Engineered for high-performance dynamic positioning in space-restricted industrial environments, the Mitsubishi Electric HC-UF43K is a flat-type, low-inertia AC servo motor. This unit integrates into the MELSERVO system architecture, offering precise angular velocity and torque control. The low-profile mechanical design of the HC-UF43K makes it an ideal choice for machinery requiring high torque density without increasing the physical footprint. Equipped with a keyed shaft configuration, this motor ensures slip-free torque transmission during rapid acceleration and deceleration cycles.
| Parameter | Value |
|---|---|
| Manufacturer | Mitsubishi Electric |
| Model Number | HC-UF43K |
| Motor Series | HC-UF Series (Flat Type) |
| Rated Output | 0.4 kW (400 W) |
| Rated Speed | 3000 r/min |
| Shaft Type | With keyway (Includes key) |
| Motor Mass | 1.7 kg (3.7 lbs) |
| Shipping Weight (Calculated) | 2.7 kg (5.95 lbs) |
The HC-UF43K AC servo motor is designed for native integration with MR-J2S series servo amplifiers (specifically the MR-J2S-40A and MR-J2S-40B modules). When upgrading legacy motion systems, verify that the amplifier firmware is compatible with HC series motors. Note that physical replacements must maintain exact mounting dimensions, as flat-type motors feature a distinct bolt circle diameter compared to standard cylindrical models.
Because flat-profile motors have a reduced external surface area, heat dissipation is highly dependent on conductive cooling through the mounting face. Ensure the motor is bolted directly to a clean, unpainted metal surface (such as an aluminum frame) of sufficient mass to serve as an effective heat sink. Additionally, avoid exceeding the maximum radial and axial load limits on the shaft, as flat-motor bearings are sensitive to overhung loads which can cause premature wear and encoder alignment drift.
To avoid high-frequency noise interference in the encoder signal line, always use double-shielded twisted-pair cabling for the encoder feedback loop. Ground the cable shield at the servo amplifier chassis side only. If experiencing "AL.16" or "AL.20" fault codes on your MR-J2S drive, check the integrity of the encoder connector plug pins and ensure no moisture has entered the motor terminal housing during installation.
Global Express Shipping
Returns & Warranty
Manufacturer: Mitsubishi Electric
Product No.: HC-UF43K
Country of origin:United States
Product Type: AC Servo Motors
Payment: T/T, Western Union
Weight: 2700g
Shipping port: Xiamen
Warranty: 12 months
Engineered for high-performance dynamic positioning in space-restricted industrial environments, the Mitsubishi Electric HC-UF43K is a flat-type, low-inertia AC servo motor. This unit integrates into the MELSERVO system architecture, offering precise angular velocity and torque control. The low-profile mechanical design of the HC-UF43K makes it an ideal choice for machinery requiring high torque density without increasing the physical footprint. Equipped with a keyed shaft configuration, this motor ensures slip-free torque transmission during rapid acceleration and deceleration cycles.
| Parameter | Value |
|---|---|
| Manufacturer | Mitsubishi Electric |
| Model Number | HC-UF43K |
| Motor Series | HC-UF Series (Flat Type) |
| Rated Output | 0.4 kW (400 W) |
| Rated Speed | 3000 r/min |
| Shaft Type | With keyway (Includes key) |
| Motor Mass | 1.7 kg (3.7 lbs) |
| Shipping Weight (Calculated) | 2.7 kg (5.95 lbs) |
The HC-UF43K AC servo motor is designed for native integration with MR-J2S series servo amplifiers (specifically the MR-J2S-40A and MR-J2S-40B modules). When upgrading legacy motion systems, verify that the amplifier firmware is compatible with HC series motors. Note that physical replacements must maintain exact mounting dimensions, as flat-type motors feature a distinct bolt circle diameter compared to standard cylindrical models.
Because flat-profile motors have a reduced external surface area, heat dissipation is highly dependent on conductive cooling through the mounting face. Ensure the motor is bolted directly to a clean, unpainted metal surface (such as an aluminum frame) of sufficient mass to serve as an effective heat sink. Additionally, avoid exceeding the maximum radial and axial load limits on the shaft, as flat-motor bearings are sensitive to overhung loads which can cause premature wear and encoder alignment drift.
To avoid high-frequency noise interference in the encoder signal line, always use double-shielded twisted-pair cabling for the encoder feedback loop. Ground the cable shield at the servo amplifier chassis side only. If experiencing "AL.16" or "AL.20" fault codes on your MR-J2S drive, check the integrity of the encoder connector plug pins and ensure no moisture has entered the motor terminal housing during installation.
Global Express Shipping
Returns & Warranty
Orders are processed and delivered Monday-Friday (excluding public holidays).
For full eligibility, restocking fees, and international return details, please view our official Refund & Return Policy .
| Country of origin |
United States
|
Implement a 3-SPST switch XOR light circuit in LogixPro or RSLogix 500 using an internal relay bit. Includes truth tables, boolean equations, and verified.
Integrate Allen-Bradley CompactLogix, Caterpillar ATS, and generators into DeltaV DCS over Modbus RTU. Covers ProSoft MVI69-MCM, Miille DIN266 gateways.
ONS instruction fires but the OTE coil never latches in Studio 5000 because the one-shot is only true for one scan. Use OTL/OTU or seal-in logic instead.
Configure Allen-Bradley Kinetix 5500 servo drives on EtherNet/IP. Covers CIP Sync, IEEE 1588 V2 timing, Stratix selection, DLR topology, and HMI.
A moving-average filter is the sliding-window smoother most instrument engineers drop into DCS and PLC analog paths. Here is how the window works, how N and sample time set lag, and when a...
On Frame 5–9 gas turbines, GE Mark VI and Mark VIe run control as function-block application software. This article maps process, protection, and sequencing functions—and what Toolbox ST access...
