Manufacturer: BECKHOFF
Product No.: IP1502-B400
Country of origin:Niemcy
Product Type: Fieldbus Box Modules
Payment: T/T, Western Union
Weight: 2000g
Dimensions: 18.0 x 6.0 x 5.0 cm
Shipping port: Xiamen
Warranty: 12 months
Processing high-frequency pulse trains directly at the machine level, the Beckhoff IP1502-B400 Fieldbus Box serves as a decentralized 2-channel up/down counter module designed for Interbus networks. This rugged IP67-rated device enables direct field installation without a control cabinet, capturing rapid pulse sequences from rotary encoders, flow meters, and proximity sensors with high precision.
| Parameter | Specification Value |
|---|---|
| Manufacturer | Beckhoff Automation |
| Model Number | IP1502-B400 |
| Fieldbus Interface | Interbus |
| Number of Channels | 2 independent counters |
| Maximum Input Frequency | 100 kHz |
| Nominal Operating Voltage | 24 V DC (-15% / +20%) |
| Sensor Supply Voltage | 24 V DC, derived from auxiliary power supply |
| Connection Type | M12 screw connectors (5-pin) |
| Ingress Protection Rating | IP67 (when all connectors are mated or sealed) |
| Operating Temperature | 0 degC to +55 degC |
| Storage Temperature | -25 degC to +85 degC |
| Country of Origin | Germany |
| Shipping Weight (Calculated) | 0.35 kg |
| Package Dimensions (Calculated) | 18.0 x 6.0 x 5.0 cm |
| M12 Connector Pin | Interbus IN Function | Interbus OUT Function | Counter Input Function |
|---|---|---|---|
| Pin 1 | DO (Data Out) | DO (Data Out) | +24 V DC Sensor Supply |
| Pin 2 | /DO (Data Out Inverted) | /DO (Data Out Inverted) | Input B (Direction / Pulse) |
| Pin 3 | DI (Data In) | DI (Data In) | GND (Sensor Ground) |
| Pin 4 | /DI (Data In Inverted) | /DI (Data In Inverted) | Input A (Count / Gate) |
| Pin 5 | GND (Signal Ground) | GND (Signal Ground) | PE (Functional Earth) |
The IP1502-B400 is specifically designed for Interbus installations using the B400 protocol profile. If migrating to EtherCAT or PROFIBUS networks, this module must be replaced with the EP1518 or IP1502-B310/B510 variants. Ensure that your Interbus master configuration file (CMD software or equivalent) is updated with the correct ID code and length code matching the IP1502-B400 to prevent bus cycle mismatch errors.
When operating at the maximum 100 kHz input frequency, signal attenuation over long cable runs can lead to missed pulses. It is highly recommended to limit sensor cable lengths to under 10 meters and use low-capacitance, shielded twisted-pair cabling. In high-vibration environments, ensure the M12 connectors are torqued to the manufacturer-specified 0.6 Nm to maintain the IP67 seal and prevent intermittent contact.
Always ground the module locally using the integrated grounding lug or by mounting it directly to a grounded, unpainted metallic machine frame. Proper grounding is critical for suppressing high-frequency electromagnetic interference (EMI) generated by nearby variable frequency drives (VFDs) and servo motors, which can otherwise corrupt the high-speed counter registers.
De-energize all power sources (both logic supply and auxiliary sensor power) before mounting, connecting, or disconnecting the module. Failure to do so can cause permanent damage to the internal Interbus transceiver circuitry and result in unpredictable machine behavior.
Mount the Fieldbus Box securely to a flat, vibration-resistant surface using two M4 screws through the integrated mounting holes.
Connect the Interbus incoming and outgoing cables to the corresponding M12 ports, ensuring correct keyway alignment before tightening.
Wire the counter inputs using shielded M12 sensor cables. Terminate the shield at both the sensor housing and the module's PE pin.
Apply 24 V DC auxiliary power, verify that the status LEDs indicate active communication, and perform a register test via the Interbus master.
Globalna ekspresowa wysyłka
Zwroty i gwarancja
Zamówienia są przetwarzane i dostarczane od poniedziałku do piątku (z wyłączeniem dni świątecznych).
Aby poznać pełne warunki kwalifikowalności, opłaty za przyjęcie towaru z powrotem oraz szczegóły dotyczące zwrotów międzynarodowych, prosimy zapoznać się z naszym oficjalnym Polityka zwrotów i zwrotu pieniędzy .
| Country of origin |
Niemcy
|
This article explains how integrated electric actuators, such as SMC’s e-Actuator series, are transforming industrial motion control by replacing traditional pneumatic and hydraulic systems. It...
This article explains how PLC systems perform core mathematical operations such as addition, subtraction, multiplication, division, modulo, and exponentiation within industrial automation. It shows...
The article explains several advanced Boolean logic functions used in PLC programming beyond basic AND, OR, and NOT operations. It covers how tools like truth tables, multiplexers, pulse generators,...
Boolean logic is the foundation of every PLC program. From simple machine controls to complex industrial automation systems, logic gates determine how controllers respond to changing inputs and...
Industrial firewalls play a critical role in OT cybersecurity, protecting PLC, DCS, and SCADA networks through segmentation, ingress/egress control, and IDS/IPS integration aligned with IEC 62443...
Modern robotic grippers are evolving beyond traditional mechanical jaws. From gecko-inspired adhesive systems and soft food-grade grippers to AI-powered warehouse tools, advanced gripping...
