Système de mesure à courant de Foucault 16 mm Emerson Epro PR6424/104-141 CON041

Product Overview

The PR6424/104-141 CON041 (PR6424/104-141 CON041) is an integrated high-precision eddy current measurement set designed for the most demanding turbomachinery protection environments. This system combines a 16 mm diameter sensor with a dedicated CON041 signal converter to monitor shaft vibration, axial position, and eccentricity in heavy-duty rotating assets such as steam turbines, high-pressure compressors, and large hydro-generators. By utilizing a larger sensor head, the system achieves a significant measurement range and enhanced stability compared to standard probes. This assembly is a critical component of Turbine Supervisory Instrumentation (TSI), providing the real-time data necessary for the Emerson AMS 6500 to prevent catastrophic mechanical failure and ensure maximum plant availability in industries like power generation and oil refining.

Technical Configuration (Deep Dive)

This system operates on the inductive eddy current principle, where the CON041 driver provides high-frequency excitation to the 16 mm sensor head.

• 16 mm Sensor Architecture (PR6424): The "104-141" configuration specifies a ruggedized sensor with a 16 mm tip, optimized for large shaft diameters (greater than or equal to 80 mm). The larger coil diameter provides a deeper magnetic field penetration, which is essential for measuring high-amplitude vibrations or large axial displacements.

• Signal Converter Logic (CON041): The converter acts as a high-speed processor that demodulates the impedance changes in the sensor into a standardized analog voltage. It features a fast rise time of less than 15 microseconds, ensuring even high-frequency transients are captured accurately.

• Environmental Resilience: The sensor head is hermetically sealed and pressure-resistant up to 10,000 hPa (145 psi), allowing for installation in pressurized oil-lubricated bearing housings.

• Armored Integration: The "1" in the configuration typically denotes a reinforced armored cable, providing mechanical protection against sharp edges and physical stress in industrial conduit systems.

Technical Specifications

Technical FAQs

Q1: Why use a 16 mm sensor like the PR6424 instead of a standard 8 mm sensor?

A1: The 16 mm tip provides a much larger linear measuring range (up to 8.0 mm). This is vital for large machines where thermal expansion or axial "float" exceeds the 2.0 mm limit of smaller sensors.

Q2: What is the significance of the target material for this system?

A2: Eddy current sensors are sensitive to the conductivity and permeability of the target. This system is factory-calibrated for Ferromagnetic Steel (42 Cr Mo4). Using other materials will require a sensitivity adjustment in the monitoring system.

Q3: Can the CON041 be mounted directly on the machine?

A3: No, the CON041 is an IP20 rated device and must be installed in a protected junction box or control cabinet using standard DIN rail mounting to prevent damage from moisture and dust.

Engineering & Installation Guide

• Gap Voltage Calibration: For the 8.0 mm measuring range, the nominal air gap center is approximately 2.7 mm. During installation, adjust the sensor position until the CON041 output voltage reaches the midpoint of the linear curve (typically -10 VDC).

• Target Surface Finish: To prevent "electrical runout," the shaft surface must be free of scratches, tool marks, and magnetic spots. A surface finish of 1.0 micrometer Ra or better is recommended for vibration measurements.

• Cable Protection: Ensure the armored cable is securely clamped but not crushed. Maintain a minimum bend radius to prevent internal damage to the coaxial core, which is critical for maintaining the tuned resonance frequency of the system.

Engineering Advantages

The PR6424/104-141 CON041 set offers an industry-leading long-term drift of less than 0.3%, ensuring that the safety protection system remains accurate between major plant turnarounds. The 16 mm head design provides a superior signal-to-noise ratio, allowing for the detection of subtle changes in machine health even in electrically noisy environments near high-power generators. Furthermore, its downward compatibility with older Philips epro systems simplifies the modernization of legacy TSI hardware without requiring structural modifications to the machine casing.