Bently Nevada 330101-00-19-10-02-05 3300 XL 8 mm Proximity Probe

Description

The Bently Nevada 330101-00-19-10-02-05 is a high-performance 8 mm proximity probe engineered for non-contact shaft vibration and displacement measurements in critical rotating machinery. As a core sensing component of the 3300 XL Proximity Transducer System, this probe is specifically built with a 3/8-24 UNF threaded body and no protective armor (330101 base configuration), making it ideal for standard industrial installations where physical external armor is not required. This unique configuration features an unthreaded length of 0.0 inches (0 mm) paired with an overall case length of 1.9 inches (48 mm) (option codes 00 and 19 respectively), making it optimal for flush-mount or shallow bearing housing installations. It has a total cable length of 1.0 meter (3.3 feet) (option 10) and is equipped with a standard cable and a miniature coaxial ClickLoc connector (option 02) without a connector protector. Fully certified under agency option 05, this probe features CSA, ATEX, and IECEx approvals for safe deployment in hazardous industrial areas. Utilizing the eddy-current operating principle, it provides highly precise non-contact displacement monitoring to protect high-speed machinery from catastrophic failures.

Features

• Precision 8 mm tip diameter proximity probe optimized for high-accuracy, non-contact eddy-current displacement measurements.
• Corrosion-resistant stainless steel probe body and polyphenylene sulfide (PPS) tip construction designed to withstand harsh machine environments.
• 3/8-24 UNF threaded body without armor casing (330101 base configuration) for standard mechanical mounting.
• 0.0 inches unthreaded length (00 option) and 1.9 inches overall case length (19 option) to suit compact mechanical clearances.
• 1.0 meter overall total length (10 option) designed to connect seamlessly with 3300 XL standard extension cables in a 5-meter or 9-meter transducer system.
• Miniature ClickLoc coaxial connector (02 option) on standard cable provides clean signal connection with low insertion loss.
• Hazardous area approved (05 option) with CSA, ATEX, and IECEx certifications for safe operation in explosive atmospheres.

Applications

• Steam and gas turbine shaft vibration and axial position monitoring.
• Compressor and pump rotor displacement and thrust measurement.
• Continuous machinery protection in petrochemical plants, oil refineries, and power generation facilities.
• Permanent installations in bearing housings and machine casings for critical asset condition monitoring.

Ordering Information

Technical Specifications

Installation Guidelines

• Mount the probe with the appropriate probe gap (nominally -9 Vdc or approximately 1.27 mm / 50 mils) corresponding to system calibration over the linear range.
• Ensure that external cables are routed with proper shielding and grounding practices to eliminate electromagnetic interference (EMI) in proximity probe vibration installations.
• Observe a maximum thread engagement limit of 0.563 inches for the 3/8-24 UNF mounting thread to avoid binding or mechanical strain during installation.
• Tighten the ClickLoc coaxial connectors finger-tight. Avoid using heavy tools or pliers unless mating with older non-XL stainless steel connectors.
• Prevent exposing the probe sealing mechanism to temperatures below -34 degC (-30 degF) to preserve the integrity of the internal Viton O-ring.

Compliance and Certifications

• CSA: Intrinsically Safe and Non-Incendive ratings for Class I, Division 1 and Division 2 hazardous locations when installed per drawing 141092 or 140979.
• ATEX/IECEx: Certified Ex ia IIC T5...T1 Ga for intrinsically safe applications (EPL Ga and Gc) and Ex ec IIC T5...T1 Gc for non-sparking/increased safety installations.
• CE Mark: Fully compliant with applicable European Union directives for industrial electronic hardware.