Produsen: Mitsubishi Electric
Nomor Produk: FR-A840-3.7K
Negara asal:Amerika Serikat
Jenis Produk: Variable Frequency Drives
Pembayaran: T/T, Western Union
Berat: 4400g
Pelabuhan pengiriman: Xiamen
Garansi: 12 bulan
Engineered for high-torque heavy industrial loads, the Mitsubishi Electric FR-A840-3.7K variable frequency drive provides precise vector speed control within the FREQROL-A 800 series portfolio. This high-performance inverter accommodates four distinct duty ratings (SLD, LD, ND, and HD), allowing system integrators to scale motor driving capacity from 2.2 kW up to 5.5 kW based on load profiles. Operating on a three-phase 380 to 500 VAC supply, the FR-A840-3.7K features advanced sensorless vector control, PM sensorless vector control, and built-in RS-485 communications to deliver exceptional speed stability, low-speed torque performance, and seamless automation system integration.
| Parameter | Value / Specification |
|---|---|
| Manufacturer | Mitsubishi Electric |
| Model Number | FR-A840-3.7K |
| Series | FREQROL-A 800 |
| Input Voltage / Frequency | 3-phase 380 to 500 VAC, 50 Hz / 60 Hz |
| Allowable Voltage Fluctuation | 323 to 550 VAC, 50 Hz / 60 Hz |
| Normal Duty (ND) Capacity | 3.7 kW (Rated Current: 9.0 A) |
| Super Light Duty (SLD) Capacity | 5.5 kW (Rated Current: 12.6 A) |
| Heavy Duty (HD) Capacity | 2.2 kW (Rated Current: 6.0 A) |
| Output Voltage Range | 3-phase 380 to 500 VAC |
| Output Frequency Range | 0.2 to 590 Hz (Vector/Sensorless limit: 400 Hz) |
| Overload Current Rating (ND) | 150% for 60 seconds, 200% for 3 seconds (at 50 degC) |
| Cooling Method | Forced Air Cooling |
| Enclosure Protection Rating | IP20 (Closed type) |
| Operating Temperature | -10 to +50 degC (LD/ND/HD without freezing); -10 to +40 degC (SLD) |
| Storage Temperature | -20 to +65 degC |
| Net Mass | 3.3 kg (7.28 lbs) |
| Shipping Weight | 4.4 kg (9.70 lbs) |
| Terminal Designation | Signal Type / Assignment | Electrical Specification |
|---|---|---|
| R/L1, S/L2, T/L3 | AC Power Input | 3-phase 380 to 500 VAC, 50/60 Hz |
| U, V, W | Motor Output Connections | 3-phase modulated variable AC |
| Terminal 2 | Analog Voltage Frequency Command Input | 0 to 5 VDC, 0 to 10 VDC (Selectable) |
| Terminal 4 | Analog Current Frequency Command Input | 4 to 20 mA (or 0 to 20 mA) |
| Terminal 1 | Auxiliary Analog Input (Frequency Offset) | -10 to +10 VDC or -5 to +5 VDC |
| 12 Control Terminals | Configurable Contact Inputs (Multi-speed, Reset, STO) | 24 VDC opto-isolated logic |
The FR-A840-3.7K serves as a direct technical successor to legacy FR-A740-3.7K models. It maintains matching physical mounting patterns, but boasts improved vector algorithm execution. When upgrading a system, parameters from older drives can be extracted and loaded into the newer inverter using Mitsubishi FR Configurator2 software via the integrated USB host port, though phase monitoring characteristics should be verified to prevent minor tuning anomalies on high-inertia loads.
Engineers must exercise caution when operating in the Super Light Duty (SLD) rating class. While SLD elevates continuous output current capacity to 12.6 A for variable torque loads (pumps and fans), the permissible operating ambient temperature drops to 40 degC maximum (compared to 50 degC for standard ND and HD configurations). Placing an SLD-configured unit inside an unventilated outdoor panel can lead to rapid thermal de-rating faults (E.THT or E.TBM) if cabinet ambient temperatures surpass 40 degC.
Ensure that the hardware slide switches located on the control circuit terminal block are configured to match the intended signal type before applying control voltage. If configuring Terminal 4 for 4 to 20 mA current input, check that Parameter 267 is set to '0' (initial value) and the input selection switch is in the 'I' position. Leaving the switch in 'V' (voltage) while applying a current loop input can damage the analog input circuitry.
CRITICAL WARNING: HIGH VOLTAGE RISK
Before executing any wiring or maintenance operations on this variable frequency drive, isolate the AC primary supply and wait a minimum of 10 minutes. Use a calibrated DC voltmeter to confirm that the DC bus charge LED has extinguished and that voltage across terminal P/+ and N/- has dropped below 30 VDC. Failure to observe discharge times can result in lethal shock or device destruction.
Pengiriman Ekspres Global
Pengembalian & Garansi
Pesanan diproses dan dikirimkan Senin-Jumat (tidak termasuk hari libur nasional).
Untuk kelayakan penuh, biaya pengisian ulang, dan detail pengembalian internasional, silakan lihat resmi kami Kebijakan Pengembalian & Pengembalian Dana .
| Country of origin |
Amerika Serikat
|
Artikel ini menjelaskan bagaimana aktuator listrik terintegrasi, seperti seri e-Actuator dari SMC, mengubah kontrol gerak industri dengan menggantikan sistem pneumatik dan hidrolik tradisional....
Artikel ini menjelaskan bagaimana sistem PLC melakukan operasi matematika inti seperti penjumlahan, pengurangan, perkalian, pembagian, modulo, dan perpangkatan dalam otomasi industri. Artikel ini...
Artikel ini menjelaskan beberapa fungsi logika Boolean lanjutan yang digunakan dalam pemrograman PLC selain operasi dasar AND, OR, dan NOT. Artikel ini membahas bagaimana alat seperti tabel...
Logika Boolean adalah dasar dari setiap program PLC. Dari kontrol mesin sederhana hingga sistem otomasi industri yang kompleks, gerbang logika menentukan bagaimana pengendali merespons perubahan...
Firewall industri memainkan peran penting dalam keamanan siber OT, melindungi jaringan PLC, DCS, dan SCADA melalui segmentasi, kontrol masuk/keluar, dan integrasi IDS/IPS yang sesuai dengan prinsip...
Gripper robot modern berkembang melampaui rahang mekanis tradisional. Mulai dari sistem adhesif yang terinspirasi oleh cicak dan gripper lembut yang aman untuk makanan hingga alat gudang bertenaga...
