Manufacturer: Bently Nevada
Product No.: 9200-03-05-10-00
Country of origin:United States
Product Type: Velocity Transducers
Payment: T/T, Western Union
Weight: 320g
Shipping port: Xiamen
Warranty: 12 months
Designed for continuous machinery vibration monitoring, the Bently Nevada 9200-03-05-10-00 functions as a self-generating, two-wire velocity sensor that translates casing vibration into an electrical signal. This moving-coil transducer is engineered specifically for vertical installation configurations, operating at a 90-degree angle to provide high-precision measurements of absolute structural vibration on bearing housings, casings, or structural supports. By utilizing a passive design, this transducer operates without external power, converting physical motion directly into an AC voltage output proportional to vibration velocity.
| Parameter | Specification Value |
|---|---|
| Manufacturer | Bently Nevada |
| Model Number | 9200-03-05-10-00 |
| Transducer Type | Two-wire moving-coil velocity transducer |
| Mounting Angle Option | 90 degrees plus/minus 2.5 degrees (Vertical) |
| Minimum Operating Frequency | 4.5 Hz (270 cpm) |
| Connection Option | Terminal block, top mount (no cable included) |
| Mounting Base | Circular base with M10x1 threaded stud |
| Agency Approvals | Option 00 (No hazardous area approvals) |
| Shipping Weight (Calculated) | 2.0 kg |
The top-mounted terminal block option simplifies on-site wiring without requiring proprietary molded connector cables. Ensure proper polarity connections to preserve signal phase relative to machinery vibration direction.
| Terminal designation | Signal Assignment |
|---|---|
| A (+) | Signal Positive (High side of coil) |
| B (-) | Signal Negative (Low side of coil / Common) |
| Shield / Case Ground | Cable shield termination (to be isolated at the sensor case and grounded at the monitor end only) |
The 9200 series moving-coil Seismoprobe is a legacy mechanical design. It is highly valued because it does not require external power loops, unlike modern solid-state piezo-velocity sensors (such as the Bently Nevada 330500 Velomitor). If you are replacing a 9200 unit, you must match the mounting angle option exactly. A vertical "-03" model (90 degrees) cannot be replaced with a horizontal "-01" or "-02" model, as the internal spring suspension is physically tuned to counteract gravity only at the specified operating orientation.
Cross-axis sensitivity is a known limitation of moving-coil transducers. To prevent physical wear on the internal coil guide and to avoid false signal generation, the sensor must not deviate more than plus/minus 2.5 degrees from the vertical axis. Additionally, check for nearby magnetic fields; because the 9200 uses an internal permanent magnet and moving coil, high-power magnetic fields from adjacent large motors can induce noise directly into the signal path.
When wiring to the terminal block, prevent dynamic stress on the terminals by installing a physical strain relief clamp within 100 mm of the sensor head. This prevents wiring fatigue from continuous structural vibration. Always use twisted, shielded cable (typically 18 AWG to 22 AWG) and ensure the shield is floated at the sensor and grounded at the rack monitor to mitigate ground loop noise.
Prepare the mounting surface. It must be flat, smooth, and free of paint, rust, or debris. A surface finish of 1.6 micrometers (63 microinches) or better is recommended.
Apply an approved thread-locking compound to the M10x1 stud threads. Thread the sensor onto the mounting hole and torque to the manufacturer's specification using a flat wrench on the housing hex flats (do not hand-tighten by twisting the terminal head).
Confirm vertical alignment using a precision level or inclinometer. The deviation from vertical must be less than 2.5 degrees.
Connect the field wiring to the terminal block. Secure the cable with local flexible conduit or strain-relief clamps to prevent mechanical fatigue on the connections.
Global Express Shipping
Returns & Warranty
Global Express Shipping
Returns & Warranty
Orders are processed and delivered Monday-Friday (excluding public holidays).
For full eligibility, restocking fees, and international return details, please view our official Refund & Return Policy .
| Country of origin |
United States
|
A field checklist for replacing a Beckhoff EL4032, covering the ±10 V load, terminal map, power contacts, EtherCAT state, and watchdog behavior.
Before replacing a Yokogawa AAI835, verify the 4-in/4-out channel map, power-loss loop behavior, barrier type, output load, cable, and redundancy.
ABB PM891K01 article 3BSE053241R1 is the non-redundant AC 800M processor kit. Use this field checklist before replacement.
Replacement checks for ABB TP853 3BSE018126R1: identify the installed CI853, CI855, CI857, or CI861 interface, record wiring, and verify communication after installation.
Engineering checks for the Allen-Bradley 5069-L330ERMS2: controller capacity, separate RTB kits, local I/O limits, network-node limits, and motion-axis count.
Checks to record before replacing ABB 3HNE 00006-1 DSQC 351: controller generation, X3/X5/X20/X21 wiring, DeviceNet settings, INTERBUS mapping, and LED states.
