Bently Nevada 330902-00-30-05-02-05 3300 NSv Proximity Probe

Description

330902-00-30-05-02-05 specifies this standard-mount 3300 NSv Proximity Probe configuration, featuring a 1/4-28 UNF thread with integrated stainless steel armor, 0.0 in of unthreaded length, a 3.0 in overall case length, a 0.5 m (20 in) total probe length, a miniature ClickLoc coaxial connector on a standard cable, and multiple agency approvals.

This armored probe configuration protects the 75 ohm FEP-insulated coaxial cable from physical wear and environmental damage within tight machinery enclosures. It operates within the 3300 XL NSv transducer system, interfacing with a 330930 extension cable and a 330980 Proximitor Sensor to measure non-contact static and dynamic displacement on machines with reduced target areas or tight clearance restrictions.

Features

• Standard-mount threaded probe with 1/4-28 UNF-2A thread configuration and integrated stainless steel armor.
• Option 00 unthreaded length providing a fully threaded 3.0 in case (Option 30) for flexible depth adjustment.
• 0.5 m (20 in) total probe length (Option 05) utilizing standard 75 ohm FEP-insulated coaxial cable.
• Miniature male ClickLoc coaxial connector (Option 02) for secure locking without tools.
• Option 05 multiple approvals package covering hazardous area certifications (CSA, ATEX, IECEx).
• Polyphenylene sulfide (PPS) probe tip material molded with patented TipLoc technology for a robust mechanical bond.
• Patented CableLoc design providing up to 220 N (50 lb) of pull strength between the probe case and the cable.

Applications

• Radial vibration and position monitoring on fluid-film bearing shafts smaller than 51 mm (2.0 in).
• Axial (thrust) position measurements on flat targets smaller than 15 mm (0.6 in).
• Centrifugal air compressors, refrigeration compressors, and high-speed process gas compressors.
• Aeroderivative gas turbines and machinery with highly restricted counterbore, sideview, or rearview clearances.
• Tachometer, zero-speed, and phase reference (Keyphasor) signal generation.

Ordering Information

Technical Specifications

Installation Guidelines

• Ensure the probe cable and armor respect the minimum bend radius of 25.4 mm (1.0 in) during installation and routing.
• Tighten the 1/4-28 UNF probe case to the recommended installation torque of 5.1 N m (45 in lb); do not exceed the maximum rated limit of 7.3 N m (65 in lb) to avoid case damage.
• Ensure the unthreaded probe length is at least 0.7 inches less than the case length to maintain structural support.
• Use a mechanical gap setting of 1.0 mm (40 mils) to position the system in the center of its 1.5 mm linear range.
• Protect standard probe-to-extension cable connections using connector protectors or silicone tape to prevent oil and moisture ingress. Do not apply silicone tape if exposed to turbine oil.

Compliance and Certifications

• CSA/NRTL/C: Class I, Zone 0: AEx/Ex ia IIC T4/T5 Ga; Class I, Groups A, B, C, D; Class II, Groups E, F, G; Class III (intrinsically safe)
• ATEX/IECEx: Ex ia IIC T5...T1 Ga (EPL Ga), Ex ia IIIC T90 degC...T280 degC Dc (EPL Dc), Ex nA/ec IIC T5...T1 Gc (EPL Gc)
• EMC Directive: 2014/30/EU (EN 61000-6-2, EN 61000-6-4)
• RoHS Directive: 2011/65/EU