Produsen: Mitsubishi Electric
Nomor Produk: FR-F840-01160-2-60
Negara asal:Amerika Serikat
Jenis Produk: Variable Frequency Drives
Pembayaran: T/T, Western Union
Berat: 41000g
Pelabuhan pengiriman: Xiamen
Garansi: 12 bulan
Engineered to optimize centrifugal pump and fan efficiency across demanding industrial networks, the Mitsubishi Electric FR-F840-01160-2-60 Variable Frequency Drive delivers precision speed control within the high-performance FR-F800 Series. This unit features advanced energy-saving algorithms and robust hardware tailored for hostile atmospheres. The FR-F840-01160-2-60 carries a heavy-duty design rating of 55 kW, utilizing specialized protective circuit board coatings to extend its operational lifespan in corrosive or humid environments.
| Parameter | Specification Value |
|---|---|
| Manufacturer | Mitsubishi Electric |
| Model Code | FR-F840-01160-2-60 |
| Series Name | FR-F800 |
| Applicable Motor Capacity | 55 kW |
| Rated Output Current | 116 A |
| Output Rated Capacity | 88 kVA |
| Input Voltage Phase / Freq | Three-phase 380 to 500 V AC, 50 Hz / 60 Hz |
| Voltage Fluctuation Range | 323 to 550 V AC, 50 Hz / 60 Hz |
| Frequency Fluctuation Range | +/- 5 percent |
| Power Supply Capacity | 107 kVA |
| IP Rating / Enclosure | IP00 (Open Type, JEM1030) |
| Cooling System | Forced Air Cooling |
| Country of Origin | Japan |
| Unit Net Weight | 41.0 kg |
| Shipping Weight (Calculated) | 47.0 kg |
| Terminal Designation | Functional Assignment / Circuit Role |
|---|---|
| R/L1, S/L2, T/L3 | Three-phase AC power input connections |
| U, V, W | Three-phase variable frequency output to AC induction motor |
| P/+, PR | DC Bus positive / connection to dynamic braking resistor |
| P/+, N/- | DC Bus common link connection for regenerative converter configurations |
| Earth / Ground (PE) | Chassis grounding terminal for electrical noise safety compliance |
Standard units in this catalog range carry a "-1" suffix for baseline industrial environments. The FR-F840-01160-2-60 features a "-2" region designator (equivalent to standard CA functional specification with embedded European/Chinese EMC filter standards) combined with the protective "-60" suffix. It is directly backwards-compatible in mechanical sizing with standard FR-F740 models of equivalent physical footprint, though parameters must be translated via FR Configurator2 software prior to operational start.
Because this unit is an IP00 open-type chassis, it is susceptible to direct environmental ingress if left unhoused. Mounting inside an IP54 or higher rated MCC panel is required. The drive dissipates approximately 1.5 kW of heat under full-load operation. Ensure your panel's thermal engineering supports forced ventilation calculation rates of at least 250 cubic meters per hour to avoid over-temperature trips.
Keep analog control lines completely separated from high-energy output cables. Ground shielding for terminal connections must terminate at the grounding plate immediately adjacent to the VFD chassis. Do not short the SD terminal (control common) to the safety earth (PE) ground, as this initiates ground loops that cause noise-induced controller resetting.
De-energize all primary supply lines before removing the terminal block covers. Allow a minimum of 10 minutes for internal DC bus capacitors to fully discharge. Always verify that voltage between terminals P/+ and N/- is below 50 V DC with a calibrated voltmeter before executing any physical wiring or maintenance steps.
Mount the chassis vertically on an unpainted, flat metal backplate to ensure continuous electrical ground continuity. Maintain 100 mm clearances above and below the cooling vents.
Route AC input (R/L1, S/L2, T/L3) and output motor connections (U, V, W) through separate metallic conduits to prevent cross-talk and high-frequency interference.
Ground all control shields directly at the cable clamp. Terminate control signals on separate paths from power wiring. Avoid connecting terminal SD to structural PE ground.
Pengiriman Ekspres Global
Pengembalian & Garansi
Pesanan diproses dan dikirimkan Senin-Jumat (tidak termasuk hari libur nasional).
Untuk kelayakan penuh, biaya pengisian ulang, dan detail pengembalian internasional, silakan lihat resmi kami Kebijakan Pengembalian & Pengembalian Dana .
| Country of origin |
Amerika Serikat
|
Artikel ini menjelaskan bagaimana aktuator listrik terintegrasi, seperti seri e-Actuator dari SMC, mengubah kontrol gerak industri dengan menggantikan sistem pneumatik dan hidrolik tradisional....
Artikel ini menjelaskan bagaimana sistem PLC melakukan operasi matematika inti seperti penjumlahan, pengurangan, perkalian, pembagian, modulo, dan perpangkatan dalam otomasi industri. Artikel ini...
Artikel ini menjelaskan beberapa fungsi logika Boolean lanjutan yang digunakan dalam pemrograman PLC selain operasi dasar AND, OR, dan NOT. Artikel ini membahas bagaimana alat seperti tabel...
Logika Boolean adalah dasar dari setiap program PLC. Dari kontrol mesin sederhana hingga sistem otomasi industri yang kompleks, gerbang logika menentukan bagaimana pengendali merespons perubahan...
Firewall industri memainkan peran penting dalam keamanan siber OT, melindungi jaringan PLC, DCS, dan SCADA melalui segmentasi, kontrol masuk/keluar, dan integrasi IDS/IPS yang sesuai dengan prinsip...
Gripper robot modern berkembang melampaui rahang mekanis tradisional. Mulai dari sistem adhesif yang terinspirasi oleh cicak dan gripper lembut yang aman untuk makanan hingga alat gudang bertenaga...
