Manufacturer: Mitsubishi Electric
Product No.: AJ65SBTB1-32TE1
Country of origin:Съединени щати
Product Type: PLC I/O Modules
Payment: T/T, Western Union
Weight: 260g
Dimensions: 179 mm x 50 mm x 40 mm
Shipping port: Xiamen
Warranty: 12 months
Facilitating high-density remote discrete control in decentralized automation architectures, the Mitsubishi Electric AJ65SBTB1-32TE1 operates as a 32-point source transistor output block designed for integration into CC-Link open fieldbus networks. This remote I/O module features photocoupler isolation between the internal logic circuitry and the field terminal interface, suppressing electrical transients and protecting upstream network devices. Built with a compact footprint, the module simplifies field wiring through an integrated terminal block interface and supports both 12VDC and 24VDC load environments, making it suitable for distributed control panels in process and manufacturing automation.
| Parameter | Technical Value |
|---|---|
| Manufacturer | Mitsubishi Electric |
| Model Number | AJ65SBTB1-32TE1 |
| Product Type | Transistor Output Module (Source Type) |
| Network Protocol | CC-Link (Remote I/O Station) |
| Number of Output Points | 32 Points |
| Output Logic | Source (PNP Type) |
| Isolation Method | Photocoupler |
| Rated Load Voltage | 12 VDC / 24 VDC |
| Operating Load Voltage Range | 10.2 VDC to 26.4 VDC (Ripple ratio within 5%) |
| External Connections | Screw Terminal Block |
| Net Weight | 0.26 kg |
| Shipping Weight (Calculated) | 0.45 kg |
| Dimensions (W x H x D) | 179 mm x 50 mm x 40 mm |
| Terminal Block Label | Function / Circuit Assignment |
|---|---|
| DA, DB, DG | CC-Link Network Data Lines (A, B, Ground) |
| SLD / FG | Shield Line Connection / Frame Ground |
| 24V / 0V (Power) | External Module Power Input (24VDC) |
| Y00 to Y1F | Transistor Source Output Channels (32 Points) |
| COM | Common Terminal for External Load Power Supply |
The AJ65SBTB1-32TE1 is a source-type (PNP) output module. If replacing an older AJ65SBTB1-32T model, note that the non-suffix "T" variant is a sink-type (NPN) module. Direct replacement without swapping the common return paths on your external field loads will result in a short circuit or failure of the loads to actuate. Ensure that your system wiring diagrams specifically specify PNP field switching logic before installing this unit.
When switching inductive loads such as solenoid coils or contactors, ensure external surge suppressors (flyback diodes) are installed directly across the load terminals. While the AJ65SBTB1-32TE1 includes internal clamp protection, repeated high-frequency inductive energy dissipation can cause premature thermal wear on the output transistors. Additionally, respect the maximum aggregate current limit per common group to avoid local trace overheating inside the module during simultaneous 32-point actuation.
During CC-Link commissioning, set the station number switches and baud rate rotary switches on the module faceplate prior to powering up the station. The master module will not register on-the-fly network configuration changes. Always verify that a 110-ohm terminating resistor is installed at both physical ends of the CC-Link trunk line to stabilize communication waveforms and prevent transmission packet loss.
CRITICAL WARNING: Ensure all main AC/DC supply voltages to the control panel are completely de-energized and locked out before attempting installation, removal, or terminal wiring modification. Failure to disconnect power can result in field circuit damage or electrical shock hazards.
Mount the module onto a standard 35mm symmetrical DIN rail inside a dry, clean industrial enclosure meeting IP54 or higher requirements.
Verify that the rotary switches for Station Number and Baud Rate are set to match the configurations defined in your PLC's network master parameters.
Wire the CC-Link communication bus using dedicated shielded twisted-pair cabling. Ground the SLD and FG terminals to an appropriate class-D earth ground.
Connect the field outputs and common lines. Confirm terminal screw tightness to prevent high resistance connections or intermittent signal drops under thermal cycling.
Глобална експресна доставка
Връщания и гаранция
Поръчките се обработват и доставят от понеделник до петък (с изключение на официалните празници).
За пълна информация относно допустимост, такси за презареждане и международни връщания, моля, разгледайте нашия официален Политика за възстановяване и връщане .
| Country of origin |
Съединени щати
|
Тази статия обяснява как интегрираните електрически задвижвания, като серията e-Actuator на SMC, трансформират индустриалното управление на движението, като заменят традиционните пневматични и...
Тази статия обяснява как PLC системите изпълняват основни математически операции като събиране, изваждане, умножение, деление, модуло и степенуване в индустриалната автоматизация. Показва как тези...
Статията обяснява няколко усъвършенствани булеви логически функции, използвани в програмирането на PLC, извън основните операции AND, OR и NOT. Тя разглежда как инструменти като таблици на...
Булевата логика е основата на всяка програма за PLC. От прости машинни управления до сложни индустриални автоматизационни системи, логическите врати определят как контролерите реагират на променящите...
Индустриалните защитни стени играят ключова роля в киберсигурността на OT, като защитават мрежите PLC, DCS и SCADA чрез сегментация, контрол на входящия/изходящия трафик и интеграция на IDS/IPS в...
Съвременните роботизирани захвати се развиват отвъд традиционните механични челюсти. От системи с лепкави повърхности, вдъхновени от геконите, и меки захвати за хранителни продукти до инструменти за...
