Isolateurs d'alimentation courant transparents protocole HART ACT20X-HAI-SAO-S Weidmüller 8965430000

Product Overview

The Weidmuller 8965430000 (ACT20X-HAI-SAO-S) is a precision-engineered single-channel HART-protocol transparent current-supply isolator. Designed for critical signal conditioning in hazardous areas, this module provides an essential barrier between 4 to 20 mA field transmitters and the control system (DCS/PLC). The 8965430000 specializes in "HART transparency," allowing digital diagnostic and configuration data to pass through the analog loop without interference. By utilizing galvanic isolation, it eliminates ground loops and protects the control infrastructure from electrical transients. Its ultra-high accuracy (< 0.1% span) and rapid 5 ms response time make it a standard choice for high-availability process plants, including refineries and chemical processing facilities.

Technical Configuration

The ACT20X-HAI-SAO-S is a high-performance single-channel variant within the ACT20X family, housed in a space-efficient 22.5 mm DIN-rail mounting enclosure. It features a versatile voltage supply range (19.2 to 31.2 VDC) and utilizes screw connections for secure, vibration-resistant wiring.

Unlike basic isolators, this unit is fully software-configurable via the FDT/DTM interface. This allows engineers to monitor and set alarm thresholds for four specific fault conditions: signal limit violations, input line interruptions, loss of supply voltage, and internal device errors. The integrated relay output provides a hardwired alarm contact capable of switching up to 125 VAC, ensuring that critical faults are communicated to the safety system even if the primary analog signal is compromised. Its low power consumption (<= 1.0 W) reduces the heat load within crowded marshalling cabinets.

Technical Specifications

Technical FAQs

Q1: What is the benefit of the 5 ms step response time in this isolator?A1: A 5 ms response time ensures that the isolator adds negligible delay to the control loop. This is critical for high-speed pressure or flow control applications where even millisecond delays can lead to process instability or oscillations.

Q2: How does HART transparency assist with maintenance?A2: It allows technicians to use a HART handheld communicator or asset management software (like AMS or PRM) to calibrate field transmitters directly through the isolator. You do not need to bypass the module to access the transmitter's digital data.

Q3: Can the alarm relay be used for more than just "Line Interruption"?A3: Yes. Through the FDT/DTM software, you can configure the relay to trigger based on "Signal limit exceeded" (e.g., if the mA goes above 21 mA or below 3.8 mA), as well as internal device errors or power loss.

Engineering & Installation Guide

• HART Loop Resistance: Ensure that the total loop resistance (including the transmitter, field wiring, and the isolator's internal resistance) remains within the transmitter's driving capacity. A 250 Ohm resistor is typically required for HART communication, and the ACT20X-HAI-SAO-S is designed to accommodate this while maintaining signal integrity.

• Grounding and Shielding: For maximum accuracy (< 0.1% span), use twisted-pair shielded cables for the 4 to 20 mA signal. Connect the shield at a single point (usually the DCS cabinet earth) to prevent ground loops that could induce noise into the high-precision analog measurement.

• Firmware and DTM Sync: Always use the latest DTM (Device Type Manager) version from Weidmuller's WI-Manager suite when configuring the 8965430000. This ensures that all diagnostic features and alarm parameters are correctly mapped and accessible during commissioning.

Engineering Advantages

The 8965430000 is distinguished by its exceptional thermal stability (< 0.01% of span per deg C), making it ideal for cabinets located in non-climate-controlled environments. Its single-channel design offers modularity; a single loop failure or maintenance requirement only affects one process variable, enhancing the overall "Fault Tolerance" of the I/O node. Furthermore, the 1.0W low-power architecture significantly extends the MTBF (Mean Time Between Failures) of the device by minimizing internal component stress caused by heat, which is a primary concern in 24/7 continuous process industries.