330901-00-90-10-02-05 specifies a 3300 NSv proximity probe with a 1/4-28 UNF thread and no armor. This specific configuration features 0.0 inches of unthreaded length, a 9.0-inch overall case length, a 1.0-meter (39 in) total cable length, a miniature coaxial ClickLoc connector with a standard cable, and multiple agency approvals.
The 3300 NSv system is used for non-contact shaft vibration and position measurements on machines with limited clearance or reduced target geometries, such as centrifugal air compressors, refrigeration compressors, and small-bore rotating machinery. The unarmored cable design provides clean routing in tight enclosures, and the gold-plated ClickLoc connector prevents connection loosening during operation. It is electrically and mechanically interchangeable with older 3300 RAM systems, offering superior side-view characteristics and enhanced chemical resistance.
| Option Segment | Code Value | Configuration Meaning |
|---|---|---|
| Orderable Part Number | 330901-00-90-10-02-05 | 3300 NSv Proximity Probe, 1/4-28 UNF thread, without armor |
| A: Unthreaded Length Option | 00 | 0.0 in unthreaded length |
| B: Overall Case Length Option | 90 | 9.0 in overall case length |
| C: Total Length Option | 10 | 1.0 meter (39 in) total probe length |
| D: Connector and Cable-Type Option | 02 | Miniature coaxial ClickLoc connector, standard cable |
| E: Agency Approval Option | 05 | Multiple Approvals (including CSA, ATEX, IECEx) |
| Manufacturer | Bently Nevada (Baker Hughes) |
| Model Number | 330901-00-90-10-02-05 |
| System Type | 3300 XL NSv Proximity Transducer System |
| Thread Size | 1/4-28 UNF-2A |
| Armor Option | Without armor |
| Linear Range | 1.5 mm (60 mils), from approximately 0.25 to 1.75 mm (10 to 70 mils) |
| Recommended Gap | 1.0 mm (40 mils) |
| Incremental Scale Factor (ISF) | 7.87 V/mm (200 mV/mil) +12.5% / -20% over ambient range (0 to 45 degC) |
| Deviation from Best Fit Straight Line (DSL) | Less than +/-0.06 mm (+/-2.3 mils) over linear range |
| Frequency Response | 0 to 10 kHz: +0, -3 dB typical with up to 305 meters of field wiring |
| Probe Tip Material | Polyphenylene sulfide (PPS) |
| Probe Case Material | AISI 304 stainless steel (SST) |
| Cable Type | 75 ohm coaxial, fluoroethylene propylene (FEP) insulated standard probe cable |
| Connector Type | Gold-plated brass ClickLoc miniature male coaxial connector |
| Operating and Storage Temperature | -52 to +177 degC (-62 to +351 degF) |
| Probe dc Resistance (R_PROBE) | 4.2 +/- 0.5 ohms (for 1.0 m total probe length) |
| Probe Pressure Rating | Differential pressure seal with Viton O-ring between probe tip and case |
| Minimum Bend Radius | 25.4 mm (1.0 in) |
Global Express Shipping
Returns & Warranty
Manufacturer: Bently Nevada
Product No.: 330901-00-90-10-02-05
Country of origin:United States
Product Type: 3300 NSv Proximity Probes
Barcode: 8537101190
Payment: T/T, Western Union
Weight: 120g
Dimensions: 45 mm x 90 mm x 90 mm (H x W x D)
Shipping port: Xiamen
Warranty: 12 months
330901-00-90-10-02-05 specifies a 3300 NSv proximity probe with a 1/4-28 UNF thread and no armor. This specific configuration features 0.0 inches of unthreaded length, a 9.0-inch overall case length, a 1.0-meter (39 in) total cable length, a miniature coaxial ClickLoc connector with a standard cable, and multiple agency approvals.
The 3300 NSv system is used for non-contact shaft vibration and position measurements on machines with limited clearance or reduced target geometries, such as centrifugal air compressors, refrigeration compressors, and small-bore rotating machinery. The unarmored cable design provides clean routing in tight enclosures, and the gold-plated ClickLoc connector prevents connection loosening during operation. It is electrically and mechanically interchangeable with older 3300 RAM systems, offering superior side-view characteristics and enhanced chemical resistance.
| Option Segment | Code Value | Configuration Meaning |
|---|---|---|
| Orderable Part Number | 330901-00-90-10-02-05 | 3300 NSv Proximity Probe, 1/4-28 UNF thread, without armor |
| A: Unthreaded Length Option | 00 | 0.0 in unthreaded length |
| B: Overall Case Length Option | 90 | 9.0 in overall case length |
| C: Total Length Option | 10 | 1.0 meter (39 in) total probe length |
| D: Connector and Cable-Type Option | 02 | Miniature coaxial ClickLoc connector, standard cable |
| E: Agency Approval Option | 05 | Multiple Approvals (including CSA, ATEX, IECEx) |
| Manufacturer | Bently Nevada (Baker Hughes) |
| Model Number | 330901-00-90-10-02-05 |
| System Type | 3300 XL NSv Proximity Transducer System |
| Thread Size | 1/4-28 UNF-2A |
| Armor Option | Without armor |
| Linear Range | 1.5 mm (60 mils), from approximately 0.25 to 1.75 mm (10 to 70 mils) |
| Recommended Gap | 1.0 mm (40 mils) |
| Incremental Scale Factor (ISF) | 7.87 V/mm (200 mV/mil) +12.5% / -20% over ambient range (0 to 45 degC) |
| Deviation from Best Fit Straight Line (DSL) | Less than +/-0.06 mm (+/-2.3 mils) over linear range |
| Frequency Response | 0 to 10 kHz: +0, -3 dB typical with up to 305 meters of field wiring |
| Probe Tip Material | Polyphenylene sulfide (PPS) |
| Probe Case Material | AISI 304 stainless steel (SST) |
| Cable Type | 75 ohm coaxial, fluoroethylene propylene (FEP) insulated standard probe cable |
| Connector Type | Gold-plated brass ClickLoc miniature male coaxial connector |
| Operating and Storage Temperature | -52 to +177 degC (-62 to +351 degF) |
| Probe dc Resistance (R_PROBE) | 4.2 +/- 0.5 ohms (for 1.0 m total probe length) |
| Probe Pressure Rating | Differential pressure seal with Viton O-ring between probe tip and case |
| Minimum Bend Radius | 25.4 mm (1.0 in) |
Global Express Shipping
Returns & Warranty
Orders are processed and delivered Monday-Friday (excluding public holidays).
For full eligibility, restocking fees, and international return details, please view our official Refund & Return Policy .
| Country of origin |
United States
|
Replacing a 1756-L73 does not automatically mean upgrading its firmware. This guide compares v19.013, v21.011 and v31.011, focusing on project compatibility, HMI communications, legacy networks and...
Implement a 3-SPST switch XOR light circuit in LogixPro or RSLogix 500 using an internal relay bit. Includes truth tables, boolean equations, and verified.
Integrate Allen-Bradley CompactLogix, Caterpillar ATS, and generators into DeltaV DCS over Modbus RTU. Covers ProSoft MVI69-MCM, Miille DIN266 gateways.
ONS instruction fires but the OTE coil never latches in Studio 5000 because the one-shot is only true for one scan. Use OTL/OTU or seal-in logic instead.
Configure Allen-Bradley Kinetix 5500 servo drives on EtherNet/IP. Covers CIP Sync, IEEE 1588 V2 timing, Stratix selection, DLR topology, and HMI.
A moving-average filter is the sliding-window smoother most instrument engineers drop into DCS and PLC analog paths. Here is how the window works, how N and sample time set lag, and when a...
