330906-02-12-05-02-00 specifies a Bently Nevada 3300 NSv reverse mount proximity probe configured with an unthreaded case length of 0.2 inches, an overall case length of 1.2 inches, and a 3/8-24 UNF-2A thread profile. This probe option features a 0.5-meter (20-inch) standard FEP cable with a miniature coaxial ClickLoc connector and is supplied without hazardous area agency approvals. Unlike standard-mount models that are screwed into place from outside the machine housing, reverse-mount probes are installed from the inside or rear, protecting the sensor body and maintaining position settings in tight spaces.
This probe operates with a 3300 XL NSv proximity transducer system and is interchangeable with legacy 3300 RAM proximity probe installations. The transducer system provides non-contact shaft vibration and axial position measurements on small-bore machinery or high-speed machinery where clearance constraints limit probe tip diameter.
The 3300 NSv reverse mount probe is used for non-contact displacement, radial vibration, and axial position measurements in rotating machinery. It is suited for high-speed machinery with limited target geometry, such as aeroderivative gas turbines, centrifugal compressors, small pumps, and auxiliary equipment where standard probe casing clearances are insufficient.
| Option / Segment | Code on This SKU | Description / Meaning |
|---|---|---|
| Base Model Number | 330906 | 3300 NSv Reverse Mount Probe, 3/8-24 UNF threads |
| A - Unthreaded Length Option | 02 | 0.2 in (5.1 mm) unthreaded length |
| B - Overall Case Length Option | 12 | 1.2 in (30.5 mm) overall case length |
| C - Total Length Option | 05 | 0.5 meters (20 inches) total length |
| D - Connector Option | 02 | Miniature coaxial ClickLoc connector, standard cable |
| E - Agency Approval Option | 00 | Not required (Standard / Safe Area) |
| Manufacturer | Bently Nevada (Baker Hughes) |
| Part Number | 330906-02-12-05-02-00 |
| System Compatibility | 3300 XL NSv Proximity Transducer System |
| Measurement Type | Non-contact eddy current displacement / position |
| Thread Type | 3/8-24 UNF-2A reverse mount threads |
| Unthreaded Length | 0.2 inches (5.1 mm) |
| Case Length | 1.2 inches (30.5 mm) |
| Probe Cable Length | 0.5 meters (20 inches) |
| Connector Type | Miniature coaxial ClickLoc connector |
| Cable Type | Standard 75-ohm coaxial (FEP insulated) |
| Linear Range | 1.5 mm (60 mils) from 0.25 to 1.75 mm (10 to 70 mils) |
| Recommended Gap Setting | 1.0 mm (40 mils) |
| Incremental Scale Factor | 7.87 V/mm (200 mV/mil) +12.5% / -20% |
| Deviation from Straight Line (DSL) | Less than +/-0.06 mm (+/-2.3 mils) |
| Frequency Response | 0 to 10 kHz (+0, -3 dB typical) |
| Operating and Storage Temperature | -52 degC to +177 degC (-62 degF to +351 degF) |
| Pressure Sealing Material | Viton O-ring |
| Probe Tip Material | Polyphenylene sulfide (PPS) |
| Probe Case Material | AISI 304 stainless steel (SST) |
| Connector Material | Gold-plated brass |
| Maximum Tensile Strength | 220 N (50 lb) case-to-lead and connector-to-connector |
| Agency Approvals | Not required (Safe Area / standard environments) |
Proper installation of the 3300 NSv reverse mount probe provides accurate vibration and axial measurements:
The 3300 XL NSv Proximity Transducer System components conform to the following standards when used as a system:
Global Express Shipping
Returns & Warranty
Manufacturer: Bently Nevada
Product No.: 330906-02-12-05-02-00
Country of origin:United States
Product Type: 3300 NSv Reverse Mount Probe
Barcode: 8537101190
Payment: T/T, Western Union
Weight: 120g
Dimensions: 45 mm x 90 mm x 90 mm (H x W x D)
Shipping port: Xiamen
Warranty: 12 months
330906-02-12-05-02-00 specifies a Bently Nevada 3300 NSv reverse mount proximity probe configured with an unthreaded case length of 0.2 inches, an overall case length of 1.2 inches, and a 3/8-24 UNF-2A thread profile. This probe option features a 0.5-meter (20-inch) standard FEP cable with a miniature coaxial ClickLoc connector and is supplied without hazardous area agency approvals. Unlike standard-mount models that are screwed into place from outside the machine housing, reverse-mount probes are installed from the inside or rear, protecting the sensor body and maintaining position settings in tight spaces.
This probe operates with a 3300 XL NSv proximity transducer system and is interchangeable with legacy 3300 RAM proximity probe installations. The transducer system provides non-contact shaft vibration and axial position measurements on small-bore machinery or high-speed machinery where clearance constraints limit probe tip diameter.
The 3300 NSv reverse mount probe is used for non-contact displacement, radial vibration, and axial position measurements in rotating machinery. It is suited for high-speed machinery with limited target geometry, such as aeroderivative gas turbines, centrifugal compressors, small pumps, and auxiliary equipment where standard probe casing clearances are insufficient.
| Option / Segment | Code on This SKU | Description / Meaning |
|---|---|---|
| Base Model Number | 330906 | 3300 NSv Reverse Mount Probe, 3/8-24 UNF threads |
| A - Unthreaded Length Option | 02 | 0.2 in (5.1 mm) unthreaded length |
| B - Overall Case Length Option | 12 | 1.2 in (30.5 mm) overall case length |
| C - Total Length Option | 05 | 0.5 meters (20 inches) total length |
| D - Connector Option | 02 | Miniature coaxial ClickLoc connector, standard cable |
| E - Agency Approval Option | 00 | Not required (Standard / Safe Area) |
| Manufacturer | Bently Nevada (Baker Hughes) |
| Part Number | 330906-02-12-05-02-00 |
| System Compatibility | 3300 XL NSv Proximity Transducer System |
| Measurement Type | Non-contact eddy current displacement / position |
| Thread Type | 3/8-24 UNF-2A reverse mount threads |
| Unthreaded Length | 0.2 inches (5.1 mm) |
| Case Length | 1.2 inches (30.5 mm) |
| Probe Cable Length | 0.5 meters (20 inches) |
| Connector Type | Miniature coaxial ClickLoc connector |
| Cable Type | Standard 75-ohm coaxial (FEP insulated) |
| Linear Range | 1.5 mm (60 mils) from 0.25 to 1.75 mm (10 to 70 mils) |
| Recommended Gap Setting | 1.0 mm (40 mils) |
| Incremental Scale Factor | 7.87 V/mm (200 mV/mil) +12.5% / -20% |
| Deviation from Straight Line (DSL) | Less than +/-0.06 mm (+/-2.3 mils) |
| Frequency Response | 0 to 10 kHz (+0, -3 dB typical) |
| Operating and Storage Temperature | -52 degC to +177 degC (-62 degF to +351 degF) |
| Pressure Sealing Material | Viton O-ring |
| Probe Tip Material | Polyphenylene sulfide (PPS) |
| Probe Case Material | AISI 304 stainless steel (SST) |
| Connector Material | Gold-plated brass |
| Maximum Tensile Strength | 220 N (50 lb) case-to-lead and connector-to-connector |
| Agency Approvals | Not required (Safe Area / standard environments) |
Proper installation of the 3300 NSv reverse mount probe provides accurate vibration and axial measurements:
The 3300 XL NSv Proximity Transducer System components conform to the following standards when used as a system:
Global Express Shipping
Returns & Warranty
Orders are processed and delivered Monday-Friday (excluding public holidays).
For full eligibility, restocking fees, and international return details, please view our official Refund & Return Policy .
| Country of origin |
United States
|
A practical engineering guide to PLC CPU operation, from deterministic scan cycles and I/O image tables to memory, communications, diagnostics, redundancy, processor sizing, and reliable system...
Replacing a 1756-L73 does not automatically mean upgrading its firmware. This guide compares v19.013, v21.011 and v31.011, focusing on project compatibility, HMI communications, legacy networks and...
Implement a 3-SPST switch XOR light circuit in LogixPro or RSLogix 500 using an internal relay bit. Includes truth tables, boolean equations, and verified.
Integrate Allen-Bradley CompactLogix, Caterpillar ATS, and generators into DeltaV DCS over Modbus RTU. Covers ProSoft MVI69-MCM, Miille DIN266 gateways.
ONS instruction fires but the OTE coil never latches in Studio 5000 because the one-shot is only true for one scan. Use OTL/OTU or seal-in logic instead.
Configure Allen-Bradley Kinetix 5500 servo drives on EtherNet/IP. Covers CIP Sync, IEEE 1588 V2 timing, Stratix selection, DLR topology, and HMI.
