Option 00 (0.0 in unthreaded length), Option 15 (1.5 in overall case length), and Option 02 (miniature coaxial ClickLoc connector, standard cable) specify this 3300 XL 11 mm proximity probe configuration - 330701-00-15-10-02-05. Operating as a non-contact eddy-current displacement sensor, it measures dynamic shaft vibration and static position on rotating machinery. The unarmored 1/2-20 UNF threaded steel body mounts directly in threaded machine casings or brackets to capture shaft movement with high precision.
This transducer component is used in 3300 XL 11 mm monitoring systems, pairing with a 330730 extension cable to match the calibration requirements of a 330780 Proximitor sensor. By combining a 1.0 m probe with a 4.0 m extension cable, the system achieves a total electrical length of 5.0 m. The standard ClickLoc coaxial connectors maintain low-resistance signal transfer, while the integrated Locknut with pre-drilled safety wire holes aids mechanical retention under vibration.
| Option | Code on This SKU | Description |
|---|---|---|
| Orderable Part Number | 330701-00-15-10-02-05 | 3300 XL 11 mm proximity probe, 1/2-20 UNF thread, standard mount, without armor |
| A: Unthreaded Length Option | 00 | 0.0 in (0 mm) unthreaded length |
| B: Overall Case Length Option | 15 | 1.5 in (38 mm) overall case length |
| C: Total Length Option | 10 | 1.0 meter (3.3 feet) total probe length |
| D: Connector and Cable-Type Option | 02 | Miniature coaxial ClickLoc connector, standard cable |
| E: Agency Approval Option | 05 | Multiple Approvals (CSA, ATEX, IECEx) |
| Parameter | Specification Value |
|---|---|
| Manufacturer | Bently Nevada (Baker Hughes) |
| Model / Series | 3300 XL 11 mm Transducer System |
| Linear Range | 4.0 mm (160 mils), beginning at 0.5 mm (20 mils) from target (from 0.5 to 4.5 mm) |
| Scale Factor | 3.94 V/mm (100 mV/mil) with 10% tolerance (including interchangeability error) |
| Recommended Gap | 2.5 mm (100 mils) |
| Frequency Response | 0 to 8 kHz (+0, -3 dB typical) with up to 305 meters of field wiring |
| Target Calibration | AISI 4140 steel target (flat surface, 30.5 mm/1.2 in minimum diameter recommended) |
| Probe dc Resistance | 5.9 ohms +/- 0.5 ohms (center conductor to outer conductor for 1.0 m probe) |
| Probe Tip Material | Polyphenylene sulfide (PPS) |
| Probe Case Material | AISI 304 stainless steel (SST) |
| Probe Cable | 75 ohm triaxial, fluoroethylene propylene (FEP) insulated |
| Connector Material | Gold-plated brass ClickLoc coaxial connector |
| Tensile Strength | 330 N (75 lb) probe case to probe lead maximum rated pull strength |
| Probe Case Torque | 45.2 N-m (400 in-lb) maximum rated torque; 15.2 N-m (133 in-lb) recommended torque |
| Operating Temperature (Probe) | -52 degC to +177 degC (-62 degF to +351 degF) |
Positioning the probe requires establishing the standard 2.5 mm (100 mils) gap using a voltmeter to measure the corresponding -10 Vdc bias output. Standard mount 1/2-20 UNF threaded probes must be locked in place using the supplied locknut. The locknut has pre-drilled holes for safety wire to prevent loose rotation. The minimum bend radius for the probe cable is 25.4 mm (1.0 inch) to protect the internal triaxial conductors. Hand-tighten coaxial ClickLoc connectors; do not exceed 0.565 N-m (5 in-lb) of torque if utilizing mechanical tools. Exposing the probe to temperatures below -34 degC (-30 degF) may cause premature failure of the pressure seal.
Approved under Option 05 (Multiple Approvals) for hazardous areas, featuring certifications from CSA, ATEX, and IECEx. Under intrinsically safe installations (Ex ia IIC T4/T5 Ga), install the system with approved zener barriers or galvanic isolators per Bently Nevada drawing 141092. For non-incendive installations (Ex nA/ec IIC T4/T5 Gc), refer to drawing 140979. The product complies with European EMC Directive 2014/30/EU, EN 61000-6-2 (Industrial Immunity), EN 61000-6-4 (Industrial Emissions), and RoHS Directive 2011/65/EU.
Global Express Shipping
Returns & Warranty
Manufacturer: Bently Nevada
Product No.: 330701-00-15-10-02-05
Country of origin:United States
Product Type: 3300 XL 11 mm Proximity Probe
Barcode: 8537101190
Payment: T/T, Western Union
Weight: 180g
Dimensions: 50 mm x 100 mm x 100 mm (H x W x D)
Shipping port: Xiamen
Warranty: 12 months
Option 00 (0.0 in unthreaded length), Option 15 (1.5 in overall case length), and Option 02 (miniature coaxial ClickLoc connector, standard cable) specify this 3300 XL 11 mm proximity probe configuration - 330701-00-15-10-02-05. Operating as a non-contact eddy-current displacement sensor, it measures dynamic shaft vibration and static position on rotating machinery. The unarmored 1/2-20 UNF threaded steel body mounts directly in threaded machine casings or brackets to capture shaft movement with high precision.
This transducer component is used in 3300 XL 11 mm monitoring systems, pairing with a 330730 extension cable to match the calibration requirements of a 330780 Proximitor sensor. By combining a 1.0 m probe with a 4.0 m extension cable, the system achieves a total electrical length of 5.0 m. The standard ClickLoc coaxial connectors maintain low-resistance signal transfer, while the integrated Locknut with pre-drilled safety wire holes aids mechanical retention under vibration.
| Option | Code on This SKU | Description |
|---|---|---|
| Orderable Part Number | 330701-00-15-10-02-05 | 3300 XL 11 mm proximity probe, 1/2-20 UNF thread, standard mount, without armor |
| A: Unthreaded Length Option | 00 | 0.0 in (0 mm) unthreaded length |
| B: Overall Case Length Option | 15 | 1.5 in (38 mm) overall case length |
| C: Total Length Option | 10 | 1.0 meter (3.3 feet) total probe length |
| D: Connector and Cable-Type Option | 02 | Miniature coaxial ClickLoc connector, standard cable |
| E: Agency Approval Option | 05 | Multiple Approvals (CSA, ATEX, IECEx) |
| Parameter | Specification Value |
|---|---|
| Manufacturer | Bently Nevada (Baker Hughes) |
| Model / Series | 3300 XL 11 mm Transducer System |
| Linear Range | 4.0 mm (160 mils), beginning at 0.5 mm (20 mils) from target (from 0.5 to 4.5 mm) |
| Scale Factor | 3.94 V/mm (100 mV/mil) with 10% tolerance (including interchangeability error) |
| Recommended Gap | 2.5 mm (100 mils) |
| Frequency Response | 0 to 8 kHz (+0, -3 dB typical) with up to 305 meters of field wiring |
| Target Calibration | AISI 4140 steel target (flat surface, 30.5 mm/1.2 in minimum diameter recommended) |
| Probe dc Resistance | 5.9 ohms +/- 0.5 ohms (center conductor to outer conductor for 1.0 m probe) |
| Probe Tip Material | Polyphenylene sulfide (PPS) |
| Probe Case Material | AISI 304 stainless steel (SST) |
| Probe Cable | 75 ohm triaxial, fluoroethylene propylene (FEP) insulated |
| Connector Material | Gold-plated brass ClickLoc coaxial connector |
| Tensile Strength | 330 N (75 lb) probe case to probe lead maximum rated pull strength |
| Probe Case Torque | 45.2 N-m (400 in-lb) maximum rated torque; 15.2 N-m (133 in-lb) recommended torque |
| Operating Temperature (Probe) | -52 degC to +177 degC (-62 degF to +351 degF) |
Positioning the probe requires establishing the standard 2.5 mm (100 mils) gap using a voltmeter to measure the corresponding -10 Vdc bias output. Standard mount 1/2-20 UNF threaded probes must be locked in place using the supplied locknut. The locknut has pre-drilled holes for safety wire to prevent loose rotation. The minimum bend radius for the probe cable is 25.4 mm (1.0 inch) to protect the internal triaxial conductors. Hand-tighten coaxial ClickLoc connectors; do not exceed 0.565 N-m (5 in-lb) of torque if utilizing mechanical tools. Exposing the probe to temperatures below -34 degC (-30 degF) may cause premature failure of the pressure seal.
Approved under Option 05 (Multiple Approvals) for hazardous areas, featuring certifications from CSA, ATEX, and IECEx. Under intrinsically safe installations (Ex ia IIC T4/T5 Ga), install the system with approved zener barriers or galvanic isolators per Bently Nevada drawing 141092. For non-incendive installations (Ex nA/ec IIC T4/T5 Gc), refer to drawing 140979. The product complies with European EMC Directive 2014/30/EU, EN 61000-6-2 (Industrial Immunity), EN 61000-6-4 (Industrial Emissions), and RoHS Directive 2011/65/EU.
Global Express Shipping
Returns & Warranty
Orders are processed and delivered Monday-Friday (excluding public holidays).
For full eligibility, restocking fees, and international return details, please view our official Refund & Return Policy .
| Country of origin |
United States
|
Replacing a 1756-L73 does not automatically mean upgrading its firmware. This guide compares v19.013, v21.011 and v31.011, focusing on project compatibility, HMI communications, legacy networks and...
Implement a 3-SPST switch XOR light circuit in LogixPro or RSLogix 500 using an internal relay bit. Includes truth tables, boolean equations, and verified.
Integrate Allen-Bradley CompactLogix, Caterpillar ATS, and generators into DeltaV DCS over Modbus RTU. Covers ProSoft MVI69-MCM, Miille DIN266 gateways.
ONS instruction fires but the OTE coil never latches in Studio 5000 because the one-shot is only true for one scan. Use OTL/OTU or seal-in logic instead.
Configure Allen-Bradley Kinetix 5500 servo drives on EtherNet/IP. Covers CIP Sync, IEEE 1588 V2 timing, Stratix selection, DLR topology, and HMI.
A moving-average filter is the sliding-window smoother most instrument engineers drop into DCS and PLC analog paths. Here is how the window works, how N and sample time set lag, and when a...
