Manufacturer: Bently Nevada
Product No.: AM3100T2-Z2
Country of origin:United States
Product Type: Accelerometer Sensor
Barcode: 8537101190
Payment: T/T, Western Union
Weight: 62g
Dimensions: 1.8cm x 1.6cm x 123cm
Shipping port: Xiamen
Warranty: 12 months
The AM3100T2-Z2 is an Integrated Electronics Piezo-Electric (IEPE) accelerometer optimized for obtaining high quality vibration signals in harsh industrial environments. Its piezo sensing element provides exceptional dynamic range, frequency range, and linearity, while the integrated amplifier boosts the signal and improves immunity to electrical noise.
The sensor requires an industry standard constant-current power supply and provides an output voltage proportional to the acceleration signal, allowing interface with a wide variety of condition monitoring systems.
The AM3100T2-Z2 features a top-exit connector configuration, 100 mV/g sensitivity, and Zone 2 hazardous-area certification.
| ParameterValue | |
| Sensitivity, ±5% @25°C | 100 mV/g |
| Acceleration range | 80 g peak |
| Amplitude nonlinearity | 1% |
| Frequency response ±10% | 0.7-9,000 Hz |
| Frequency response ±3 dB | 0.4-14,000 Hz |
| Resonant frequency | 30 kHz |
| Transverse sensitivity, max | ±5% of axial |
| Temperature response | -55°C : -20% / +120°C : +10% |
| ParameterValue | |
| Voltage source | 18-30 Vdc |
| Current regulating diode | 2-10 mA |
| Broadband electrical noise @ 2.5 Hz to 25 kHz | 500 μg |
| Spectral electrical noise @ 10 Hz | 7 μg/√Hz |
| Spectral electrical noise @ 100 Hz | 4 μg/√Hz |
| Spectral electrical noise @ 1000 Hz | 2 μg/√Hz |
| Output Impedance, max | 100 Ω |
| Bias output voltage | 12 Vdc |
| Grounding | Case isolated, internally shielded |
| ParameterValue | |
| Temperature range | -55°C to 120°C |
| Vibration limit | 500 g peak |
| Shock limit | 5,000 g peak |
| Electromagnetic sensitivity, equiv g, max | 70 μg/gauss |
| Sealing | Hermetic |
| Base strain sensitivity, max | 0.0002 g/μstrain |
| ParameterValue | |
| Sensing element design | PZT ceramic / shear |
| Weight | 62 grams |
| Case material | 316L Stainless Steel |
| Mounting | ¼-28 UNF tapped hole |
| Connector | Top exit, 2-pin, MIL-C-5015 style |
| Recommended cabling | Shielded, twisted pair, no longer than 100 feet |
| Connector PinFunction | |
| Shell | Ground |
| A | Power / Signal |
| B | Common |
Frequency response and spectral noise values are typical.
Install the sensor on a clean, flat, and rigid mounting surface. Remove paint, rust, grease, and debris before installation to ensure proper mechanical coupling and accurate vibration transmission.
Poor mounting surfaces may reduce high-frequency response and introduce measurement errors.
Use the supplied ¼-28 mounting stud for installation.
Installation recommendations:
Use shielded twisted-pair cable as recommended by the manufacturer.
For best signal quality:
Recommended cable length should not exceed 100 feet.
The sensor uses a top-exit 2-pin MIL-C-5015 style connector.
In wet or outdoor environments:
The hermetic sensor body helps protect against moisture ingress when properly installed.
The AM3100T2-Z2 requires an IEPE constant-current power source.
Required electrical supply:
Verify compatibility with the monitoring system before commissioning.
The sensor is case isolated and internally shielded to help reduce ground loop problems.
Recommended practices:
The AM3100T2-Z2 is approved for Zone 2 hazardous locations.
Installation must comply with:
Ensure all associated wiring, barriers, and cable glands meet hazardous-area installation requirements.
The AM3100T2-Z2 is an IEPE accelerometer designed for industrial vibration monitoring applications.
The sensor sensitivity is 100 mV/g (±5% at 25°C).
The sensor supports an acceleration range of 80 g peak.
Frequency response specifications are:
The sensor requires:
Yes. The AM3100T2-Z2 is certified for Zone 2 hazardous-area applications.
The device uses a top-exit 2-pin MIL-C-5015 style connector.
No. The sensor is case isolated and internally shielded.
The operating temperature range is -55°C to 120°C.
Yes. The sensor has a hermetic seal and can operate in wet environments when proper sealed connectors and cables are used.
The mounting interface is a ¼-28 UNF tapped hole.
Shielded twisted-pair cable is recommended, with a maximum length of 100 feet.
Yes. The device includes reverse wiring protection to help prevent damage caused by incorrect wiring.
Global Express Shipping
Returns & Warranty
Global Express Shipping
Returns & Warranty
Orders are processed and delivered Monday-Friday (excluding public holidays).
For full eligibility, restocking fees, and international return details, please view our official Refund & Return Policy .
| Color pattern |
Gold
Silver
|
| Country of origin |
United States
|
Learn what derivative action contributes to a PID loop, why it can amplify measurement noise and setpoint changes, and how filtering, sampling, and staged tests make D tuning safer.
A practical guide to segmenting, documenting, and testing industrial Ethernet networks so plant teams can isolate faults quickly, control change, and expand without creating fragile dependencies.
Commission IO-Link systematically from master addressing and port modes through IODD selection, PLC byte mapping, parameter backups, device validation, and failure-injection tests.
A practical PowerFlex braking guide covering regenerative energy, resistor resistance and duty cycle, thermal protection, model-specific parameters, and measured commissioning tests.
An industrial joystick is only the first element in a safe motion command chain. This guide covers sensing choices, wiring, signal validation, PLC logic, restart behavior, and commissioning for...
PID tuning becomes safer when engineers can see how proportional, integral, and derivative actions reshape error, output, and response over time. This guide turns live trends into a disciplined...
