Üretici: Honeywell
Ürün No.: TC-FPCXX2
Menşei ülke:Amerika Birleşik Devletleri
Ürün Türü: PLC Power Supply Modules
Ödeme: T/T, Western Union
Ağırlık: 2100g
Boyutlar: 11.2 cm x 14.5 cm x 14.0 cm
Gönderim limanı: Xiamen
Garanti: 12 ay
Providing regulated operating power to local rack configurations, the Honeywell TC-FPCXX2 serves as a high-reliability chassis power supply module engineered for industrial process control environments. This module accepts selectable AC input ranges to deliver a maximum continuous output of 70 W at 60 degC, ensuring stable voltage distribution to adjacent controller and I/O modules. The unit incorporates integrated thermal protection and structural overcurrent safeguarding via an onboard soldered internal fuse to maintain system integrity under transient fault conditions.
| Parameter | Specification Value |
|---|---|
| Manufacturer | Honeywell |
| Model Reference | TC-FPCXX2 |
| Input Voltage Range | 85-132 VAC or 170-265 VAC (User-selectable via slide switch) |
| Line Frequency Range | 47-63 Hz |
| Maximum Output Power | 70 W at 60 degC |
| Overcurrent Protection | Non-replaceable soldered-in input fuse |
| Module Dimensions (W x D x H) | 11.2 cm x 14.5 cm x 14.0 cm (4.41 in x 5.71 in x 5.51 in) |
| Net Module Weight | 1.1 kg (2.43 lbs) |
| Shipping Weight (Calculated) | 2.1 kg (4.63 lbs) |
The TC-FPCXX2 is functionally interchangeable with older Honeywell legacy chassis power options, but caution must be exercised regarding mounting pitch and backplane connector alignment. While standard C200 controllers utilize similar configurations, always verify that the chassis slot keying matches the deep-recessed connector housing on the back of this module before attempting hot insertion.
Because this power supply uses a non-replaceable, soldered-in input fuse, external overcurrent protection (such as an inline terminal block fuse or miniature circuit breaker rated at 5 A or 10 A depending on input configuration) is highly recommended. If an internal component fault triggers the soldered fuse, the entire unit must be serviced or replaced; external fusing mitigates transient line surges from rendering the module permanently inoperable on site.
Before applying power, verify the position of the dual-voltage slide selector switch located on the unit. Energizing a module configured for 115 VAC with a 230 VAC supply line will cause immediate, catastrophic damage to the input varistors and internal circuitry, voiding standard field warranties.
CRITICAL WARNING
Isolate and lock out all incoming AC power lines before mounting or sliding the power module into the chassis. Do not touch terminal screws or the rear connector interface while the main bus is energized. Failure to comply can result in severe electrical shock, equipment destruction, or unexpected process downtime.
Locate the input voltage selector switch on the side or rear of the module. Confirm its setting matches your local utility supply level (115 VAC or 230 VAC nominal).
Align the module with the guide rails of the designated left-most power supply slot in the chassis.
Slide the module firmly backward until the rear interface connector seats fully into the backplane socket. Hand-tighten the integrated retaining screws to secure the unit structurally.
Connect the external, de-energized AC supply wiring to the input terminals, ensuring the protective earth ground wire is established first.
Küresel Ekspres Kargo
İadeler ve Garanti
Siparişler Pazartesi-Cuma günleri işlenir ve teslim edilir (resmi tatiller hariç).
Tam uygunluk, stok yenileme ücretleri ve uluslararası iade detayları için lütfen resmi sayfamızı inceleyin İade ve Geri Ödeme Politikası .
| Country of origin |
Amerika Birleşik Devletleri
|
This article explains how integrated electric actuators, such as SMC’s e-Actuator series, are transforming industrial motion control by replacing traditional pneumatic and hydraulic systems. It...
Bu makale, PLC sistemlerinin endüstriyel otomasyonda toplama, çıkarma, çarpma, bölme, mod alma ve üs alma gibi temel matematiksel işlemleri nasıl gerçekleştirdiğini açıklar. Bu fonksiyon bloklarının,...
Makale, temel AND, OR ve NOT işlemlerinin ötesinde PLC programlamada kullanılan birkaç gelişmiş Boolean mantık fonksiyonunu açıklar. Doğruluk tabloları, çoklayıcılar, darbe üreteçleri ve Schmitt...
Boolean mantığı her PLC programının temelidir. Basit makine kontrollerinden karmaşık endüstriyel otomasyon sistemlerine kadar, mantık kapıları kontrolörlerin değişen girişlere ve çalışma koşullarına...
Endüstriyel güvenlik duvarları, PLC, DCS ve SCADA ağlarını segmentasyon, giriş/çıkış kontrolü ve IEC 62443 prensipleriyle uyumlu IDS/IPS entegrasyonu yoluyla koruyarak OT siber güvenliğinde kritik...
Modern robot tutucular, geleneksel mekanik çenelerin ötesine geçiyor. Geckoya ilham veren yapışkan sistemlerden yumuşak gıda sınıfı tutuculara ve yapay zeka destekli depo araçlarına kadar gelişmiş...
