Hersteller: Honeywell
Produkt-Nr.: TC-FPCXX2
Herkunftsland:Vereinigte Staaten
Produkttyp: PLC Power Supply Modules
Zahlung: T/T, Western Union
Gewicht: 2100g
Abmessungen: 11.2 cm x 14.5 cm x 14.0 cm
Versandhafen: Xiamen
Garantie: 12 Monate
Providing regulated operating power to local rack configurations, the Honeywell TC-FPCXX2 serves as a high-reliability chassis power supply module engineered for industrial process control environments. This module accepts selectable AC input ranges to deliver a maximum continuous output of 70 W at 60 degC, ensuring stable voltage distribution to adjacent controller and I/O modules. The unit incorporates integrated thermal protection and structural overcurrent safeguarding via an onboard soldered internal fuse to maintain system integrity under transient fault conditions.
| Parameter | Specification Value |
|---|---|
| Manufacturer | Honeywell |
| Model Reference | TC-FPCXX2 |
| Input Voltage Range | 85-132 VAC or 170-265 VAC (User-selectable via slide switch) |
| Line Frequency Range | 47-63 Hz |
| Maximum Output Power | 70 W at 60 degC |
| Overcurrent Protection | Non-replaceable soldered-in input fuse |
| Module Dimensions (W x D x H) | 11.2 cm x 14.5 cm x 14.0 cm (4.41 in x 5.71 in x 5.51 in) |
| Net Module Weight | 1.1 kg (2.43 lbs) |
| Shipping Weight (Calculated) | 2.1 kg (4.63 lbs) |
The TC-FPCXX2 is functionally interchangeable with older Honeywell legacy chassis power options, but caution must be exercised regarding mounting pitch and backplane connector alignment. While standard C200 controllers utilize similar configurations, always verify that the chassis slot keying matches the deep-recessed connector housing on the back of this module before attempting hot insertion.
Because this power supply uses a non-replaceable, soldered-in input fuse, external overcurrent protection (such as an inline terminal block fuse or miniature circuit breaker rated at 5 A or 10 A depending on input configuration) is highly recommended. If an internal component fault triggers the soldered fuse, the entire unit must be serviced or replaced; external fusing mitigates transient line surges from rendering the module permanently inoperable on site.
Before applying power, verify the position of the dual-voltage slide selector switch located on the unit. Energizing a module configured for 115 VAC with a 230 VAC supply line will cause immediate, catastrophic damage to the input varistors and internal circuitry, voiding standard field warranties.
CRITICAL WARNING
Isolate and lock out all incoming AC power lines before mounting or sliding the power module into the chassis. Do not touch terminal screws or the rear connector interface while the main bus is energized. Failure to comply can result in severe electrical shock, equipment destruction, or unexpected process downtime.
Locate the input voltage selector switch on the side or rear of the module. Confirm its setting matches your local utility supply level (115 VAC or 230 VAC nominal).
Align the module with the guide rails of the designated left-most power supply slot in the chassis.
Slide the module firmly backward until the rear interface connector seats fully into the backplane socket. Hand-tighten the integrated retaining screws to secure the unit structurally.
Connect the external, de-energized AC supply wiring to the input terminals, ensuring the protective earth ground wire is established first.
Globaler Expressversand
Rückgaben & Garantie
Bestellungen werden Montag bis Freitag bearbeitet und geliefert (außer an Feiertagen).
Für vollständige Anspruchsvoraussetzungen, Wiedereinlagerungsgebühren und internationale Rückgabedetails, sehen Sie bitte unsere offizielle Seite ein Rückerstattungs- & Rückgabebedingungen .
| Country of origin |
Vereinigte Staaten
|
This article explains how integrated electric actuators, such as SMC’s e-Actuator series, are transforming industrial motion control by replacing traditional pneumatic and hydraulic systems. It...
Dieser Artikel erklärt, wie SPS-Systeme grundlegende mathematische Operationen wie Addition, Subtraktion, Multiplikation, Division, Modulo und Exponentiation in der industriellen Automatisierung...
Der Artikel erklärt mehrere erweiterte Boolesche Logikfunktionen, die in der SPS-Programmierung über die grundlegenden AND-, OR- und NOT-Operationen hinaus verwendet werden. Er behandelt, wie...
Boolesche Logik ist die Grundlage jedes SPS-Programms. Von einfachen Maschinensteuerungen bis hin zu komplexen industriellen Automatisierungssystemen bestimmen Logikgatter, wie Steuerungen auf sich...
Industrielle Firewalls spielen eine entscheidende Rolle in der OT-Cybersicherheit, indem sie SPS-, DCS- und SCADA-Netzwerke durch Segmentierung, Ein- und Ausgangskontrolle sowie IDS/IPS-Integration...
Moderne robotische Greifer entwickeln sich über traditionelle mechanische Greifbacken hinaus. Von gecko-inspirierten Haftsystemen und weichen, lebensmittelechten Greifern bis hin zu KI-gestützten...
