC T90degC...T280degC Dc.
• Electrical Safety: Meets standard Bently Nevada entity parameters when paired with approved Proximitor sensors (Ui = -28V, Ii = 140 mA, Pi = 0.91 W).