Optimized for high-precision motion control, the Lenze EVS9325-EKV004 servo drive delivers reliable dynamic performance within the legacy 9300 Series architecture. This industrial servo controller features integrated cam profiling capabilities, making it highly suitable for complex synchronized motion sequences. Engineered with a 5.5 kW rated power capacity and housed in an IP20 rated enclosure, the unit is designed for space-efficient control cabinet installation. Although this model is currently in its phase-out lifecycle stage, it remains a critical component for maintaining and servicing existing high-performance automation systems.
| Parameter | Specification |
|---|---|
| Manufacturer | Lenze |
| Model Number | EVS9325-EKV004 |
| Product Series | 9300 Series (Servo Cam Profiler) |
| Rated Power | 5.5 kW |
| Enclosure Rating | IP20 |
| Product Lifecycle Status | Phase-Out (Active until 2017) |
| Physical Dimensions | 35.00 x 25.00 x 13.50 cm |
| Net Weight | 7.50 kg |
| Commodity Code | 85044095 |
| Export Control Classification (ECCN) | N |
As a legacy component of the Lenze 9300 series, direct physical drop-in replacements are limited. For modern system retrofits, migration to the Lenze i950 cabinet servo inverter series is recommended. Note that migrating to newer platforms requires updated control configurations, mechanical mounting adjustments, and fieldbus communication mapping.
Because the unit is rated IP20, it must be installed in a clean, dust-free control cabinet with adequate ventilation. At a 5.5 kW power rating, thermal dissipation must be carefully calculated. Ensure that the cabinet cooling system can handle the continuous heat output of the drive under peak operating cycles to prevent thermal tripping.
When replacing an existing EVS9325-EKV004, always back up the parameter set from the old drive using Lenze Global Drive Control (GDC) software before decommissioning. Ensure that the parameter chip is compatible with the firmware revision of the replacement unit to avoid initialization errors during startup.
CRITICAL WARNING
Isolate all electrical power sources before handling or wiring the drive. After disconnecting the main AC power supply, wait at least 5 minutes to allow the internal DC-bus capacitors to discharge fully to safe voltage levels before touching terminals.
Mount the servo drive vertically on a flat, vibration-resistant backplate inside a protected control enclosure.
Connect the protective earth (PE) conductor to the designated grounding terminal prior to making any other electrical connections.
Route motor power and resolver/encoder cables separately from control signaling lines to minimize electromagnetic interference (EMI).
Verify all terminal connection torques and ensure correct polarity of the DC bus and AC input lines before energizing the system.
Global Express Shipping
Returns & Warranty
Manufacturer: Lenze
Product No.: EVS9325-EKV004
Country of origin:Germany
Product Type: Servo Drives
Barcode: 85044095
Payment: T/T, Western Union
Weight: 7500g
Dimensions: 35.00 x 25.00 x 13.50 cm
Shipping port: Xiamen
Warranty: 12 months
Optimized for high-precision motion control, the Lenze EVS9325-EKV004 servo drive delivers reliable dynamic performance within the legacy 9300 Series architecture. This industrial servo controller features integrated cam profiling capabilities, making it highly suitable for complex synchronized motion sequences. Engineered with a 5.5 kW rated power capacity and housed in an IP20 rated enclosure, the unit is designed for space-efficient control cabinet installation. Although this model is currently in its phase-out lifecycle stage, it remains a critical component for maintaining and servicing existing high-performance automation systems.
| Parameter | Specification |
|---|---|
| Manufacturer | Lenze |
| Model Number | EVS9325-EKV004 |
| Product Series | 9300 Series (Servo Cam Profiler) |
| Rated Power | 5.5 kW |
| Enclosure Rating | IP20 |
| Product Lifecycle Status | Phase-Out (Active until 2017) |
| Physical Dimensions | 35.00 x 25.00 x 13.50 cm |
| Net Weight | 7.50 kg |
| Commodity Code | 85044095 |
| Export Control Classification (ECCN) | N |
As a legacy component of the Lenze 9300 series, direct physical drop-in replacements are limited. For modern system retrofits, migration to the Lenze i950 cabinet servo inverter series is recommended. Note that migrating to newer platforms requires updated control configurations, mechanical mounting adjustments, and fieldbus communication mapping.
Because the unit is rated IP20, it must be installed in a clean, dust-free control cabinet with adequate ventilation. At a 5.5 kW power rating, thermal dissipation must be carefully calculated. Ensure that the cabinet cooling system can handle the continuous heat output of the drive under peak operating cycles to prevent thermal tripping.
When replacing an existing EVS9325-EKV004, always back up the parameter set from the old drive using Lenze Global Drive Control (GDC) software before decommissioning. Ensure that the parameter chip is compatible with the firmware revision of the replacement unit to avoid initialization errors during startup.
CRITICAL WARNING
Isolate all electrical power sources before handling or wiring the drive. After disconnecting the main AC power supply, wait at least 5 minutes to allow the internal DC-bus capacitors to discharge fully to safe voltage levels before touching terminals.
Mount the servo drive vertically on a flat, vibration-resistant backplate inside a protected control enclosure.
Connect the protective earth (PE) conductor to the designated grounding terminal prior to making any other electrical connections.
Route motor power and resolver/encoder cables separately from control signaling lines to minimize electromagnetic interference (EMI).
Verify all terminal connection torques and ensure correct polarity of the DC bus and AC input lines before energizing the system.
Global Express Shipping
Returns & Warranty
Orders are processed and delivered Monday-Friday (excluding public holidays).
For full eligibility, restocking fees, and international return details, please view our official Refund & Return Policy .
| Country of origin |
Germany
|
A practical engineering guide to PLC CPU operation, from deterministic scan cycles and I/O image tables to memory, communications, diagnostics, redundancy, processor sizing, and reliable system...
Sostituire un 1756-L73 non significa automaticamente aggiornare il firmware. Questa guida confronta le versioni 19.013, 21.011 e 31.011, concentrandosi sulla compatibilità dei progetti, sulle...
Implementa un circuito luminoso XOR con 3 interruttori SPST in LogixPro o RSLogix 500 utilizzando un bit di relè interno. Include tabelle della verità, equazioni booleane e verifica.
Integra Allen-Bradley CompactLogix, Caterpillar ATS e generatori nel DCS DeltaV tramite Modbus RTU. Include i gateway ProSoft MVI69-MCM e Miille DIN266.
L’istruzione ONS si attiva, ma la bobina OTE non rimane mai eccitata in Studio 5000 perché il one-shot è vero solo per una scansione. Usa OTL/OTU oppure una logica di autoritenuta.
Configura i servoazionamenti Allen-Bradley Kinetix 5500 su EtherNet/IP. Include CIP Sync, la temporizzazione IEEE 1588 V2, la selezione degli switch Stratix, la topologia DLR e l’HMI.
